HP B8C95AA Bedienungsanleitung Seite 79
- Seite / 490
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
HP Designjet T Series — Service Manual 2-19
System Error Codes - Full Descriptions
System Error: 48:YZ
Problem
Description:
PPS system failure.
Corrective Action: Try the following:
1 Switch the Power OFF from the back of the Printer and disconnect the Power
cor
d. Reconnect the power cord and power On the Printer.
2 Check that the Pen to Paper Space (PPS) Solenoid cable is not damaged and
is
correctly connected to the PrintMech PCA.
3 Perform the Scan Axis PRS diagnostic test to troubleshoot the problem further.
See
PRS Test on page 3-9.
4 Make sure the Service Station is correctly installed. Sometimes, if the Service
S
tation is not correctly installed, the front of the Service Station falls down
(causing the Service Station to be tilted), and the L-Bracket support does not
fit properly. The front of the Service Station should be “UP,” and the L-Bracket
should fit well with the Service Station.
5 R
eplace the Pen to Paper Space (PPS) Solenoid. See
Pen to Paper Space
(PPS) Solenoid (T1100/T1100ps/T610) on page 6-75 or Pen to Paper
Space (PPS) Solenoid (T1120/T1120ps) on page 6-77.
6 If the System Error continues, replace the PrintMech PCA. See
PrintMech
PCA (T1100, T1100ps, T610 ONLY) on page 6-73.
System Error:
51:YZ
Problem
Description:
Window Sensor failure.
Corrective Action: Try the following:
1 Check that the Window Position Sensor cable is not damaged and is
cor
rectly connected to the PrintMech PCA.
2 Perform the Sensors Test to troubleshoot the problem further. See
5. Sensors
on page 3-31.
3 Replace the Window Position Sensor. See
Window Position Sensor on page
6-53.
System Error:
52:10
Problem
Description:
The printer has detected fibers in the Drop Detector.
Corrective Action: Try the following:
1 Switch the Power OFF from the back of the Printer and disconnect the Power
cor
d. Reconnect the power cord and power On the Printer.
2 Check that the Drop Detector cable is not damaged
and is correctly
connected to the PrintMech PCA.
3 Clean the drop detector.
4 Check that the Service Station cable is not damaged and is correctly
connec
ted to the PrintMech PCA.
- Table of Contents 1 3
- Using this Manual 4
- Troubleshooting 1 5
- General Troubleshooting 8
- 5. Sensors on page 3-31 9
- Print quality troubleshooting 13
- (Main Menu/ 21
- Ink Supplies Troubleshooting 43
- HP 72 69 ml Photo Black Ink 44
- Cartridge 44
- Solving Ink Supplies Problems 57
- 1System Error Codes 1 61
- PCA and Formatter 63
- Reading a System Error Code 64
- System Error Code Table 64
- Corrective Actions Table 66
- 08:YZ (T1120/T1120ps ONLY) 70
- *Flashing* 71
- 71:04 (T610 printers ONLY) 82
- 75.21:YZ 87
- 75.22:YZ 88
- Possible causes 94
- The printer’s queue 95
- System Error Codes 108
- Service Tests and Utilities 2 109
- Introduction 110
- Service Tests (Diagnostics) 111
- Using the Front Panel 113
- 1. Scan Axis 114
- System Error Code 42:XZ 115
- System Error Code 47:XZ 115
- System Error Code 73:XZ 115
- 2. Paper Drive 126
- 3. Electronics Module 129
- Starting DelSol1 131
- Getting PCA revision 131
- Getting Memory Size 131
- Getting HDA info 132
- Getting File System Info 132
- Getting MainBoard Rev 132
- Getting Main Memory Size 132
- Starting Micci2Bus 133
- Starting Micci2BusProxy 133
- Checking Communications 133
- 4. Carriage Assembly 134
- 5. Sensors 139
- 6. Rewinder 142
- 7. Ink Delivery System (IDS) 144
- Starting AcumenSupplies 146
- Reading AcumenSupplies 146
- 8. Service Station 150
- Capping Service Station 152
- Starting Nvm 154
- Starting TestsGpio 154
- Getting Part number 154
- Reading Aerosol Fan 154
- Turning on Aerosol Fan 155
- Checking Fault condition 155
- 9. I/O Information 156
- 10. Unit Information 157
- 11. EEROM Reset 158
- 12. Set Unit Configuration 159
- 13. Error 71:19 Recovery 159
- 14. Others 163
- Service Utilities 164
- 1. Turn Drive Roller 166
- 2. Purge Tubes 168
- 3. Set SN 170
- 4. Reset Life Counters 171
- 5. Diagnostic Print 173
- 6. Set Date and Time 173
- 7. Enable/Disable Firewall 174
- 8. Reset User Life Counters 175
- 9. Enable/Disable Sleep Mode 176
- 10. Disk Wipe DoD 5220.22OM 177
- 11. SNMP 179
- 12. New Left Spittoon 180
- 14. Enable/Disable Port 280 181
- Service Tests 183
- 1. Test Messages 184
- 2. I/O Tests 184
- Service Tests and Utilities 186
- Service Calibrations 3 187
- Service Calibrations 188
- Scan Axis Calibration 190
- Service Station Calibration 191
- Paper Advance Calibration 192
- Advancing Paper 195
- Printing Pattern 195
- Drop Detector Calibration 198
- Line Sensor Calibration 201
- Carriage PCA 204
- Parts and Diagrams 4 205
- Printer Support 206
- Figure 5-1: Printer Support 207
- Center Covers (Front) 208
- Center Covers (Rear) 210
- Right Cover 212
- Figure 5-4: Right Cover 213
- Left Cover 214
- Figure 5-5: Left Cover 215
- Right Hand Assemblies 216
- Left Hand Assemblies 218
- Paper Path Assemblies (Rear) 230
- Tool Kits 232
- Figure 5-14: Tool Kits 233
- Miscellaneous Parts 234
- New Formatter Design 235
- Parts and Diagrams 236
- Removal and Installation 5 237
- Required Tools 240
- Bin Assembly 246
- Front Cover 252
- Media Output Assembly 253
- Removal and Installation 254
- Right Front Trim 255
- Left Front Trim 257
- Right Ink Cartridge Door 259
- Left Ink Cartridge Door 261
- 8. Unclip the Right Trim 265
- Rear Tray 271
- Rear Cover 272
- Media Lever 273
- Media Lever Position Sensor 276
- Cutter Assembly 278
- Right Rear Tray Support 279
- Left Rear Tray Support 281
- Front Panel 283
- Top Cover 286
- Window Position Sensor 289
- Drop Detector 305
- T1120/T1120ps printers 307
- Left Spindle Holder 316
- Installation 321
- Clean Out Assembly 326
- Out Of Paper Sensor 327
- Left Roll Guide 330
- Right Roll Guide 331
- T1100ps/T610) 332
- Encoder Strip 337
- Carriage Rear Bushing 373
- 6. Remove the left bumper 376
- Belt Assembly 377
- Carriage Rail Oiler 386
- Line Sensor (T1120/T1120ps) 393
- Carriage PCA (T1120/T1120ps) 414
- Left Ink Supply Station 419
- Formatter 436
- Starwheel Assembly 444
- Print Zone Overdrive 446
- Left Spittoon 450
- Media Advance Drive 454
- Pinchwheel Assembly 465
- Left Starwheel Lifter 473
- Starwheel Motor 481
- Full Bleed Foam 483
- Preventive Maintenance 5 485
- Preventive Maintenance 486
- General Cleaning 487
- Level of Printer Usage 487
- Preventive Maintenance Kits 489
- Preventive Maintenance Kit #2 490
- Preventive Maintenance Kit #3 490
Verwandte Produkte und Handbücher für Drucken & Scannen HP B8C95AA
Drucken & Scannen HP FB500 Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Drucken & Scannen HP CP3525 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Drucken & Scannen HP Z5200 Bedienungsanleitung
(197 Seiten)
(197 Seiten)
Drucken & Scannen HP A440 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Drucken & Scannen HP PSC-500 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Drucken & Scannen HP cp1700 Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Drucken & Scannen HP Printer 800 Bedienungsanleitung
(246 Seiten)
(246 Seiten)
Drucken & Scannen HP 1050C Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Drucken & Scannen HP C6240 Bedienungsanleitung
(35 Seiten)
(35 Seiten)
Drucken & Scannen HP F2410 Betriebsanweisung
(16 Seiten)
(16 Seiten)
Drucken & Scannen HP 1150Cse Bedienungsanleitung
(74 Seiten)
(74 Seiten)
Drucken & Scannen HP C6340 Einstellungsanleitung
(16 Seiten)
(16 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern