Hp RP3440 Bedienungsanleitung Seite 1

HP 9000 rp3410 and HP 9000 rp3440User Service GuideHP Part Number: A7137-96008-ed6Published: February 2010Edition: 6

List of Figures1-1 HP 9000 rp3410 and rp3440 Servers - Front View...191-2 HP 900

Installing Your A6150B Graphics CardIf you ordered the A6150B graphics card kit for installation into a HP 9000 rp3410 or rp3440server, install the gr

Table 3-8 Power StatesDC VoltageApplied?Standby DCVoltageApplied?Power Activated Through the iLO MP PCCommand; or Front Panel Power ButtonActivated?Po

Powering Off the Server Using the iLO MP PC CommandTo power off the server using the iLO MP PC command, follow these steps:1. Gracefully shut down the

1. At the BCH Main Menu, enter Menu> co.2. From the Configuration Menu > prompt, enter pa pri xx/xx/xx.3. From the Configuration Menu> prompt

Verifying the Server Configuration Using Boot Console HandlerTo go the Information Menu, enter in from the BCH Main Menu. Use the corresponding comman

Table 3-10 Server Power Button Functions When Server is On and OS is RunningReactionActionSystem power turns off (software controlled power off)One to

Operating System Boots with ProblemsIf the operating system is running and you are experiencing problems, use the following toolsto help solve the pro

To ensure you have the latest version of the firmware running on the server, download the latestversion of the firmware from the web, and create a CD

Table 3-12 Front Control Panel LED Definitions (continued)DescriptionColorFlash RateStateLED/ButtonWarning: System needs attention. Redundancylost, co

4 Booting the Operating SystemThis chapter describes procedures for booting and shutting down the HP-UX operating systemon the HP 9000 rp3410 and rp34

3-37 Unlocking the Dual Processor Module Locking Mechanism...793-38 Aligning the Processor Module.

To boot HP-UX:1. At the BCH Main Menu, enter Menu> co.2. From the Configuration Menu > prompt, enter pa pri xx/xx/xx.3. From the Configuration M

3. Issue the shutdown command with the appropriate command-line options.The command-line options you specify dictate the way in which HP-UX shuts down

112

5 TroubleshootingThis chapter provides troubleshooting instructions for maintaining your HP 9000 rp3410 orrp3440 server.Troubleshooting MethodologyWAR

Table 5-1 Power Button Functions (continued)ResultSwitch Pressed TimeSystem StateNo effectNot used. This selection initiates E-buzzer functionsthat ar

variety of notification methods, such as e-mail. Event detections are handled automatically withminimal involvement on your part.The following monitor

E - System Event 39 3 % 01 Nov 2004 17:15:03Event Log Navigation Help: + View next block (forward in time, e.

1. Power on the server and insert the ODE CD.2. Boot the system to the PDC prompt (BOOTADMIN, BCH, and so on). PDC prompts candiffer on some computer

Figure 5-1 Control Panel LEDsPower and System LEDsThe power and system LEDs indicate the state of the system. When the system LED is flashingyellow or

Table 5-4 10/100/1000 Base-T Ethernet LAN Connector LEDsDescriptionColorStatusLEDThe 1000 MHz with Ethernet protocol andtwisted-pair wiring is enabled

6-38 Removing the Power Pod...1576-39 Disconn

Figure 5-2 Location of the STBY and BMC LEDsTable 5-6 lists the system board LEDs.Table 5-6 System Board LEDsDescriptionLEDThis standby LED comes on a

Table 5-7 CleaningCleaning ProcedureTime FrameComponentDust with damp, lint-free cloth.RegularlyKeyboardUse the HP Video Screen Cleaning Solution foun

122

6 Removing and Replacing ComponentsThis chapter describes how to remove and replace hardware in HP 9000 rp3410 and rp3440servers.CAUTION: Use care to

Figure 6-1 Internal Physical LayoutTable 6-1 provides the key to Figure 6-1.Table 6-1 Component LocationsHot-pluggable hard disk drives (up to 3)8Powe

Figure 6-2 System Board Connectors and SlotsTable 6-2 provides the key to Figure 6-2.Table 6-2 Connector LocationsPCI backplane connector17Power suppl

Removing and Replacing Server Covers and BezelTo upgrade, remove, or replace most server components, you must first remove the server coversfrom the c

Figure 6-3 Release the Rack Latches3. Slide the server out of the rack until the guide-rail release clips are visible.Inserting the Server Into the Ra

Figure 6-4 Removing the Top Cover on a Rack-Mounted Server3. Lift the top cover off the server chassis.Replacing the Top Cover on a Rack-Mounted Serve

Figure 6-6 Closing the Top Cover on a Rack-Mounted Server3. Slide the server into the rack enclosure and reconnect the power and external cables.Remov

List of Tables1 Publishing History Details...

2. Close the bezel and push toward the front of the server until it locks into place.Figure 6-8 Replacing the Front Bezel on a Rack-Mounted ServerAcce

2. Remove the side cover.a. Grasp both indentations at the top of the side panel and pull outward.b. Lift the side cover off of the server chassis.Fig

3. Remove the top cover.Figure 6-10 Removing the Top Cover on a Pedestal-Mounted Servera. Turn the top cover lock keyswitch to the unlocked position.b

1. Replace the top cover:a. Align the front edge of the top cover with the alignment mark on the optical drive bay.Figure 6-11 Top Cover Alignment Mar

2. Replace the side cover:a. Align the side cover mounting holes with the matching tabs on the server chassis.b. Close the side cover until it snaps o

1. Use the indentation at the top edge of the bezel to pull the bezel away from the chassis andto a 45-degree angle.Figure 6-14 Removing the Front Bez

2. Rotate the bezel against the chassis so that it snaps into place.Removing and Replacing System FansThere are four system fans to keep the server co

2. Remove the fan.To remove fan 1A, 1B, 2 or 3 from a rack-mounted server, or fan 3 from a pedestal server,grasp the appropriate fan and lift it out o

Replacing a System FanTo replace the system fan, follow these steps:1. Grasp the replacement fan module and insert it into its fan socket.2. For fans

Figure 6-19 Releasing the Power Supply Retaining Clip3. Press the power supply release lever down and slide the power supply out of the server.Figure

14

1. Open the power supply release lever and slide the power supply into place.Figure 6-21 Replacing the Power Supply2. Push in on the power supply rele

2. If you have locked your hard drives, you must unlock them before removing or replacinga drive:CAUTION: When the server is running, you must replace

4. Pull outward on the release lever to remove the drive from the server (Figure 6-23;Figure 6-24).Figure 6-24 Removing the Disk DriveReplacing a Hard

Figure 6-25 Removing the Disk Drive Slot Filler4. Insert the hard disk drive into the drive bay from which you removed the drive and pushinward on the

7. Verify the drive replacement and operation by using the system utilities. (For additionalinformation, see Appendix B (page 199) or the HP Integrity

2. Remove the top cover. (See “Removing and Replacing Server Covers and Bezel” (page 126).)3. Grasp the memory airflow guide and lift it out of the se

4. Remove the main portion of the airflow guide:a. Hold the guide using the opening on top of the guide.b. At the same time, grasp the back end of the

5. Remove the front portion of the airflow guide:a. Remove system fans 1A and 1B. (See “Removing a System Fan” (page 136).)b. Remove the memory airflo

Replacing the Processor Airflow GuideTo replace the processor airflow guide, follow these steps:1. Replace the front portion of the airflow guide:a. A

3. Route the processor turbo fan power cables through the processor heatsink posts so that thecables will not be pinched between the heatsink posts an

About This DocumentThis document provides information and instructions on how to service and troubleshoot theHP 9000 rp3410 and rp3440 servers.The doc

• 256 MB• 512 MB• 1 GB• 2 GB• 4 GB (HP 9000 rp3440 only). If 4 GB DIMMs are used, only one configuration (8 X 4 GB inthe first eight sockets) is suppo

1 GB DIMMs. Different size DIMMs can be installed in the server, but all four DIMMs in a quadmust be identical.Memory Loading Rules• DIMMs must be ins

NOTE: When replacing deallocated memory ranks on a server with system firmware version45.11 or greater, you must perform the following procedure befor

• 2A, 2B and 3A, 3B must be an identical quad (2 pairs)• 4A, 4B and 5A, 5B must be an identical quad (2 pairs)• In the HP 9000 rp3440 server, DIMMs mu

Figure 6-34 Inserting the DIMM Into the Connector Socket6. Replace the memory airflow guide. (See “Removing and Replacing the Memory AirflowGuide” (pa

Removing and Replacing a Dual Processor ModuleThis section provides information about installing dual processor modules. The modules arelocated on the

Figure 6-36 Removing the Power Pod Mounting Screws7. Slide the power pod toward the rear of the system board so that the power pod connectordisconnect

Figure 6-38 Removing the Power Pod9. Disconnect the turbo fan power cable.Figure 6-39 Disconnecting the Turbo Fan Cable10. Release the four heatsink c

Figure 6-40 Releasing the Heatsink Captive Screws11. Slide the sequencing retainer plate toward the back of the server to open the hole in the edgeof

13. Lift the dual processor module and the turbo fan assembly up and out of the chassis(Figure 6-42). If protective pin covers are available, install

Appendix B Utilities: Provides information on the utilities on the server such as Boot ConsoleHandler (BCH) and the iLO MP.Appendix C Physical and Env

Installing a Dual Processor ModuleEither one or two dual processor modules are located on the system board. Module #1 is locatedto the right of the sy

Figure 6-45 Aligning the Dual Processor Module7. Use the special processor tool to lock the dual processor module in place on the systemboard. To do t

Figure 6-47 Securing the Captive Screws10. If you are installing a second dual processor module in a server which contained only onedual processor mod

Figure 6-49 Aligning the Processor Module Power Pod12. Align the two mounting screw holes on the power module with the screw holes in the shimson the

Figure 6-50 Installing the Processor Module Power Pod Mounting ScrewsCAUTION: Turbo fan power cables can be damaged if pinched between the heatsink po

Figure 6-52 Connecting the Power Pod Cable16. Replace the processor airflow guide. (See “Replacing the Processor Airflow Guide” (page 148).)17. Replac

3. Remove the memory airflow guide. (See “Removing and Replacing the Memory AirflowGuide” (page 144).)4. Remove the processor airflow guide, the front

6. Verify the battery replacement and operation by using the system utilities. (For additionalinformation, see Appendix B (page 199) or the HP Integri

Figure 6-54 Removing the PCI Card Cage4. Grasp the PCI card cage cover and slide it away from the bulkhead end of the cage, then liftthe cover off.Fig

1. Hold the cover in the mounting position and slide it toward the bulkhead end of the cage.2. Hold the PCI card cage above the chassis mounting posit

Table 2 HP-UX 11i ReleasesSupported Processor ArchitectureRelease NameRelease IdentifierIntel® Itanium®HP-UX 11i v1.5B.11.20Intel ItaniumHP-UX 11i v1.

5. Install a PCI slot cover to close the cavity left by the removal of the PCI card (Figure 6-56).This maintains the proper airflow within the chassis

5. Replace the PCI card cage. (See “Replacing the PCI Card Cage” (page 168).)6. Replace the top cover.7. Verify the PCI card replacement and operation

Figure 6-59 Replacing the PCI Backplane3. Replace any PCI and graphics cards. (See “Replacing a PCI or Graphics Card” (page 170).)4. Replace the PCI c

5. Pull the drive straight out to remove it from the chassis.Figure 6-60 Removing the Removable Media DriveReplacing a Removable Media DriveTo replace

4. Disconnect all the power and external cables.5. Remove the top cover. (See “Removing and Replacing Server Covers and Bezel” (page 126).)6. Unscrew

7. Verify the card replacement and operation by using the system utilities. (For additionalinformation, see Appendix B (page 199) or the HP Integrity

3. Lift up on the battery retaining clip with a flat-head screwdriver and slide the battery outof its socket.CAUTION: Only lift the battery high enoug

2. Remove the top cover. (See “Removing and Replacing Server Covers and Bezel” (page 126).)3. Disconnect the LED status panel controller cable.4. Unsc

• Memory (DIMMs). (See “Removing System Memory” (page 152))• Dual processor modules. (See “Removing a Dual Processor Module” (page 155))• iLO MP card.

Figure 6-66 Removing the System Board Mounting ScrewRemoving and Replacing the System Board 179

HP Contact InformationFor the name of the nearest HP authorized reseller:• In the United States, see the HP US service locator webpage (http://welcome

10. Remove the system board:a. Grasp the memory controller chip heatsink and the processor module heatsink andslide the system board toward the front

1. Grasp the new system board by its edges and carefully align it in the server:a. Angle the board to enable the PCI connector to slide into the PCI c

3. Screw in the system board mounting screw.4. Connect all the cables to their appropriate connectors on the system board.5. Screw in the six rear bac

• Processor airflow guide. (See “Replacing the Processor Airflow Guide” (page 148))• Memory airflow guide. (See “Replacing the Memory Airflow Guide” (

Replacing the Resident System Board with a Replacement System BoardAll A7136B, A9948A, and A9949A products within the documented serial number ranges

Figure 6-73 System Product Number, System Serial Number, Key CertificateReplacing a System BoardYou must perform the following procedure to ensure all

14. Perform the resetting with the changes in effect.CAUTION: If this procedure is not followed, the server components will not be functional.Removing

5. Unscrew the PSI mounting screw and remove the PSI module from the server.Figure 6-75 Removing the Mounting ScrewFigure 6-76 Removing the PSI Interf

1. Place the PSI module into the chassis by sliding the module retaining tab into the socket onthe hard disk drive bay wall.Figure 6-77 Replacing the

6. Verify the PSI replacement and operation by using the system utilities. (For additionalinformation, see Appendix B (page 199) or the HP Integrity a

1 OverviewThe HP 9000 rp3410 server is a 1P/1C, 1P/2C, rack- or pedestal-mount server. Similarly, the HP9000 rp3440 server is a 1P/1C, 1P/2C, 2P/2C, o

Figure 6-80 Disconnecting the SCSI CablesFigure 6-81 Removing the Mounting Screws190 Removing and Replacing Components

7. Remove the hard drive backplane by sliding it in the direction of the arrow and pulling itoutward from its standoff posts.Figure 6-82 Removing the

1. Insert the hard drive backplane onto its four chassis standoffs and slide it to the left as youface it. This locks the hard drive backplane in plac

A Replacement PartsThis appendix provides a replacement parts list that contains the following customer self-repairpart information for the server:• M

Figure A-2 Pedestal and Rack PartsCustomer Self RepairHP products are designed with many Customer Self Repair (CSR) parts to minimize repair timeand a

Based on availability and where geography permits, CSR parts are shipped for next businessday delivery. Same-day or four-hour delivery may be offered

Table A-2 Replaceable Parts List (continued)Customer SelfRepairPart NumberExchangePart NumberReplacementDescriptionItemNo.CYN/AA7231-66530PCI backplan

Table A-2 Replaceable Parts List (continued)Customer SelfRepairPart NumberExchangePart NumberReplacementDescriptionItemNo.NN/A5069-5441Processor Tool

Table A-2 Replaceable Parts List (continued)Customer SelfRepairPart NumberExchangePart NumberReplacementDescriptionItemNo.AYN/AA7231-63004Disk PowerN/

B UtilitiesThis appendix describes the boot console handler (BCH) utility that is part of the server.High-level information is also provided on iLO MP

Legal NoticesCopyright © 2003, 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Th

Figure 1-4 HP 9000 rp3410 and rp3440 Servers - Pedestal MountDetailed Server DescriptionThis section provides information on the features that compris

The boot device paths specify the primary boot device (PRI boot path), the high-availabilityalternate device (HAA boot path), and the alternate device

0/1/1/0.1 0/01/01/0.1 (hex) Alternate boot path: intscsib.2

BOot [PRI|ALT|<path>] Boot from specified path DIsplay Redisplay the current menu HElp [<c

Service MenuThe Service menu commands are used by service personnel to view information about the systemfor the purpose of system service operations.M

204

C Physical and Environmental SpecificationsTable C-1 provides temperature and airflow information for minimum, typical, and maximumconfigurations for

206

IndexAA6150 graphics card, installing, 100airflow guides, remove and replace, 65, 144antistatic wrist strap, 123BbackplanePCI, remove and replace, 171

event ID, 49event IDs, 23event monitoring service (EMS), 115external core, features I/O, 21Ffanssystem, remove and replace, 136featuresexternal core I

DIMMs, 20, 26features, 20installing additional, 70installing DIMMS, 152reallocate, 152removing DIMMS, 152replace deallocated memory rank, 152supported

6 GB (HP 9000 rp3410 server), 24 GB (HP 9000 rp3440 server with 2 GB DIMMs installedin all 12 slots), or—— 32 GB (HP 9000 rp3440 server with 4 GB DIMM

replaceable parts list, 195returning damaged equipment, 52Ssafety information, 50, 123SCSIbackplane, remove and replace, 189connector pinout, 36contro

• 650W output power.• The power supply is split in a front end block (the actual power supply case) that convertsthe line voltage into high DC voltage

Event IDs for Errors and EventsThe server firmware generates event IDs similar to chassis codes for errors, events, and forwardprogress to the Integra

Figure 1-5 System Board Block DiagramSystem Board ComponentsThe following describes the main components of the system board:• Dual PA-RISC processors:

mechanical compatibility and support circuitry exist. A processor CSR consists of a dual processormodule with heatsink assembly.One end of the FSB is

Figure 1-6 Memory Block DiagramMemory ArchitectureThe I/O ASIC memory interface supports two DDR cells, each of which is 144 data bits wide.The memory

Table 1-2 Memory Array CapacitiesDDR SDRAM Count, Type and TechnologySingle DIMM SizeMinimum and MaximumMemory Size18 x 32 MB x 4 DDR SDRAMs (128 MB)2

• 16-bit PDH bus with reserved address space for the following:— Flash memory— Nonvolatile memory— Scratch RAM— Real-time clock— UARTs— External regis

IDE InterfaceThe IDE controller (PCI649) supports the ATAPI zero (0) to five (5) modes (from 16 to 100 MB/s).The usable speed on this system is limite

Table of ContentsAbout This Document...15Intended

Table 1-4 Extended Core I/O Paths (continued)ACPI PathLocationFunction Associated with PathSlot0/0/3/0Rear panel (with LAN10/100 label)LAN 100 portCor

Table 1-6 PCI I/O Hardware Paths (continued)HP-UX PathMAPPER PathPCI Card Functionality0/1/1/1.2.00/1/1/1.2.0Internal SCSI - Slot 20/1/1/00/1/1/0Chann

Figure 1-8 Control Panel LEDs and ButtonsTable 1-7 provides control panel and LED information.Table 1-7 Control Panel LEDs and SwitchesFunctionNameThe

Additional Controls and IndicatorsHP 9000 rp3410 and rp3440 servers can have up to three low-voltage differential (LVD), 3.5-inchform factor hot-plugg

Rear PanelThe rear panel of the HP 9000 rp3410 and rp3440 servers includes communication ports, I/Oports, AC power connector, and the locator LED/butt

10/100/1000 Base-T Ethernet LAN ConnectorFigure 1-12 shows the rear panel 10/100/1000 base-T Ethernet LAN connector and the status andactivity LEDs.Fi

Figure 1-13 Dual USB Port ConnectorFigure 1-14 shows the single USB port.Figure 1-14 Single USB PortTable 1-13 lists the USB pinouts.Table 1-13 USB Pi

Table 1-14 SCSI Port Pinouts (continued)Signal DescriptionPin NumberSignal DescriptionPin NumberS39 (–DB P1)39S5 (+DB P1)5S40 (–DB 0)40S6 (+DB 0)6S41

Figure 1-16 iLO MP Card LAN LEDsTable 1-15 lists the iLO MP card LAN LEDs.Table 1-15 iLO MP Card LAN LEDsDescriptionColorLEDiLO MP is running self-tes

Table 1-17 Power StatesDC VoltageApplied?Standby DCVoltageApplied?Power Activated through the iLO MP PCCommand; or Front Panel Power ButtonActivated?P

Additional Controls and Indicators...33Hot-Pluggable Disk

3. To enable command mode, enter CM.4. To use the remote power control command, enter PC.5. Enter OFF to power off the server, and enter YES when prom

2 System SpecificationsThis chapter provides information on the basic system configuration, physical specifications,and requirements for the HP 9000 r

Table 2-2 Server Dimensions and Values (continued)ValuesDimension0.2 m2(2.1 sq. ft.)Pedestal footprint2URack unitsGroundingThe site building shall pro

System Power SpecificationsAvailable power (output) is the maximum DC power that the power supply can supply to thesystem.Maximum input power is what

Table 2-5 Additional Component Power ConsumptionPower ConsumptionAdditional Component443.6 Btu/h130WProcessor78.4 Btu/h23WSCSI hard disk drive (with I

per 1,000 feet of elevation above 5,000 feet above sea level up to 30°C at 10,000 feet. For optimumreliability and performance, the recommended operat

The air is pulled through openings in the front cover and the mass storage devices and pushedthrough the PCI card cage.Perforation is provided between

3 Installing the SystemThis chapter provides information on how to install the system.IntroductionThe HP 9000 rp3410 server is a 1P/1C, 1P/2C, rack- o

Figure 3-4 HP 9000 rp3410/rp3440 Server - Pedestal MountDetailed Server DescriptionThe following sections list the main subsystems within the HP 9000

Table 3-1 HP 9000 rp3410 and rp3440 Server Features (continued)rp3440rp3410FeaturesIntegrated Ultra-3 SCSI dual-channel controller;80 MBs transfer rat

Unloading the Server with a Lifter...52Installing Addit

Table 3-2 Server Dimensions and Values (continued)ValuesDimensions2.1 sq ft (0.2 m2)Pedestal footprint2URack unitsSafety InformationUse care to preven

Table 3-3 Installation Sequence Checklist (continued)CompletedDescriptionStepSet up the console.5Power on the server.6Access the console.7Boot the ope

NOTE: To identify each item by part number, see the sales order packing slip.Returning Damaged EquipmentIf the equipment is damaged, contact your HP c

instructions, see the Installation Guide, Mid-Weight Slide Kit (HP part number 5065-7291). Thisdocument can be accessed on the HP website at http://ww

Removing the Top Cover on a Rack-Mounted ServerNOTE: If you are replacing a hot-swappable item, you can leave the server on and leave theexternal cabl

1. Align the front edge of the cover with the alignment mark on the optical drive bay.Figure 3-7 Aligning the Top Cover2. Grasp the blue release lever

1. Press in on the retaining clips located on the right side of the front panel.Figure 3-9 Front Bezel Retaining Clip2. Rotate the front panel outward

Accessing a Pedestal-Mounted ServerNOTE: If you are replacing a hot-swappable item, you can leave the server on and leave theexternal cables (includin

Figure 3-12 Removing the Top Cover on a Pedestal-Mounted Server4. Remove the top cover.CAUTION: The server depends on the access panels being closed f

2. Place the top cover on the chassis and slide it toward the front of the server until the bluerelease lever snaps in place.Figure 3-14 Replacing the

Preparation...91Det

Removing and Replacing the Front Bezel on a Pedestal-Mounted ServerYou must remove the front bezel from the chassis to gain access to the power suppli

Figure 3-17 Aligning the Pedestal Front Bezel3. Rotate the bezel against the chassis so that it snaps into place.Installing Internal Hard Disk DrivesT

1. If you will be locking the hard drive in place, you must remove the cover to access the harddrive lock.a. If rack-mounted, slide the server out fro

4. Close the drive ejector handle by pushing it down until it clicks.5. If desired, lock the hard drive in place.a. Press the hard drive locking lever

Installing a DVD DriveInstall a DVD drive behind the front bezel.WARNING! Ensure that the server is powered off and all the power sources have beendis

9. Verify the drive operation by using the system utilities.• Use the iLO MP commands to verify operation.• Use the BCH commands to verify operation.•

3. Grasp the memory airflow guide and lift it out of the server.Figure 3-24 Removing the Memory Airflow GuideReplacing the Memory Airflow GuideTo repl

4. Remove the main portion of the airflow guide:a. Hold the guide using the opening on top of the guide.b. At the same time, grasp the back end of the

8. Rotate the clip clockwise to release the latch.Figure 3-27 Opening the Release Clip9. To disconnect the power cable connected to the guide from the

Replacing the Processor Airflow GuideTo replace the processor airflow guide, follow these steps:1. Replace the front portion of the airflow guide:a. A

Standard HP-UX Booting Using the Boot Console Handler...109Booting HP-UX in Single-User Mode...

Installing Additional System MemoryThe server has 12 memory sockets for installing DDR SDRAM memory modules. System memoryDIMMs are located on the sys

Figure 3-30 DIMM Slot IdentificationInstalling System MemoryWhen adding DIMMs, you must use a minimum of four like-sized DIMMs in the next availablequ

Memory Loading Rules and Performance Guidelines• DIMMs must be installed in server load sequence (the first DIMM must be in the first slot,the second

Installation ProcedureTo install DIMMs, follow these steps:1. Power off the server and disconnect all the power and external cables.2. Remove the serv

10. Verify the memory installation by using the system utilities.• Use the iLO MP commands to verify operation.• Use the BCH commands to verify operat

Figure 3-33 Removing the PCI Card Cage Cover5. Unscrew the bulkhead screw that holds the accessory card holder (if installed) in place.6. The PCI slot

at less than optimum speed. PCI slots are numbered 1 (top of card cage) through 4 (bottom ofcard cage). See the labels on the rear panel of the chassi

is replaced. A power supply can be removed and replaced without turning off the server onservers with two power supplies.CAUTION: Before removing a po

4. Push in on the power supply release lever to lock the retaining clip in place.5. Replace the front bezel. (See “Removing and Replacing the Front Be

5. Unlock the dual processor module locking mechanism using the CPU install tool (2.5 mmdriver or Allen Wrench).a. Insert the tool into the hole that

Replacing a Hard Disk Drive...142Removing and Re

Figure 3-38 Aligning the Processor Module8. Use the special CPU install tool (2.5 mm driver or Allen Wrench) to lock the dual processormodule in place

Figure 3-40 Sliding the Sequencing Retainer Plate10. Screw in the four heatsink captive screws in a crisscross torquing pattern by alternatelytighteni

Figure 3-42 Power Module Shims12. Slide the power pod module on the system board metal mounting bracket so that the powerpod module connector connects

Figure 3-44 Installing the Processor Module Power Pod Mounting Screws14. Connect the power pod cable to the power connector on the system board.Instal

Figure 3-45 Connecting the Power Pod CableCAUTION: Turbo fan power cables can be damaged if pinched between the heatsink postsand the processor airflo

19. Replace the cover. (See “Removing and Replacing the Top Cover on a Rack-Mounted Server”(page 53).)20. Reconnect the power and external cables and

6. Lift up on the battery holder retaining clip with a flat-head screwdriver and slide the batteryinto the holder. The positive (+) terminal of the ba

HP RackHP 9000 entry class servers that are installed into racks are shipped with equipment mountingslides. The Mid-Weight Slide Kit, (HP part number

• LVD/SE SCSI port— The SCSI port is used to attach SCSI external mass storage to the server— Connections to the SCSI board include the external SCSI

Figure 3-48 LAN Ports on the Server RearTo enable general network connectivity for the server, follow these steps:1. Obtain a valid IP address for eac

Removing and Replacing the Hard Disk Drive (SCSI) Backplane...189Removing the Hard Drive Disk SCSI B

Table 3-4 Setup Checklist (continued)XActionStepChoose one of the three methods to configure the LAN for iLOMP access:• DHCP with DNS• ARP Ping• RS-23

Figure 3-49 iLO MP Setup FlowchartPreparationYou must perform the following tasks before you can configure the iLO MP LAN.• Determine the physical acc

LAN drop, IP address, and networking information from that of the port used by the operatingsystem.Table 3-5 lists the appropriate connection method,

TIP: HP recommends using the DHCP and DNS method to simplify access to the iLO MP.When you use DHCP and DNS, you can connect to the iLO MP by typing t

Table 3-7 ARP Ping CommandsDescriptionCommandThis command assigns an IP address to the iLO MP MAC address. This ARP table entry mapsthe MAC address of

1. Ensure the emulation software device is properly configured. The terminal emulation deviceruns software that interfaces with the server. The softwa

2. Log in using the default the iLO MP user name and password (Admin/Admin). The MPMain Menu screen displays.TIP: For security reasons, HP strongly re

a. Access the MP Main Menu.b. Enter CM at the MP> prompt.c. Enter UC at the MP:CM> prompt and follow the prompts to modify default passwords.3.

Interacting With the iLO MP Using the Web GUIWeb browser access is an embedded feature of the iLO MP.The iLO MP has a separate LAN port from the syste

Figure 3-51 Status Summary Page4. Select the web interface functions by clicking the Function tabs at the top of the page. Eachfunction lists options