HP 10TB Betriebsanweisung PDF herunterladen (Seite 47)

Table 13 Known issues (continued)

ResolutionIssue

The use of this registry key is documented at http://support.microsoft.com/

kb/824344.

iSCSI Software Target service

on MACHINE_NAME. Error 1053:

The service did not respond

to the start or control

request in a timely manner.

The UID LED cannot be enabled or disabled in the System Management

Home page until the Enclosure Manager key has been generated. The

Enclosure Manager key can be generated using the System Manager snap-in.

The Enclosure UID page that is part of

the HP System Management Homepage

cannot be used to enable or disable the

UID status LED.

The reboot time for the network storage system is approximately six to seven

minutes.

Length of network storage system reboot

time

This issue can be resolved by doing one of the following:A cluster network interface reports status

(from cluster net or cluster

• Allow 12–24 hours to pass for the Microsoft Failover Cluster Manager to

resolve the issue automatically.

netint command or Failover Cluster

Manager) as “network partitioned” when

• Manually restart the node that was restarted or affected.

a cluster node is rebooted and rejoins

the cluster. The network interface is still

• Manually disable or enable the NIC on the affected cluster node that is

causing the issue, under Network Connections.

usable for communications to other

nodes; it is only the communications

between the cluster nodes that is

affected. The cluster interface status will

change after 12–24 hours. This issue is

intermittent and takes approximately

30–50 reboots of a node to reproduce.

FSRM only configures its config store in the cluster database when the FSRM

service starts. To resolve this issue, reboot one node in the cluster, or you

One of the following occurs:

• File Server Resource Manager (FSRM)

displays the error message:

File Server Resource

Manager global

can start/stop the FSRM services by issuing the following commands on the

command line using elevated privileges:

net stop srmsvc

net stop srmreports

configuration cannot be

accessed since it is not

installed yet.

net start srmreports

net start srmsvc

• A corrupted FSRM file causes the

following error message to display

This issue is documented by Microsoft at:

on the Quota window of the

Windows New Share wizard:

No quota templates are

available on this server.

http://technet.microsoft.com/en-us/library/gg214171(WS.10).aspx

The HP StoreEasy 5000 Storage does not have a VDS Hardware Provider,

so the Diskraid utility does not work.

The Diskraid utility does not operate with

the HP StoreEasy 5000 Storage.

HP strongly recommends using Active Directory or other RFC2307 compliant

LDAP stores for NFS user name mapping. Using Active Directory Lightweight

The NFS user mapping should not use

ADLDS.

Data Services (ADLDS) is not recommended. Configuring ADLDS in a clustered

environment is beyond the scope of this document.

The Onboard Administrator GUI Launch button only applies to systems with

the c3000/c7000 chassis. You are not able to use this button with the HP

StoreEasy 5000 Storage .

The Onboard Administrator GUI cannot

be launched from the Integrated

Lights-Out 3 page. The Launch button is

in the Active Onboard Administration

section under the BL c-Class node in the

Integrated Lights-Out 3 navigation tree.

Update the SAS I/O module firmware again. If the second update is

unsuccessful, review the log file for more information.

On rare occasions, an update to the SAS

I/O module firmware may result in the

following message: Flash failed

for xxxx half of SAS I/O

Module. Check log file yyyy

Known issues 47

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 180 181

Kommentare zu diesen Handbüchern

Keine Kommentare

HP 10TB Betriebsanweisung Seite 47

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software HP 10TB