Hp ProLiant DL380e Gen8 Server Bedienungsanleitung Seite 56
- Seite / 142
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Hardware options installation 56
Fan population guidelines
Configuration Fan bay 1 Fan bay 2 Fan bay 3 Fan bay 4 Fan bay 5 Fan bay 6
One processor,
nonredundant
Blank Fan Blank Fan Fan Fan
One processor, redundant
Fan Fan Blank Fan Fan Fan
Two processor, nonredundant
Fan Fan Fan Fan Fan Blank
Two processor, redundant
Fan Fan Fan Fan Fan Fan
• In a redundant fan mode:
o If one fan fails, the system continues to operate without redundancy. This condition is indicated by
a flashing amber Health LED.
o If two fans fail, the system shuts down.
• The minimum fan requirement to make this server bootable is four fans in bays 2, 4, 5, and 6.
Installing a hot-plug fan module if the server is installed in a
ball-bearing rail system with the cable management arm
CAUTION: To prevent the potential for thermal damage and system shutdown, ensure that a
functioning server has all feature bays populated with the required component or blank and the
access panel is installed within 60 seconds of being serviced.
1. Pull down the quick release levers on each side of the server.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is
adequately stabilized before extending a component from the rack.
2. Extend the server on the rack rails until the server rail-release latches engage.
If the server does not extend from the rack, use a T-25 Torx screwdriver to loosen the screws located
within the lever housing.
3. Open the latch, slide the access panel to the rear of the chassis, and then remove the access panel.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- • 8+8-bay SFF drive model 8
- • 12-bay LFF drive model 8
- • 25-bay SFF drive model 8
- Front panel LEDs and buttons 9
- Rear panel components 10
- Item Description 11
- Rear panel LEDs and buttons 12
- System board components 13
- DIMM slot locations 14
- System maintenance switch 14
- Drive numbering 15
- Drive LED definitions 16
- FBWC module LED definitions 17
- Fan locations 19
- Operations 20
- Remove the access panel 23
- Install the access panel 24
- Remove the air baffle 24
- Install the air baffle 24
- Remove the PCI riser cages 25
- Install the PCI riser cages 26
- Optimum environment 28
- Temperature requirements 29
- Power requirements 30
- Server warnings and cautions 31
- Rack warnings 32
- Installing hardware options 33
- Registering the server 35
- Introduction 36
- Security bezel option 36
- Drive options 36
- Installing a hot-plug drive 37
- Rear drive cage options 38
- Drive cable options 46
- Mini-SAS cable option 47
- Mini-SAS Y-cable options 48
- Controller options 49
- Optical drive option 54
- Hot-plug fan module option 55
- Fan population guidelines 56
- 4. Do one of the following: 57
- Memory options 60
- HP SmartMemory 61
- DIMM identification 62
- Memory protection modes 63
- Memory population guidelines 64
- Installing a DIMM 66
- Processor option 67
- Expansion board options 72
- GPU power cable option 74
- Cabling 83
- 4 SFF SATA cabling 84
- 6 LFF SATA cabling 84
- 6 SFF SATA cabling 85
- 8 LFF cabling 85
- 8 SFF cabling 87
- 8+8 SFF cabling 89
- 12 LFF cabling 92
- 25 SFF cabling 94
- 2 LFF rear drive cabling 95
- 2 SFF rear drive cabling 96
- Capacitor pack cabling 97
- Cabling 98 98
- Optical drive cabling 99
- GPU power cabling 99
- Dual-rank GPU 100
- Primary GPU power cabling 100
- Secondary GPU power cabling 101
- Server mode 102
- HP product QuickSpecs 102
- HP iLO Management 102
- Active Health System 103
- Intelligent Provisioning 104
- HP Insight Diagnostics 105
- Erase Utility 105
- HP Insight Online 106
- HP Service Pack for ProLiant 107
- HP ROM-Based Setup Utility 108
- Boot options 109
- Configuring AMP modes 109
- Utilities and features 110
- ROMPaq utility 111
- Automatic Server Recovery 111
- USB support 111
- Keeping the system current 112
- Version control 113
- ProLiant servers 113
- Troubleshooting 115
- System battery replacement 116
- Regulatory information 118
- Electrostatic discharge 119
- Specifications 120
- Specification Value 122
- Support and other resources 126
- Customer Self Repair 128
- Reparo feito pelo cliente 130
- Acronyms and abbreviations 134
- Documentation feedback 138
- Index 139 139
- Index 140 140
- Index 141 141
- Index 142 142
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant DL380e Gen8 Server
(110 Seiten)
(82 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern