Hp ESL E-series Tape Libraries Bedienungsanleitung Seite 29
- Seite / 141
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
IP IP IP
Library 1 Library 2 Library 3
Management Station
10056
Figure 13 Multipl e libraries conn ected to a single man agement station
NOTE:
IfyouarerunningCommandViewTLversion2.0orlater,youcaninstallCommandViewTLonmultiple
servers (management stations) and manage the library with more than one management station at the
same time. If you are running an earlier version of Command View TL, HP recommends that you install
Command View TL on a sing le dedicated server (management station) on the LAN. However, it is
possible to install Command View TL on multiple servers. In this scenario, if one management station
claims a library for management, then that same library cannot be managed by any other management
station. A library ca n only be managed by one management station at a time.
Cross Linked libraries
A Cross Linked library is two to five library cabinets joined tog ether by hardware, software, and firmware
to function as a s ingle high-capacity library. The Cross Link Kit connects a designated primary cabinet
with another cabinet, which is called a secondar y cabinet. Each Cross Link Expansion kit connects
another secondary cabinet to the system. The entire system is then referred to as a library. Specific
differences between primary and secondary cabinets are explained in this section.
Cross Link cabinets functionality
The primary cabinet controls the robotics of the secondary cabinets. The primary cabinet functions much
like a normal tape library, but it also retrieves data tapes from, sends data tapes to, and assigns storage
locations in the secondary cabinets. To do this, the OCP of a primary cabinet has functionality in
addition to that of a standalone librar y.
Secondary cabinets function mainly as storage units for the Cross Linked library. Their robotics are
controlled by the primar y cabinet. Sec ondary cabinets have very limited o ptions on the OCP.
OCPs for a ll three types of cabinets (standalone, primary, and secondary) are presented in Operator
control panel (OCP).
NOTE:
In all other ways, the Cross Linked library has the same capabilities as a standalone system. Any
differences in the operation of a Cross Linked library are noted in this guide.
HP StorageWorks
29
- HP StorageWorks 1
- ESL E-Series Ta 1
- Legal and notice information 2
- Contents 3
- About this guide 11
- HP technical support 12
- Subscription service 12
- Other HP web sites 12
- HP-authorized reseller 12
- 1Libraryoverview 13
- Back panel 14
- Library robotics 16
- Switch for the i 18
- Tape drives 18
- Tape cartridges 19
- Ultrium tape ca 20
- Load ports and magazines 21
- Card cage and controllers 22
- 1 2 3 4 5 6 8 24
- 1 2 3 4 5 6 7 8 9 24
- L A N-free backup and restore 26
- SCSI over IP Protocol (SIPP) 27
- Interface Manager card 27
- Cross Linked libraries 29
- Space requirem 30
- System components 30
- #1 Phillips screws 31
- Lock Element Addressing 32
- Ultrium library 36
- SDLT library 38
- Mixed media library 40
- Library overview 42
- 2 Lib rary operations 43
- WARNING! 44
- Preparing tape cartridges 45
- Ultrium bar code labels 46
- SDLT ba r cod e labels 47
- Media label identifiers 48
- Setting the writ 49
- Inserting tape cartridges 50
- Powering on the library 51
- Using the OCP 52
- Home screen 53
- OCP buttons 54
- OCP components 55
- Menu screen 57
- Library operations 58
- View ing 61
- Viewing the event log 64
- Load Ports screen 65
- Operations screen 66
- Using removable magazines 70
- Insert removable magazines 71
- Remove re 72
- Start-up problems 73
- OCP problems 74
- Robotics problems 74
- Operating problems 75
- Switch problems 76
- Tape drive problems 77
- Status LED diagnostic codes 78
- Networklinkactivity/speedLEDs 78
- Interface Ma 79
- LED indicators 80
- 5678 3 1 81
- 5678 4 3 2 1 81
- Basic troubleshooting 82
- Verifying SCSI b 83
- Maintaining tap 85
- Cleaning Ultrium tape drives 86
- A Library characteristics 87
- Environmental speci fications 88
- Library characteristics 90
- B Rel ocating the library 91
- Removing tape car tridges 92
- (see Figure 58) 93
- 5. Insta 94
- 6. Instal 95
- Disconnecting library cables 99
- Crating the library 100
- Preparing the li 102
- C Regulatory sta temen ts 103
- Laser sta 104
- Luokan 1 laserlaite 105
- Laser klasse 1 105
- Appareil à laser de classe 1 105
- Producto láser de clase 1 105
- Battery stateme 106
- Waste Electr 107
- Regulatory statements 108
- D Sense data values 113
- ASC ASCQ 114
- Message name / description 114
- Messag e name / description 115
- EEventreporting 123
- Event ID 124
- Critical events 124
- Warning event 126
- Table 24 Warning events 127
- Warning events 127
- Informatio 128
- Table 25 Information events 129
- Information event 129
- Event reporting 134
- Glossary 135
Verwandte Produkte und Handbücher für Lager Hp ESL E-series Tape Libraries
Lager Hp X500 Data Vault Bedienungsanleitung
(331 Seiten)
(331 Seiten)
Lager Hp XP7 Storage Bedienungsanleitung
(208 Seiten)
(208 Seiten)
Lager Hp XP P9500 Storage Bedienungsanleitung
(116 Seiten)
(116 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern