Hp Command View EVA Software Bedienungsanleitung Seite 83
- Seite / 113
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2. Enter the evaperf fn [short] command.
The fnames.conf file is created. Any friendly name information that exists for the management
servers running HP P6000 Command View and listed in the fnamehosts.conf file is
extracted from HP P6000 Command View and stored in the fnames.conf file, located in
INSTALLROOT.
NOTE: When the short option is used, the virtual disk properties (redundancy, preferred
path, and number of presentations) will not be retrieved and the output of the vd command
will have a hyphen (—) for these columns. To retrieve all the properties, the fn command
should be used without the short option.
Update the fnames.conf file when you make changes to the storage systems. The fnames.conf
file must reside in the directory in which HP P6000 Performance Data Collector was installed.
Mapping worldwide names to friendly names
HP P6000 Performance Data Collector does not map the WWN for virtual disks to the HP P6000
Command View friendly name when the WWN value differs from the unique unit identifier (UUID).
The mismatch of WWN and UUID occurs if:
• The virtual disk has failed over in an HP P6000 Continuous Access environment.
• The WWN of the virtual disk is changed from the default WWN.
To match WWNs and UUIDs:
1. Open the fnames.conf file in a text editor.
2. Identify each virtual disk for which HP P6000 Performance Data Collector is not displaying a
friendly name.
3. Using the HP Storage System Scripting Utility, run the following command for each virtual
disk:
LS VDISK virtual disk name
All information about the virtual disk, including the WWN is displayed.
4. From the command output, copy the WWN for a virtual disk to the corresponding virtual disk
in the fnames.conf file, replacing all lowercase letters with uppercase.
5. Repeat Step 4 for each applicable virtual disk.
6. Save the fnames.conf file.
IMPORTANT: Do not run the command evaperf fn after completing these steps; otherwise,
you will have to repeat the steps.
Adding friendly names manually
You can create and maintain the fnames.conf file manually using a standard text editor.
Each line in the file contains a WWN that uniquely identifies an object and the friendly name of
the object. When reading this file, HP P6000 Performance Data Collector ignores blank lines and
lines that begin with a pound sign (#). The following is a listing from a manually created file:
Using friendly names 83
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Overview 7
- 8 Overview 8
- 4. Browsing computer1. LAN 10
- 5. Hosts2. SAN 10
- 3. HP EVA4400 storage systems 10
- 10 Overview 10
- User interface 11
- Storage systems point of view 12
- Settings point of view 13
- 14 Overview 14
- Internet Protocol support 15
- Password formats 16
- Considerations 17
- License types 20
- Instant-on licenses 20
- Permanent licenses 20
- Data migration licenses 21
- FCIP licenses 21
- Obtaining license keys 22
- Retrieving licenses 23
- Entering license keys 23
- Importing licenses 24
- 4 Provisioning storage 26
- Disk types 27
- Disk group types 27
- General guidelines 27
- Disk group capacity 28
- Redundancy (Vraid) levels 29
- Virtual disks 30
- 32 Provisioning storage 32
- Presentation 33
- Online virtual disk migration 33
- Mirrorclone migration 34
- Thin provisioning 34
- Online Help 35
- 5 Replicating storage 36
- Snapshots 37
- Mirrorclones 38
- Containers 40
- Optimizing snap creation 41
- 42 Replicating storage 42
- DR groups 43
- Creating DR groups 44
- Initializing storage systems 46
- User-initiated service mode 47
- Starting the storage system 48
- Figure 10 HSV450 rear view 49
- Resynchronizing controllers 50
- Hardware 50
- Verifying hardware status 51
- Remote service test 51
- Configuring iSCSI devices 53
- Events overview 55
- Viewing events 56
- Viewing events 57 57
- Configuring host notification 58
- Filtering events by severity 59
- Retrieving the parse file 60
- Sending the event file 62
- Creating page footer messages 63
- Setting audit logging options 64
- Configuring SNMP credentials 66
- Optimizing performance 67
- Using the right-click menu 67
- Failed transceiver 70
- Failed I/O module 70
- Failed blower power supply 70
- Version numbers differ 72
- Performance Data Collector 74
- Events and logs 79
- Logging configuration file 79
- Configuration recommendations 80
- SSL protocol 81
- Prohibited commands 81
- Backward compatibility 81
- Using friendly names 82
- Using friendly names 83 83
- Using short names 84
- Viewing storage systems 85
- Specifying the output 85
- Filtering data 86
- Commands 87
- Command modifiers 89
- Data filtering 92
- Objects and counters 93
- HP EVA virtual disk 94
- HP EVA virtual disk group 95
- HP EVA host connection 96
- HP EVA host port statistics 96
- HP EVA physical disk 96
- HP EVA physical disk group 97
- HP EVA DR tunnels 97
- HP EVA DR Group Information 98
- HP EVA Xcopy Metrics 99
- HP EVA WSame Metrics 99
- HP EVA Unmap Metrics 100
- Contacting HP 101
- Related information 101
- Typographical conventions 102
- 12 Documentation feedback 103
- Event code format 104
- Corrective action codes 105
- Coupled crash control codes 106
- Dump/restart control codes 107
- Glossary 108
- 110 Glossary 110
- 112 Index 112
Verwandte Produkte und Handbücher für Lager Hp Command View EVA Software
Lager Hp XP7 Storage Bedienungsanleitung
(250 Seiten)
(250 Seiten)
(58 Seiten)
(60 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.917 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern