Hp ProLiant DL380 G5 Server Bedienungsanleitung Seite 45
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
IMPORTANT: Never turn off a storage system when the attached system is still turned on.
• Check the physical proximity of the system to other electrical devices. Since electrical noise may cause this
error, check the AC circuit for other electrical devices.
Timeouts can be caused when two or more drives are set to the same SCSI ID. Ensure that the storage
system and system SCSI IDs do not conflict.
• On a storage system, check the SCSI ID cable on the drive tray. If the cable is damaged or incorrectly
installed, SCSI Timeouts can occur. See the documentation accompanying the Hot Plug Drive Tray Service
Spare Kit.
• Ensure that the system temperature is within specified limits. Ensure that the fans are operating and are not
blocked.
In some instances, drive failure can cause Timeouts. If you continue to receive many of these errors, replace
the drive.
• SCSI Bus Faults—Displays the number of times that SCSI bus parity, overrun, or underrun errors have been
detected on the SCSI bus. Since the controller retries the operation, SCSI bus faults can cause a drop in
performance, or, in some cases, data corruption.
If the count is not zero and the drive has failed, the failure might be correctable without replacing the drive.
Verify the status of the drive by checking the following:
• Ensure that all system and storage system cables are intact and seated properly. You may need to replace
the cables.
• Check the physical proximity of the system to other electrical devices. Since electrical noise may cause a
Bus Fault error, check the AC circuit for other electrical devices.
• Ensure that the system temperature is within specified limits. Ensure that fans are operating and are not
blocked.
SCSI Bus Faults can be caused when two or more drives are set to the same SCSI ID. Ensure that storage
system and system SCSI IDs do not conflict.
In some instances, drive failure can cause SCSI Bus Faults. If you continue to receive many of these errors,
replace the drive.
• IRQ Deglitch—Displays the number of times that a glitch has been detected on the drive interface cable. Since
the controller retries the operation, problems can cause a drop in performance or, in some cases, data
corruption. Glitches indicate electrical noise on the drive cable or an intermittent failure of the drive electronics.
This item is considered a Problem Indicator that may be correctable without replacing the drive. Verify the status
of the drive by checking the following:
• Ensure that all system and storage system cables are intact and seated properly. You may need to replace
cables.
• Check the physical proximity of the system to other electrical devices. Since electrical noise may cause a
glitch error, check the AC circuit for other electrical devices.
• If you continue to receive many of these errors, replace the drive.
Failure Indicators
Use the Failure Indicators to determine the cause of a drive failure. Typically, the number of failures is zero when the
drive is operating normally. If a counter is not zero and the drive has not failed, there could be an intermittent
problem that may require the drive to be replaced.
The Failure Indicators are:
• Spinup Errors—When the physical drive fails due to the failure of a spin-up command, a Spinup Error occurs. If
the failure count is not zero and the drive has failed, replace the drive.
If the counter is not zero and the drive is OK (has not failed), there may be an intermittent problem that requires
drive replacement. If you observe that the count is increasing over time, replace the drive.
• Aborted Commands—The Aborted Commands counter records the number of times that a physical SCSI drive
returned an Aborted Command status when a SCSI command was attempted. This error count indicates
unsuccessful termination of the SCSI command. When the physical drive is failed due to aborted commands that
could not be retried successfully, Aborted Commands errors occur. If the number of errors is not zero and the
drive has failed, replace the drive.
If the counter is not zero and the drive is OK (has not failed), there may be an intermittent problem that requires
drive replacement. If you observe that the count is increasing over time, replace the drive.
Agent information 45
- HP Insight Management Agents 1
- Contents 3
- Contents 4 4
- Browser requirements 5
- Obtaining JVM from Microsoft 6
- Obtaining JVM from Sun 6
- Introduction 8
- Overview 8
- Logging in 9
- System Management Homepage 10
- Header frame 11
- Body frame 13
- Home tab 13
- Settings tab 15
- SNMP Webagent 16
- Security 17
- User Preferences 18
- UI Properties 18
- Tasks Tab 19
- Logs tab 19
- Webapps tab 19
- Support tab 20
- Help tab 20
- 2 Agent information 21
- System Agent 22
- Sub system Classification 23
- Cooling and temperature 24
- Agent information 25 25
- Agent information 26 26
- Memory Summary 27
- Memory Details 27
- Processors 28
- PCI Devices 28
- Management Processor 29
- Battery 30
- Modem/COM Port Settings 30
- Operating System 31
- Logical Disk Space 32
- Server 33
- Agent information 34 34
- Network 35
- Processes 35
- Processor Utilization 36
- Agent information 37 37
- Agent information 38 38
- Agent information 39 39
- Identify Drives 40
- Physical Drive Information 41
- Agent information 42 42
- Logical Drive Information 43
- Predictive Indicators 44
- Problem Indicators 44
- Failure Indicators 45
- Statistics 46
- Agent information 48 48
- Identify Drive 49
- Associated Tape Drives 50
- Tape Drive Information 50
- Agent information 51 51
- Storage Systems 52
- Agent information 53 53
- IDE controllers 54
- IDE controller information 54
- IDE ATAPI devices 54
- IDE ATA disk drives 54
- Logical drives 55
- IDE ATA logical drives 55
- Physical drives 56
- Spare drives 56
- SCSI controllers 56
- Controller information 56
- SCSI device information 57
- Tape library 58
- Tape devices 59
- CD storage system 60
- CD Library Information 60
- CD-ROM drive information 61
- SCSI physical drives 62
- Drive indicators 63
- Drive statistics 64
- SCSI logical drives 65
- SCSI bus information 66
- System Configuration 67
- System Board 68
- Advanced Memory Protection 69
- Agent information 70 70
- ROM Microcode Patches 71
- General I/O Devices 71
- System Resources 72
- System Summery 72
- Enclosure Information 73
- Agent information 74 74
- Agent information 75 75
- Critical Error Log 76
- Agent information 77 77
- Correctable errors 78
- Power-On Messages 78
- Integrated Management Log 78
- Operating system overview 79
- Summary page 79
- File System page 80
- User Information page 80
- Connection page 81
- Loaded NLMs page 81
- Server Parameter page 82
- Physical Partition page 82
- Adapter Information page 83
- Mass storage RAID Array 84
- Mass Storage Physical 84
- Mass Storage controller 85
- Mass Storage Summary 85
- Environment Monitoring Unit 85
- External Expansion Cabinet 86
- Telephone numbers 87
- Appendix A Troubleshooting 88
- SNMP community string issues 90
- issues 90
- Insight Manager issues 91
- Other problems 93
- Glossary 95
- Glossary 96 96
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant DL380 G5 Server
(74 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.503 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern