Hp Command View EVA Software Bedienungsanleitung Seite 77
- Seite / 113
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
For object types not listed in Table 3 (page 77), retrieval by object_id is not supported and the
command will show an error message if object_id is specified.
Table 3 HP P6000 Performance Data Collector object_id values
How to specify the object_idObject_type value
Virtual disk UUID or friendly nameVd
Physical disk WWNPd
Disk group numberVdg
Disk group numberPdg
Host port (FP1/FP2/FP3/FP4)Hps
Last 8 characters of the Host's Port ID in the form XXXX-XXXXHc
Host port (FP1/FP2/FP3/FP4)Drt
Virtual disk UUID or friendly namestate_vdisk
Disk group IDstate_diskgroup
Disk WWNstate_disk
DRM group ID or friendly namestate_drm
Array WWN or friendly namestate_array
You can use the following HP P6000 Performance Data Collector CLI options with the above
command: -csv, -tsv, -nh, -KB, -us, -nfn, -fo, -ts2, -fnid, -fd, -cn.
You cannot use the following HP P6000 Performance Data Collector CLI options with the above
command: -sz, -fvd, -cont, -dur, -ts1, -nots, -od, -tlc
Configuring the HP P6000 Command View server
The command to configure HP P6000 Command View access credentials is:
evaperf cvconfig server_name port username
where:
• server_name is the IP address or hostname of the system where HP P6000 Command View
is running
• port is the HP P6000 Command View port (usually 2372). No defaults are assumed here;
you must specify the port number exactly.
• username is the HP P6000 Command View user name (the specified user should be a member
of HP Storage Admins or HP Storage Users)
HP P6000 Performance Data Collector prompts you for a password.
Note that:
• This command accepts the HP P6000 Command View access information provided as is. It
does not validate the information by connecting to the specified HP P6000 Command View.
To verify whether the provided information can be used to communicate with the specified HP
P6000 Command View, another command is provided.
• This command results in the overwriting of any previously configured HP P6000 Command
View access information.
• The HP P6000 Performance Data Collector data collection service does not use the credentials
passed through this command immediately. A service restart is required for the new credentials
to be used for state data collection. After service restart, the newly configured credentials are
used. The same access credentials are used by the server until it is changed by the user,
HP P6000 Performance Data Collector server side logging of performance and state data 77
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Overview 7
- 8 Overview 8
- 4. Browsing computer1. LAN 10
- 5. Hosts2. SAN 10
- 3. HP EVA4400 storage systems 10
- 10 Overview 10
- User interface 11
- Storage systems point of view 12
- Settings point of view 13
- 14 Overview 14
- Internet Protocol support 15
- Password formats 16
- Considerations 17
- License types 20
- Instant-on licenses 20
- Permanent licenses 20
- Data migration licenses 21
- FCIP licenses 21
- Obtaining license keys 22
- Retrieving licenses 23
- Entering license keys 23
- Importing licenses 24
- 4 Provisioning storage 26
- Disk types 27
- Disk group types 27
- General guidelines 27
- Disk group capacity 28
- Redundancy (Vraid) levels 29
- Virtual disks 30
- 32 Provisioning storage 32
- Presentation 33
- Online virtual disk migration 33
- Mirrorclone migration 34
- Thin provisioning 34
- Online Help 35
- 5 Replicating storage 36
- Snapshots 37
- Mirrorclones 38
- Containers 40
- Optimizing snap creation 41
- 42 Replicating storage 42
- DR groups 43
- Creating DR groups 44
- Initializing storage systems 46
- User-initiated service mode 47
- Starting the storage system 48
- Figure 10 HSV450 rear view 49
- Resynchronizing controllers 50
- Hardware 50
- Verifying hardware status 51
- Remote service test 51
- Configuring iSCSI devices 53
- Events overview 55
- Viewing events 56
- Viewing events 57 57
- Configuring host notification 58
- Filtering events by severity 59
- Retrieving the parse file 60
- Sending the event file 62
- Creating page footer messages 63
- Setting audit logging options 64
- Configuring SNMP credentials 66
- Optimizing performance 67
- Using the right-click menu 67
- Failed transceiver 70
- Failed I/O module 70
- Failed blower power supply 70
- Version numbers differ 72
- Performance Data Collector 74
- Events and logs 79
- Logging configuration file 79
- Configuration recommendations 80
- SSL protocol 81
- Prohibited commands 81
- Backward compatibility 81
- Using friendly names 82
- Using friendly names 83 83
- Using short names 84
- Viewing storage systems 85
- Specifying the output 85
- Filtering data 86
- Commands 87
- Command modifiers 89
- Data filtering 92
- Objects and counters 93
- HP EVA virtual disk 94
- HP EVA virtual disk group 95
- HP EVA host connection 96
- HP EVA host port statistics 96
- HP EVA physical disk 96
- HP EVA physical disk group 97
- HP EVA DR tunnels 97
- HP EVA DR Group Information 98
- HP EVA Xcopy Metrics 99
- HP EVA WSame Metrics 99
- HP EVA Unmap Metrics 100
- Contacting HP 101
- Related information 101
- Typographical conventions 102
- 12 Documentation feedback 103
- Event code format 104
- Corrective action codes 105
- Coupled crash control codes 106
- Dump/restart control codes 107
- Glossary 108
- 110 Glossary 110
- 112 Index 112
Verwandte Produkte und Handbücher für Lager Hp Command View EVA Software
Lager Hp XP7 Storage Bedienungsanleitung
(250 Seiten)
(250 Seiten)
(58 Seiten)
(60 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern