Hp ESL E-series Tape Libraries Bedienungsanleitung Seite 52
- Seite / 141
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4. Power on the power switch (see Figure 27).
NOTE:
The library requires several minutes to power on. Nothing displays on the OCP for the
firstfewminutesofthisprocess.
Placing the library on-line or off-line
To place the library on- or off-line:
1. With the library powered on, p ress the Ops button on the O CP to access the Operations screen.
2. Select Ca binet and use the Up and Down arrows to take the library off-line or place it on-line.
For more information on the Operations screen, see Operations screen.
Powering off the library
To power off the library:
1. Place the library off-line, see Placing the library on-line or off-line.
The library robotics completes any current com m a nds and then stops.
2. Verify that the OCP display indicates “Off-line” from the Operations screen.
3. Verify that the media picker is empty.
4. Verify that no backups are in process.
5. Turn off the power switch located on the front of the library (see Figure 27).
6. Wait for the library to complete the shutdown process. (This usually takes 30 seconds, but may
take up to two minutes.)
7. Open the back door of the library cabinet and flip the breaker switches to the off position (left).
The breaker switches are on the power distribution unit located on the bottom left side of the
library cabinet.
NOTE:
When powering off the library, ensure that the two breaker switches on the power
distribution unit are in the off (left) position.
Using the OCP
The OCP is located on the front of the library. The menus on the OCP a llow you to obtain information
about the library, execute library commands, and test library functions.
The status bar a t the top of the OCP displays library status at all tim es, at the left of the bar. The status
can be Online, Going Online,orOffline, followed by a warning level: OK, Warning, or Critical.
In addition, when a library firmware upgrade is in progress, Upgrading FW is displayed on the right
side of the status bar.
NOTE:
If the library reports a status of Warning or Critical, check the Health Status screen to see which
component is causing that status. See Viewing library health status information (standalone libraries
only) for details.
52
Library operations
- HP StorageWorks 1
- ESL E-Series Ta 1
- Legal and notice information 2
- Contents 3
- About this guide 11
- HP technical support 12
- Subscription service 12
- Other HP web sites 12
- HP-authorized reseller 12
- 1Libraryoverview 13
- Back panel 14
- Library robotics 16
- Switch for the i 18
- Tape drives 18
- Tape cartridges 19
- Ultrium tape ca 20
- Load ports and magazines 21
- Card cage and controllers 22
- 1 2 3 4 5 6 8 24
- 1 2 3 4 5 6 7 8 9 24
- L A N-free backup and restore 26
- SCSI over IP Protocol (SIPP) 27
- Interface Manager card 27
- Cross Linked libraries 29
- Space requirem 30
- System components 30
- #1 Phillips screws 31
- Lock Element Addressing 32
- Ultrium library 36
- SDLT library 38
- Mixed media library 40
- Library overview 42
- 2 Lib rary operations 43
- WARNING! 44
- Preparing tape cartridges 45
- Ultrium bar code labels 46
- SDLT ba r cod e labels 47
- Media label identifiers 48
- Setting the writ 49
- Inserting tape cartridges 50
- Powering on the library 51
- Using the OCP 52
- Home screen 53
- OCP buttons 54
- OCP components 55
- Menu screen 57
- Library operations 58
- View ing 61
- Viewing the event log 64
- Load Ports screen 65
- Operations screen 66
- Using removable magazines 70
- Insert removable magazines 71
- Remove re 72
- Start-up problems 73
- OCP problems 74
- Robotics problems 74
- Operating problems 75
- Switch problems 76
- Tape drive problems 77
- Status LED diagnostic codes 78
- Networklinkactivity/speedLEDs 78
- Interface Ma 79
- LED indicators 80
- 5678 3 1 81
- 5678 4 3 2 1 81
- Basic troubleshooting 82
- Verifying SCSI b 83
- Maintaining tap 85
- Cleaning Ultrium tape drives 86
- A Library characteristics 87
- Environmental speci fications 88
- Library characteristics 90
- B Rel ocating the library 91
- Removing tape car tridges 92
- (see Figure 58) 93
- 5. Insta 94
- 6. Instal 95
- Disconnecting library cables 99
- Crating the library 100
- Preparing the li 102
- C Regulatory sta temen ts 103
- Laser sta 104
- Luokan 1 laserlaite 105
- Laser klasse 1 105
- Appareil à laser de classe 1 105
- Producto láser de clase 1 105
- Battery stateme 106
- Waste Electr 107
- Regulatory statements 108
- D Sense data values 113
- ASC ASCQ 114
- Message name / description 114
- Messag e name / description 115
- EEventreporting 123
- Event ID 124
- Critical events 124
- Warning event 126
- Table 24 Warning events 127
- Warning events 127
- Informatio 128
- Table 25 Information events 129
- Information event 129
- Event reporting 134
- Glossary 135
Verwandte Produkte und Handbücher für Lager Hp ESL E-series Tape Libraries
Lager Hp X500 Data Vault Bedienungsanleitung
(331 Seiten)
(331 Seiten)
Lager Hp XP7 Storage Bedienungsanleitung
(208 Seiten)
(208 Seiten)
Lager Hp XP P9500 Storage Bedienungsanleitung
(116 Seiten)
(116 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern