HP 10TB Betriebsanweisung Seite 75
- Seite / 181
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
12. If necessary, manually power on the servers.
Resolving an EMU upgrade issue
When upgrading the EMU firmware, if the EMU and the server blade initiating the upgrade are
not on the same subnet, the upgrade fails. The following message (an example) displays on the
Firmware tab of the System Monitoring and Maintenance tool:
Flash failed for Enclosure Management Unit (EMU) using cpXXXXXX.exe.
Check log files (C:\ProgramData\Hewlett-Packard\CMP\logs\firmware.log
and C:\CPQSYSTEM\log\cpqsetup.log) for further information.
The C:\CPQSYSTEM\log\EmuFlash.log displays the following information (an example only):
Enclosure Manager information:Product Name : HP CSP EMUPart Number :
620022-001Serial Number : PBCYU0G9V0C01XUUID :
99PBCYU0G9V0C01XManufacturer
: HPFirmware Ver. : EM: 1.10 Jul 12 2011; HM: 1.3EMU Type : 1Hw Version
: Rev. BAux Info : SVN: 3221 branches/QUIRE-CSP-1-10
1.10 Jul 12 2011
Starting Flash Routine
Launching Http Server
Host IP Address:
Host IP not found
If this issue occurs, configure the EMU and server blade networking to be on the same subnet and
retry the firmware upgrade.
Performing a coordinated reboot
A coordinated reboot requires that both server blades in the StoreEasy 5000 be shut down as part
of the firmware update process. Therefore, HP recommends that you perform this during a
maintenance window. While the system services will become available during this process,
maintenance is not complete until all the steps below have been completed. Using iLO, follow these
steps to complete the procedure:
1. Run the FMT on the server in slot 2 (lower slot). Once it has finished, power down the server
in slot 2.
2. Run the FMT on the server in slot 1 (upper slot). Once it has finished, power down the server
in slot 1.
NOTE: Firmware updates for the P1210m controller and any storage hard drives may take
some time to complete.
3. Wait approximately 30 seconds.
4. Press the power button on the blade in slot 1.
IMPORTANT: If the system is powered by less than 200 volts (for example, 110), you must
wait for blade 1 to complete its boot process before turning on the second blade.
5. Power on the blade in slot 2.
6. Run the FMT again to verify that the firmware updates have completed on the server in slot 1.
7. Run the FMT again to verify that the firmware updates have completed on the server in slot 2.
Upgrading hardware components
To replace a hardware component with an upgrade, follow the component removal and replacement
instructions in “Removing and replacing hardware components” (page 77). For example, to replace
Performing a coordinated reboot 75
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 HP StoreEasy 5000 Storage 6
- Software components 7
- Verify the kit contents 8
- Cable disk enclosures 9
- Cable disk enclosures 11 11
- SAS chain) 15
- 7. D2700 Disk Enclosure 2 16
- 8. D2700 Disk Enclosure 3 16
- Network connections 18
- 255.255.255.010.0.0.10EMU 19
- Network connections 19 19
- Power on the storage system 20
- New Password: ******** 23
- Confirm : ******** 23
- CustomerEMU-dnsName> 23
- Accessing the storage system 24
- Networking options 26
- Using Server Core 26
- Using notification alerts 29
- Configuring Alerts and Email 29
- HP System Management Homepage 33
- Overall System Health Status 34
- Component Status summary 34
- Enclosure 34
- 5. PCIe module1. LOM module 35
- 6. PCIe module2. LOM module 35
- Component LEDs 37
- Table 3 Front LED status 38
- Figure 27 Hard drive LEDs 39
- Figure 33 Power supply LEDs 43
- EMU CLI SHOW commands 45
- Known issues 46
- Error codes 53
- HP Support websites 65
- Autonomy LiveVault 66
- Windows Recovery Environment 66
- Memory Diagnostic 67
- HP 1210m Volume Online Tool 68
- Upgrading hardware components 75
- Customer self repair 77
- Replaceable parts 78
- Replaceable parts 79 79
- Verifying component failure 82
- Verifying proper operation 82
- Wait times for hard disks 82
- Removing the midplane board 86
- Replacing the midplane board 88
- Removing a SAS cable 89
- Replacing a SAS cable 89
- Removing the SAS I/O module 89
- Replacing the SAS I/O module 90
- Removing the fan module 91
- Replacing the fan module 92
- Removing the power supply 93
- Replacing the power supply 94
- Removing the PCIe module 95
- Replacing the PCIe module 96
- Removing the EMU module 97
- Replacing the EMU module 98
- Removing the front bezel 101
- Replacing the front bezel 102
- Removing the drive drawer 107
- Replacing the drive drawer 110
- Removing the enclosure rails 119
- Replacing the enclosure rails 122
- Removing the server blade 124
- Replacing the server blade 125
- Replacing the cache module 131
- Removing the capacitor pack 132
- Removing the Mezzanine NIC 134
- Replacing the Mezzanine NIC 135
- 7 Storage system recovery 136
- Recovering both servers 138
- Recovering a single server 138
- 140 Storage system recovery 140
- 142 Storage system recovery 142
- 8 Support and other resources 143
- Rack stability 144
- 9 Documentation feedback 145
- A Managing the EMU 146
- Authentication 147
- 148 Managing the EMU 148
- Authentication 149 149
- Time functions 150
- 152 Managing the EMU 152
- Inventory and status 153
- 154 Managing the EMU 154
- Inventory and status 155 155
- 156 Managing the EMU 156
- Inventory and status 157 157
- 158 Managing the EMU 158
- Internet control 159
- 160 Managing the EMU 160
- Server management 161
- 162 Managing the EMU 162
- Server management 163 163
- 164 Managing the EMU 164
- Enclosure control 165
- 166 Managing the EMU 166
- Enclosure control 167 167
- Forensic 168
- Forensic 169 169
- 170 Managing the EMU 170
- Session 171 171
- 172 Managing the EMU 172
- Activate Button Menu 173
- Reboot EM (bE) 174
- Restore Factory Defaults (Fd) 174
- Recover Lost Password (Fp) 174
- Set DHCP IP Address (dH) 174
- Exit Button Menu 175
- B Regulatory information 176
- HP Enterprise Servers 177
- HP Storage Products 177
- HP Networking Products 177
- Glossary 178
- 180 Index 180
Verwandte Produkte und Handbücher für Software HP 10TB
Software HP DL380-SL Betriebsanweisung
(141 Seiten)
(141 Seiten)
Software HP Switch 6120 Bedienungsanleitung
(469 Seiten)
(469 Seiten)
Software HP BMD00022 Bedienungsanleitung
(228 Seiten)
(228 Seiten)
Software HP SN6000 Betriebsanweisung
(122 Seiten)
(122 Seiten)
Software HP 3PAR Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Software HP NEOVIEW 544530-001 Bedienungsanleitung
(142 Seiten)
(142 Seiten)
Software HP 700wl Bedienungsanleitung
(388 Seiten)
(388 Seiten)
Software HP X9300 Installationsanleitung
(151 Seiten)
(151 Seiten)
Software HP SP1 Bedienungsanleitung
(143 Seiten)
(143 Seiten)
Software HP Q.11. (2510-24) Bedienungsanleitung
(294 Seiten)
(294 Seiten)
Software HP 441877-00F Bedienungsanleitung
(67 Seiten)
(67 Seiten)
Software HP 2000s Betriebsanweisung
(200 Seiten)
(200 Seiten)
Software HP 2012i Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Software HP XP12000 Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Software HP Moonshot-180G Betriebsanweisung
(719 Seiten)
(719 Seiten)
Software HP 377707-002 Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Software HP 1TB Bedienungsanleitung
(80 Seiten)
(80 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern