HP CommonIO Products Bedienungsanleitung Seite 108
- Seite / 261
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
OLA/R Overview and Concepts
How to On-line Add (OLA) a J3525A PCI Card using SMH
Chapter 4108
Output messages from the CRA process are presented in the Analyze
Critical Resources screen which will be shown before you can
proceed. The messages displayed on this screen and the availability to
continue on from it (“OK” button activated) depend on the results of the
analysis.
SMH displays a dialog indicating that the selected slot has power
disabled and it is now safe to add the card to the desired slot.
Step 9. At this point, the amber LED is activated and the green LED is off. Now
add the new PCI card. Refer to the system manual for the insertion of the
PCI card.
Table 4-3 Three Possible Critical Resource Analysis (CRA) Outcomes
Outcome Notes
Screen
Displays
Buttons
Activate
d
User Actions
No
critical
resources
identified.
At this point, you
can still cancel
the replacement
process.
“No affected
resources are
critical or
in-use” and
“Critical
Resource
Analysis
complete”
messages.
OK and
Cancel
Click “Cancel” to
halt the operation no
change to the
system. Or,
Click “OK” to take
you to the next step .
Critical
resource(s
)
identified.
SMH will not
allow the
operation to
proceed.
Detailed
message
describing the
affected
critical
resource.
Cancel Click “Cancel” to
halt the operation
with no change to
the system
Other
resources
identified.
SMH reports
other resources
that are in use
with no detectable
alternates. For
these resources,
you can cancel or
continue the
operation based
on your
knowledge of the
current system
configuration.
Detailed
message
describing
these
resources.
OK and
Cancel
Click “Cancel” to
halt the operation
with no change to
the system.
Click “OK” to
continue operations
based on your
knowledge of the
information being
reported.
- HP X.25/9000 User’s Guide 1
- Legal Notices 2
- Contents 3
- 1 About the X.25 Product 15
- About the X.25 Product 17
- Chapter 1 17 17
- Session (L5) Levels 18
- Transport Level (L4) 19
- Packet/network Level (L3) 20
- Chapter 122 22
- 2 Installation 23
- Hardware Requirements 24
- Software Requirements 27
- 3 Configuration 29
- Configuring the X.25 Link 30
- Configuring an X.25 Address 32
- Verifying Level 3 Values 39
- Verifying Level 2 Values 44
- Configuring X.25 over LLC2 54
- Configuration 58
- Chapter 358 58
- XOL_logical_port_id 1 66
- XOL_DSAP 0x70 66
- XOL_SSAP 0x70 66
- Configuring PAD Services 71
- Add/Modify UUCP Server 73
- Add/Modify X.3 Parameters 74
- Packages 77
- X.25 Cluster Definition 77
- X.25 over LLC2 81
- Local Failover 82
- Step 1. T 85
- Remote Failover 86
- longer required 89
- Service Guard 91
- Step 2. Con 93
- Chapter 394 94
- Chapter 3 95 95
- Verifying the X.25 Link 96
- 4 OLA/R Overview and Concepts 97
- Important Terms and Concepts 99
- Planning and Preparation 100
- Critical Resources 101
- Card using SMH 103
- OLA/R Overview and Concepts 110
- Chapter 4110 110
- 5 Diagnostic Utilities 111
- Using Diagnostic Utilities 112
- Break key as your interrupt 114
- Parameters) 115
- Diagnostic Utilities 116
- Chapter 5116 116
- Counters 123
- Chapter 5 125 125
- PER-VC STATISTICS FOR X25 126
- 126
- 6 PAD Services 129
- Introduction 130
- Packet Switching 131
- Overview 132
- User Level 133
- BSD Sockets 133
- 0x01000000 134
- System Requirements 140
- Examples 144
- UUCP Support (x29uucpd) 146
- Configuring UUCP PAD Support 147
- Local PAD Emulation (padem) 156
- Data Transfer Mode 157
- PAD Commands 160
- Extended Command Set 161
- Configuration Set Syntax 163
- Modifying Parameters 164
- X.3 Parameter Descriptions 165
- Ctrl-P, 32 to 126 permits 166
- Chapter 7 175 175
- Tracing and Logging Utilities 177
- Chapter 7 177 177
- Creating a Filter File 183
- Device File 188
- Sub code = 188
- Examples of strace Output 193
- Chapter 7196 196
- 8 Troubleshooting 197
- Run x25stat 200
- Statistics dispayed 200
- Troubleshooting 202
- Chapter 8202 202
- Reporting Problems 209
- Eliminator 211
- Commands 212
- Examples of x25init 214
- File Mapping Parameters 216
- Appendix A 219 219
- Appendix A224 224
- X.25 Configuration Files 226
- Example Files 228
- Appendix B 229 229
- Table B-6 (Continued) 229
- Appendix B230 230
- The x25init_smpl File 231
- Appendix B232 232
- Table B-7 (Continued) 232
- The x3config File 233
- Appendix B234 234
- Appendix B 235 235
- The x29hosts File 236
- C Diagnostic Messages 239
- Diagnostic Message Example 241
- Cause Code Settings 242
- Packet Codes 243
- X.25 Diagnostic Messages 244
Verwandte Produkte und Handbücher für Vernetzung HP CommonIO Products
Vernetzung HP 10-Base-T Installationshandbuch
(54 Seiten)
(54 Seiten)
Vernetzung HP Ps1810-8g Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung HP 2C Installationsanleitung
(36 Seiten)
(36 Seiten)
Vernetzung HP Moonshot-45XGc Betriebsanweisung
(124 Seiten)
(124 Seiten)
Vernetzung HP LCS60 Bedienungsanleitung
(432 Seiten)
(432 Seiten)
Vernetzung HP 6212 Bedienungsanleitung
(101 Seiten)
(101 Seiten)
Vernetzung HP 3162 Bedienungsanleitung
(199 Seiten)
(199 Seiten)
Vernetzung HP 3Com Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Vernetzung HP G510g Einstellungsanleitung
(4 Seiten)
(4 Seiten)
Vernetzung HP S10 Bedienungsanleitung
(134 Seiten)
(134 Seiten)
Vernetzung HP MSM3XX Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Vernetzung HP 10BASE-T Installationshandbuch
(16 Seiten)
(16 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern