HP CommonIO Products Bedienungsanleitung Seite 145
- Seite / 261
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
PAD Services
Remote PAD Printer Support (x29printd)
Chapter 6 145
Step 3. Configure the printer in the spooler system with the following
commands:
lpshut
lpadmin -v/dev/x29/x29printer1 -pfoo -mruggedwriter
lpsched
accept foo
enable foo
lpshut(1M) is necessary since lpadmin will not execute when lpsched is
running. You must restart LP scheduler after lpadmin. lpsched(1M)
schedules requests taken by lp(1) for line printing. After a printer is
configured in the spooler, you must enable it to accept printing requests.
Verifying the Configuration
After you complete the steps above, check the configuration as shown
below:
• lpstat -t should display the following (assuming that only this
printer is configured in the spooler system and you did these steps on
January 23, 11:00 am):
scheduler is running
no system default destination
device for foo: /dev/x29/x29printer1
foo accepting requests since Jan 23 11:00
printer foo is idle. enabled since Jan 23 11:00
fence priority : 0
• ps -ef should show that both lpsched and x29printd are running.
• /var/x25/log/x29printd/x29printd.log should have been
created and should contain information on the configuration of
/dev/x29/x29printer1.
• /var/x25/log/x29printd/x29printd.log should not contain any
configuration error messages.
- HP X.25/9000 User’s Guide 1
- Legal Notices 2
- Contents 3
- 1 About the X.25 Product 15
- About the X.25 Product 17
- Chapter 1 17 17
- Session (L5) Levels 18
- Transport Level (L4) 19
- Packet/network Level (L3) 20
- Chapter 122 22
- 2 Installation 23
- Hardware Requirements 24
- Software Requirements 27
- 3 Configuration 29
- Configuring the X.25 Link 30
- Configuring an X.25 Address 32
- Verifying Level 3 Values 39
- Verifying Level 2 Values 44
- Configuring X.25 over LLC2 54
- Configuration 58
- Chapter 358 58
- XOL_logical_port_id 1 66
- XOL_DSAP 0x70 66
- XOL_SSAP 0x70 66
- Configuring PAD Services 71
- Add/Modify UUCP Server 73
- Add/Modify X.3 Parameters 74
- Packages 77
- X.25 Cluster Definition 77
- X.25 over LLC2 81
- Local Failover 82
- Step 1. T 85
- Remote Failover 86
- longer required 89
- Service Guard 91
- Step 2. Con 93
- Chapter 394 94
- Chapter 3 95 95
- Verifying the X.25 Link 96
- 4 OLA/R Overview and Concepts 97
- Important Terms and Concepts 99
- Planning and Preparation 100
- Critical Resources 101
- Card using SMH 103
- OLA/R Overview and Concepts 110
- Chapter 4110 110
- 5 Diagnostic Utilities 111
- Using Diagnostic Utilities 112
- Break key as your interrupt 114
- Parameters) 115
- Diagnostic Utilities 116
- Chapter 5116 116
- Counters 123
- Chapter 5 125 125
- PER-VC STATISTICS FOR X25 126
- 126
- 6 PAD Services 129
- Introduction 130
- Packet Switching 131
- Overview 132
- User Level 133
- BSD Sockets 133
- 0x01000000 134
- System Requirements 140
- Examples 144
- UUCP Support (x29uucpd) 146
- Configuring UUCP PAD Support 147
- Local PAD Emulation (padem) 156
- Data Transfer Mode 157
- PAD Commands 160
- Extended Command Set 161
- Configuration Set Syntax 163
- Modifying Parameters 164
- X.3 Parameter Descriptions 165
- Ctrl-P, 32 to 126 permits 166
- Chapter 7 175 175
- Tracing and Logging Utilities 177
- Chapter 7 177 177
- Creating a Filter File 183
- Device File 188
- Sub code = 188
- Examples of strace Output 193
- Chapter 7196 196
- 8 Troubleshooting 197
- Run x25stat 200
- Statistics dispayed 200
- Troubleshooting 202
- Chapter 8202 202
- Reporting Problems 209
- Eliminator 211
- Commands 212
- Examples of x25init 214
- File Mapping Parameters 216
- Appendix A 219 219
- Appendix A224 224
- X.25 Configuration Files 226
- Example Files 228
- Appendix B 229 229
- Table B-6 (Continued) 229
- Appendix B230 230
- The x25init_smpl File 231
- Appendix B232 232
- Table B-7 (Continued) 232
- The x3config File 233
- Appendix B234 234
- Appendix B 235 235
- The x29hosts File 236
- C Diagnostic Messages 239
- Diagnostic Message Example 241
- Cause Code Settings 242
- Packet Codes 243
- X.25 Diagnostic Messages 244
Verwandte Produkte und Handbücher für Vernetzung HP CommonIO Products
Vernetzung HP 10-Base-T Installationshandbuch
(54 Seiten)
(54 Seiten)
Vernetzung HP Ps1810-8g Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung HP 2C Installationsanleitung
(36 Seiten)
(36 Seiten)
Vernetzung HP Moonshot-45XGc Betriebsanweisung
(124 Seiten)
(124 Seiten)
Vernetzung HP LCS60 Bedienungsanleitung
(432 Seiten)
(432 Seiten)
Vernetzung HP 6212 Bedienungsanleitung
(101 Seiten)
(101 Seiten)
Vernetzung HP 3162 Bedienungsanleitung
(199 Seiten)
(199 Seiten)
Vernetzung HP 3Com Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Vernetzung HP G510g Einstellungsanleitung
(4 Seiten)
(4 Seiten)
Vernetzung HP S10 Bedienungsanleitung
(134 Seiten)
(134 Seiten)
Vernetzung HP MSM3XX Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Vernetzung HP 10BASE-T Installationshandbuch
(16 Seiten)
(16 Seiten)
Western Reserve Controls 1782-JDC manuály
Uživatelské manuály a uživatelské příručky pro Brány / ovladače Western Reserve Controls 1782-JDC.
Poskytujeme 3 manuály pdf Western Reserve Controls 1782-JDC ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern