HP 10TB Betriebsanweisung PDF herunterladen (Seite 51)

Table 13 Known issues (continued)

ResolutionIssue

Do not create network teams until after the initial configuration tasks have

been completed. If a system is to be connected to a network where specific

Network teaming cannot be configured

during initial system configuration.

VLANs with VLAN tagging enabled (for example, for connecting to a domain

controller), it is recommended that the network switch be temporarily

configured to pass untagged network packets on the specific VLAN or to

configure the network interface properties to operate using the specific VLAN

ID. Configuring VLAN settings is accomplished by opening the properties

dialog for the network interface and then configuring the network adapter

by clicking on the Configure button.

This may be cause by having multiple interfaces on the same network subnet

as that used by the network interface names “Cluster Internal”. By default,

During initial system configuration, the

Initial Configuration Tasks window may

display the following message:

Connecting to remote server

169.254.2.111 failed with the

the Cluster Internal network uses an APIPA address (169.254.0.0/16). This

is the default subnet used by other network interfaces that are connected and

there is no DHCP server. This results in multiple network routes between

nodes.

Disable or disconnect network interfaces that are connected to networks

where no DHCP server is available. During the initial configuration you will

following error message: The

WinRM client cannot process

the request. If the

be given the opportunity to assign network addresses to other network

authentication scheme is

interfaces. After addresses are assigned the network interfaces can be

reconnected or enabled.

different from Kerberos, or

if the client computer is not

joined to a domain, then

HTTPS transport must be used

or the destination machine

must be added to the

TrustedHosts configuration

setting. Use winrm.cmd to

configure TrustedHosts. Note

that computers in the

TrustedHosts list might not

be authenticated.

You must upgrade the HP 1210m controller first and reboot the server. Then,

upgrade the disk enclosure firmware and it will succeed.

If the HP 1210m controller in the HP

StoreEasy 5000 Storage is running an

older version (1.56 or earlier) when you

perform a firmware upgrade, the

upgrade to the disk enclosure I/O

module will fail. The Firmware Update

Tool (FMT) will display the following

message: "Version not updated after

flash and reset of SEPxxxxxxxxxxxxxxx".

Set the system level proxy to explicitly bypass the HA file servers. For example,

instead of using the following command:

netsh winhttp set proxy myproxy.fabrikam.com:80

"<local>"

When attempting to use Failover Cluster

Manager to add a File Share to an HA

File Server on the cluster, the Add Share

wizard will not start.

Also, attempting to use Failover Cluster

Manager to view any existing shares on

set the proxy using a command like the following:

netsh winhttp set proxy myproxy.fabrikam.com:80

"<local>;*.fabrikam.com"

file servers in the cluster, just results in a

perpetual “Loading” message. This

happens when a system level HTTP proxy

In this example, “*.fabrikam.com” is the client access point used on the

HA file servers.

server is set. Some users will require a

system level proxy to make Cluster

Aware Updating work, but if one is set,

it is important to explicitly prevent access

to your HA file servers from using the

proxy.

The Storage Management Provider

displays the following error message:

0x26005054 The service failed

to subscribe for events

1. Open Add/Remove Programs and verify that HP Insight Management

Agents is installed.

2. If it is installed, open the Run dialog box and enter WBEMTEST and click

Connect.

3. Enter root\hpq as the namespace. Wait to see if the namespace

connects. If it does not connect, the WBEM installation is corrupt.

Known issues 51

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 180 181

Kommentare zu diesen Handbüchern

Keine Kommentare

HP 10TB Betriebsanweisung Seite 51

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software HP 10TB