Hp ProLiant DL380 Server Bedienungsanleitung Seite 11
- Seite / 128
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Component identification 11
Systems Insight Display LED combinations
When the health LED on the front panel illuminates either amber or red, the server is experiencing a health
event. Combinations of illuminated Systems Insight Display LEDs, the system power LED, and the health LED
indicate system status.
Systems Insight Display
LED and color
Health LED
System power
LED
Status
Processor (amber)
Red Amber One or more of the following conditions may
exist:
•
Processor in socket X has failed.
•
Processor X is not installed in the socket.
•
Processor X is unsupported.
•
ROM detects a failed processor during
POST.
Processor (amber)
Amber Green Processor in socket X is in a pre-failure
condition.
DIMM (amber)
Red Green One or more DIMMs have failed.
DIMM (amber)
Amber Green DIMM in slot X is in a pre-failure condition.
Over temp (amber)
Amber Green The Health Driver has detected a cautionary
temperature level.
Over temp (amber)
Red Amber The server has detected a hardware critical
temperature level.
PCI riser (amber)
Red Green The PCI riser cage is not seated properly.
Fan (amber)
Amber Green One fan has failed or has been removed.
Fan (amber)
Red Green Two or more fans have failed or been
removed.
Power supply (amber)
Red Amber One or more of the following conditions may
exist:
•
Only one power supply is installed and
that power supply is in standby.
•
Power supply fault
•
System board fault
Power supply (amber)
Amber Green One or more of the following conditions may
exist:
•
Redundant power supply is installed and
only one power supply is functional.
•
AC power cord is not plugged into
redundant power supply.
•
Redundant power supply fault
•
Power supply mismatch at POST or
power supply mismatch through hot-plug
addition
Power cap (off)
— Amber Standby
Power cap (green)
— Flashing green Waiting for power
Power cap (green)
— Green Power is available.
IMPORTANT:
If more than one DIMM slot LED is illuminated, further troubleshooting is required.
Test each bank of DIMMs by removing all other DIMMs. Isolate the failed DIMM by replacing
each DIMM in a bank with a known working DIMM.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Item Description Status 9
- Press and release the panel 9
- Systems Insight Display LEDs 10
- Rear panel components 12
- Rear panel LEDs and buttons 12
- System board components 14
- System maintenance switch 15
- NMI functionality 16
- DIMM slot locations 16
- SAS and SATA device numbers 17
- PCI riser cage LED 17
- Hot-plug fans 19
- Component identification 20 20
- Operations 21
- Remove the access panel 22
- Install the access panel 23
- Remove the hot-plug fan cage 24
- Remove the hot-plug fan 25
- Install the PCI riser cage 27
- Remove the air baffle 29
- Rack planning resources 31
- Optimum environment 31
- Temperature requirements 32
- Power requirements 33
- Rack warnings 34
- Installing hardware options 35
- Registering the server 38
- Introduction 39
- Processor and fan option 39
- Install the heatsink 44
- Remove the two fan blanks 44
- Memory options 46
- HP SmartMemory 47
- DIMM identification 48
- Memory configurations 49
- Installing a DIMM 51
- Hot-plug hard drive options 52
- Controller options 54
- Optical drive option 58
- FlexLOM option 61
- Expansion board options 63
- Hard drive cage option 68
- Remove the fan cage 70
- 13. Connect the cables: 72
- Install the fan cage 75
- Install the air baffle 75
- 2U rack bezel option 77
- 7. Reboot the server 81
- Cabling 82
- Optical drive cabling 83
- FBWC cabling 84
- Chipset SATA cable option 85
- 150W PCIe power cable option 88
- Server mode 89
- Server QuickSpecs 89
- HP iLO Management Engine 89
- Active Health System 90
- Intelligent Provisioning 91
- Erase Utility 92
- HP Service Pack for ProLiant 93
- HP ROM-Based Setup Utility 94
- Boot options 95
- Configuring AMP modes 95
- Utilities and features 96
- ROMPaq utility 97
- Automatic Server Recovery 98
- USB support 98
- Redundant ROM support 98
- Keeping the system current 99
- ProLiant Servers 100
- Troubleshooting 101
- Battery replacement 102
- FCC rating label 103
- Modifications 104
- • EMC Directive 2004/108/EC 105
- BSMI notice 106
- Korean notice 106
- Japanese notice 106
- Chinese notice 107
- Laser compliance 107
- Battery replacement notice 107
- Electrostatic discharge 109
- Specifications 110
- Specification Value 113
- Technical support 114
- Technical support 115 115
- Customer Self Repair 116
- Technical support 117 117
- Reparo feito pelo cliente 118
- Technical support 119 119
- Technical support 120 120
- Technical support 121 121
- Acronyms and abbreviations 122
- Documentation feedback 125
- Index 126 126
- Index 127 127
- Index 128 128
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant DL380 Server
(88 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern