Hp Command View EVA Software Bedienungsanleitung Seite 46
- Seite / 113
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6 Maintaining and managing HP P6000 EVA storage
systems
This chapter describes how to use HP P6000 Command View to maintain the storage systems.
Initializing storage systems
If Insight Remote Support is installed on the management server (server-based management), see
the documentation for instructions on adding entitlement details for the new storage system at:
http://h18023.www1.hp.com/support/svctools/webes/
When you install an array, it appears as an uninitialized storage system. Initializing an array
makes it ready for use, binds the controllers as an operational pair (for storage systems other than
the HP EVA4400 and P6300/P6350/P6500/P6500 EVA), and establishes preliminary data
structures on the storage system. Initializing also sets up the first disk group, which is called the
default disk group. If you are upgrading an existing version of HP P6000 Command View, the
storage systems remain initialized and any other existing components are retained.
When initializing a storage system, you must enter a name for the array.
You can also perform the following optional tasks:
• Enter the number of disks to be included in the default disk group.
• Set the drive type.
• Set the array date and time.
• Enter a console LUN ID.
• Select a disk failure protection level.
• Enter comments.
See the online help for instructions for completing these tasks.
Configure WEBES to generate alerts using Insight Remote Support
After installing Insight Remote Support, you must configure WEBES to generate alerts using Insight
Remote Support. Use the Desta tool to add the host to the Insight Remote Support SNMP list and
then run the commands desta SNMP off and desta SNMP on.
You must configure WEBES to generate alerts using Insight Remote Support if either of the following
situations occur:
• You install Insight Remote Support and the HP P6000 Command View software suite on the
same management server for the first time.
• You observe that events are listed in the Insight Remote Support user interface, but alert
indications are not received through the WEBES client.
To configure WEBES:
1. Open a command view window on the management server.
2. Change to the directory where Insight Remote Support is installed. Typically, the directory is
<install path>\Hewlett-Packard\svctools\common\bin.
3. Enter the following commands at the system prompts:
C:\Program Files\Hewlett-Packard\svctools\common\bin> desta snmp off
Do you really want to turn off SNMP service trap notification [Yes]:
yes
SNMP Service Trap notification is now disabled.
46 Maintaining and managing HP P6000 EVA storage systems
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Overview 7
- 8 Overview 8
- 4. Browsing computer1. LAN 10
- 5. Hosts2. SAN 10
- 3. HP EVA4400 storage systems 10
- 10 Overview 10
- User interface 11
- Storage systems point of view 12
- Settings point of view 13
- 14 Overview 14
- Internet Protocol support 15
- Password formats 16
- Considerations 17
- License types 20
- Instant-on licenses 20
- Permanent licenses 20
- Data migration licenses 21
- FCIP licenses 21
- Obtaining license keys 22
- Retrieving licenses 23
- Entering license keys 23
- Importing licenses 24
- 4 Provisioning storage 26
- Disk types 27
- Disk group types 27
- General guidelines 27
- Disk group capacity 28
- Redundancy (Vraid) levels 29
- Virtual disks 30
- 32 Provisioning storage 32
- Presentation 33
- Online virtual disk migration 33
- Mirrorclone migration 34
- Thin provisioning 34
- Online Help 35
- 5 Replicating storage 36
- Snapshots 37
- Mirrorclones 38
- Containers 40
- Optimizing snap creation 41
- 42 Replicating storage 42
- DR groups 43
- Creating DR groups 44
- Initializing storage systems 46
- User-initiated service mode 47
- Starting the storage system 48
- Figure 10 HSV450 rear view 49
- Resynchronizing controllers 50
- Hardware 50
- Verifying hardware status 51
- Remote service test 51
- Configuring iSCSI devices 53
- Events overview 55
- Viewing events 56
- Viewing events 57 57
- Configuring host notification 58
- Filtering events by severity 59
- Retrieving the parse file 60
- Sending the event file 62
- Creating page footer messages 63
- Setting audit logging options 64
- Configuring SNMP credentials 66
- Optimizing performance 67
- Using the right-click menu 67
- Failed transceiver 70
- Failed I/O module 70
- Failed blower power supply 70
- Version numbers differ 72
- Performance Data Collector 74
- Events and logs 79
- Logging configuration file 79
- Configuration recommendations 80
- SSL protocol 81
- Prohibited commands 81
- Backward compatibility 81
- Using friendly names 82
- Using friendly names 83 83
- Using short names 84
- Viewing storage systems 85
- Specifying the output 85
- Filtering data 86
- Commands 87
- Command modifiers 89
- Data filtering 92
- Objects and counters 93
- HP EVA virtual disk 94
- HP EVA virtual disk group 95
- HP EVA host connection 96
- HP EVA host port statistics 96
- HP EVA physical disk 96
- HP EVA physical disk group 97
- HP EVA DR tunnels 97
- HP EVA DR Group Information 98
- HP EVA Xcopy Metrics 99
- HP EVA WSame Metrics 99
- HP EVA Unmap Metrics 100
- Contacting HP 101
- Related information 101
- Typographical conventions 102
- 12 Documentation feedback 103
- Event code format 104
- Corrective action codes 105
- Coupled crash control codes 106
- Dump/restart control codes 107
- Glossary 108
- 110 Glossary 110
- 112 Index 112
Verwandte Produkte und Handbücher für Lager Hp Command View EVA Software
Lager Hp XP7 Storage Bedienungsanleitung
(250 Seiten)
(250 Seiten)
(58 Seiten)
(60 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.927 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern