HP xw8600 Workstation Spezifikationen Seite 46
- Seite / 180
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ROM Flash
Your HP workstation comes with a programmable flash ROM. By establishing a setup password in the
Computer Setup (F10) Utility, you can protect the ROM from being inadvertently updated or overwritten.
This function is important to ensure the operating integrity of the workstation.
To upgrade the ROM, download the latest SoftPaq images from
http://www.hp.com//support/files.
For maximum ROM protection, establish a setup password. The setup password prevents unauthorized
ROM upgrades. SSM enables you to create the setup password on several workstations simultaneously.
For more information, see
http://www.hp.com/go/ssm.
Remote ROM Flash
Remote ROM Flash allows system administrators to safely upgrade the ROM on remote HP
workstations from a centralized network management console, resulting in a consistent deployment of,
and greater control over, HP PC ROM images over the network.
To use Remote ROM Flash, the workstation must be powered on, or turned on using Remote Wakeup.
For more information about Remote ROM Flash, see the HP Client Manager Software or System
Software Manager sections at
http://www.hp.com/go/ssm.
HPQFlash
The HPQFlash utility is used to locally update or restore the system ROM on PCs using a Windows
operating system.
For more information about HPQFlash, see
http://www.hp.com/go/ssm, and enter the name of your
workstation.
F10 setup instruction in the BIOS SoftPaq
FailSafe Boot Block ROM
The FailSafe Boot Block ROM enables system recovery in the unlikely event of a ROM flash failure. For
example, if a power failure occurs during a ROM upgrade, the Boot Block uses a flash-protected section
of the ROM to verify a valid system ROM flash when power is restored to the system.
If the system ROM is valid, the system starts normally.
If the system ROM fails the validation check, the FailSafe Boot Block ROM provides enough support to
start the system from a BIOS image CD created from a SoftPaq. The BIOS image CD programs the
system ROM with a valid image.
When Boot Block detects an invalid system ROM, the workstation power LED blinks red eight times and
the workstation beeps eight times; then the workstation pauses for two seconds. On some models, a
Boot Block recovery mode message appears.
In preparation for system recovery, use the BIOS CD media file in the SoftPaq to create a BIOS image
CD.
To recover the system after it enters Boot Block recovery mode:
1. If there is media in the diskette or optical drives, remove it.
2. Insert a BIOS image CD into the CD drive.
You can also use USB media such as an HP DriveKey.
36 Chapter 3 System management ENWW
- HP xw8600 Workstation 1
- Table of contents 3
- 1 Product overview 11
- System board architecture 12
- Workstation components 12
- ENWW Product features 3 13
- Front panel components 14
- Rear panel components 15
- Maximizing airflow 16
- Workstation specifications 17
- Power supply specifications 18
- System fans 19
- ENERGY STAR Qualification 20
- HP Cool Tools 22
- Configuring the software 23
- Selecting a language 23
- Creating recovery disks 24
- Ordering backup software 25
- The RestorePlus! process 27
- Protecting your software 30
- Setting up Red Hat Linux 30
- Linux-enabled workstations 32
- 3 System management 33
- BIOS ROM 34
- Workstation management 41
- Installing a remote system 42
- Replicating the setup 43
- HP Client Manager Software 44
- System Software Manager 45
- Proactive Change Notification 45
- Subscriber’s Choice 45
- ROM Flash 46
- Asset tracking and security 47
- Password security 48
- DriveLock 51
- Cable lock (optional) 54
- Drive Protection System 54
- ECC fault prediction 54
- Dual-state power button 55
- Warnings and cautions 57
- Service considerations 58
- Table 4-1 Static electricity 59
- Grounding the work area 60
- Cables and connectors 61
- Hard drives 61
- Lithium coin cell battery 61
- Customer Self-Repair 62
- Predisassembly procedures 62
- System board components 62
- Disassembly order 63
- Removing the cable lock 66
- Side access panel 67
- Removing the Hood Sensor 68
- Front bezel 69
- Bezel blanks 70
- Power button assembly 73
- Optical drive 74
- Removing an optical drive 75
- Installing an optical drive 76
- System speaker 78
- Power supply 79
- Installing the power supply 80
- Memory general information 82
- System board memory 84
- Memory riser assembly 87
- PCI card slots 95
- Slot lane redirection 96
- PCI card support 100
- Installing a PCI card support 101
- PCI Express cards 102
- Installing a PCI Express card 104
- PCI card 105
- Removing the battery 106
- SAS hard drive 107
- Installing a SAS hard drive 108
- SATA hard drive 111
- Installing a SATA hard drive 112
- Processor heatsink 116
- System processor 118
- Installing a system processor 119
- System board 120
- Removing the system board 121
- Product recycling 122
- 5 System diagnostics and 123
- Diagnostic LED codes 124
- ENWW Customer Self Help 115 125
- Solving minor problems 126
- ENWW Customer Self Help 117 127
- Solving power supply problems 128
- Solving diskette problems 130
- ENWW Customer Self Help 121 131
- Solving hard drive problems 132
- Solving display problems 133
- Solving audio problems 135
- Solving printer problems 136
- ENWW Customer Self Help 127 137
- Solving network problems 139
- Solving memory problems 140
- Solving processor problems 141
- Solving DVD problems 141
- ENWW Customer Self Help 133 143
- Troubleshooting checklist 144
- LED color definitions 144
- Key features and benefits 145
- Theory of operation 145
- Diagnostic utility on CD 145
- User Interface 146
- Status tab 147
- POST error messages 148
- ENWW POST error messages 139 149
- ENWW POST error messages 141 151
- ENWW POST error messages 143 153
- 6 Configuring RAID devices 155
- SAS RAID 0 configuration 156
- SAS RAID 1 configuration 156
- Configuring SATA RAID devices 157
- Attaching SATA HDDs 158
- Configuring system BIOS 158
- Creating RAID volumes 159
- Deleting RAID volumes 159
- Resetting the password jumper 162
- A Appendix A—Connector pins 165
- B Appendix B—System board 177
- C Appendix C—Routine care 179
- Cleaning the monitor 180
- Cleaning the mouse 180
Verwandte Produkte und Handbücher für PC / Workstation Barebones HP xw8600 Workstation
(4 Seiten)
(92 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.248 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern