HP Digital AlphaStation 255 Family Technical Information Seite 120
- Seite / 353
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4.10 info
The info command displays registers and data structures. You can enter the command
by itself or followed by a number (0 − 8). If you do not specify a number, a list of
selections is displayed and you are prompted to enter a selection.
The following commands are available:
info 0
Displays the SRM memory descriptors as described in the Alpha System Reference
Manual.
info 1
Displays the page table entries (PTE) used by the console and operating system to map
virtual to physical memory. Valid data is displayed only after a boot operation.
info 2
Dumps the Galaxy Configuration Tree (GCT) FRU table. Galaxy is a software
architecture that allows multiple instances of OpenVMS to execute cooperatively on a
single computer.
info 3
Dumps the contents of the system control status registers (CSRs) for the
C-chip, D-chip, and P-chips.
info 4
Displays the per CPU impure area in abbreviated form. The console uses this scratch
area to save processor context.
info 5
Displays the per CPU impure area in full form.
info 6
Displays the per CPU machine check logout area.
info 7
Displays the contents of the Console Data Log.
info 8
Clears all event frames in the Console Data Log.
For information about the data displayed by the info commands, see the following
documents:
• For info 0, info 1, and info 4, see the Alpha System Reference Manual.
• For info 2, see the Galaxy Console and Alpha Systems V5.0 FRU Configuration Tree
Specification.
• For info 3, see the Titan 21274 Chipset Functional Specification.
• For info 6 and info 7, see the AlphaServer DS15 Platform Fault Management
Specification.
Example 4–8 info 0
>>>info
4-24 hp AlphaServer/AlphaStation DS15 Service Guide
- Service Guide 1
- Contents 5
- Preface 15
- Documentation Titles 16
- Information on the Internet 16
- Chapter 1 17
- System Overview 17
- System Overview 1-3 19
- 1.2 Common Components 21
- 1.3 Front View 22
- 1.4 Top View 24
- 1.5 Rear Ports and Slots 26
- 1.6 Network Connections 28
- 1.7 Operator Control Panel 30
- 1.8 System Motherboard 32
- 1.10 Storage Cage Options 36
- 1.11 Console Terminal 40
- System Overview 1-25 41
- 1.12 Power Connection 42
- 1.13 System Access Lock 44
- Chapter 2 45
- Troubleshooting 45
- 2.1 Questions to Consider 46
- 2.2 Diagnostic Categories 47
- 2.2.1 Error Beep Codes 48
- Table 2–2 OCP Switches 49
- 2.2.3 Power Problems 51
- Symptom Action 52
- Troubleshooting 2-9 53
- 2.2.6 Boot Problems 54
- 2.2.8 Memory Problems 56
- 2.2.9 PCI Bus Problems 57
- 2.2.10 SCSI Problems 58
- 2.3.3 Required Firmware 61
- 2.4 Updating Firmware 62
- Troubleshooting 2-19 63
- 2.5.2 Loopback Tests 64
- 2.5.3 SRM Console Commands 64
- 2.5.5 Crash Dumps 65
- 2.6.1 Installing Q-Vet 68
- 2.6.2 Running Q-Vet 70
- Analyzer” 72
- 2.6.4 De-Installing Q-Vet 73
- 2.7 Information Resources 74
- 2.7.4 Fail-Safe Booter 75
- 2.7.5 Software Patches 75
- 2.7.6 Learning Utility 75
- 2.7.8 Supported Options 75
- Chapter 3 77
- 1.65V enable 80
- 3.3 Power-Up Displays 81
- Power-Up Sequence 82
- 3.3.3 SRM Console Event Log 86
- 3.4 Power-Up Error Messages 88
- 3.4.1 Checksum Error 89
- 3.6 Updating the RMC 95
- Chapter 4 97
- SRM Console Diagnostics 97
- Command Function 99
- 4.2 Buildfru 100
- Options 103
- 4.3 cat el and more el 104
- 4.4 clear_error 105
- 4.5 crash 106
- 4.6 deposit and examine 107
- 4.7 exer 111
- last read or write 114
- 4.8 grep 116
- 4.9 hd 118
- 4.10 info 120
- >>> info 1 122
- Example 4–10 info 2 123
- Example 4–11 info 3 124
- Example 4–12 info 4 125
- Example 4–13 info 5 127
- Example 4–14 info 6 130
- Example 4–15 info 7 132
- Example 4–16 info 8 134
- 4.11 kill and kill_diags 135
- 4.12 memexer 136
- [number] 137
- 4.13 memtest 138
- Starting address 139
- 4.14 net 143
- <port_name> 144
- 4.15 nettest 145
- 4.16 set sys_serial_num 148
- 4.17 show error 149
- 4.18 show fru 151
- 4.19 show_status 154
- 4.20 sys_exer 156
- 4.21 test 158
- Chapter 5 161
- Error Logs 161
- (Continued 167
- 5.1.3 Bit to Text 168
- Error Logs 5-9 169
- Error Logs 5-11 171
- Error Logs 5-13 173
- Chapter 6 179
- 6.1 System Consoles 180
- Attributes Description 186
- Continued on next page 187
- Continued on next page 188
- >>> init 192
- 6.6 Setting SRM Security 194
- 6.7 Configuring Devices 197
- 6.7.1 CPU Location 198
- 6.7.2 Memory Configuration 199
- Unstacked 200
- A 2 1 7 204
- 2 8 204
- 3 9 204
- 4 10 204
- 6.8 Booting Linux 206
- Chapter 7 209
- Using the Remote 209
- Management Console 209
- 7.1 RMC Overview 210
- RMC Modem 212
- Port (Remote) 212
- 7.2.1 Bypass Modes 214
- 7.3 Terminal Setup 217
- 7.5 Entering the RMC 219
- Field Meaning 223
- 7.11 RMC Command Reference 243
- 7.12 Troubleshooting Tips 252
- Chapter 8 255
- FRU Removal and Replacement 255
- 8.3 Recommended Spares 259
- 8.3.1 Power Cords 261
- 8.4 FRU Locations 262
- 8.5 Removing the Top Cover 264
- 8.6 Removing the Side Panel 266
- 8.7 Replacing the PCI Fan 268
- 8.8 Replacing the CPU Fan 270
- LED is off 276
- V @ >240 284
- V @ >240VA 303
- DIMM Connector Array 305
- 8.23 Replacing the Speaker 314
- Appendix A 327
- A.1 Location of Jumpers 328
- A.2 Function of Jumpers 329
- None Always bypass the RMC 331
- A.3 Setting Jumpers 332
- Appendix B 333
- Isolating Failing DIMMs 333
- (Continued) 343
- B.3 EV68 Single-Bit Errors 344
- Index-1 347
- Index-2 348
- Index-3 349
- Index-4 350
- Index-5 351
- Index-6 352
- Index-7 353
Verwandte Produkte und Handbücher für PC / Workstation Barebones HP Digital AlphaStation 255 Family
(48 Seiten)
(8 Seiten)
(158 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern