HP 220mx Betriebsanweisung Seite 222
- Seite / 378
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Jukebox SCSI-2 Command Set
Send Diagnostic Command (1DH)
Chapter 3 3-35
Jukebox SCSI-2 CommandsJukebox SCSI-2 Commands
Send Diagnostic Command (1DH)
This command causes the library to perform certain predefined
diagnostic test/exercise routines.
The Request Sense (Table 3-5 on page 3-8) and the Receive Diagnostic
Results (Table 3-29 on page 3-33) commands can be used to get the
results of a test.
SelfTst When set to 1, the Poweron Selftest runs. This selftest
is equivalent to running Test Sequence 1, the Poweron
Sequence. The parameter list length must be 0.
When set to 0, the diagnostic specified in the parameter
list is run.
DevOfL Must be set to 1 for any test other than Selftest.
UnitOfl Must be set to 1 for any test other than Selftest.
Parameter List
Length The number of parameter bytes in the Data Out Phase
that describes the test to be run. The valid range is
between 2 and 10, although this value must be 0 if the
Selftest bit is set to 1. See Table 3-32 on page 3-36.
Table 3-31 Send Diagnostic Command CDB
Byte 7 6 5 4 3 2 1 0
0 Operation Code (1DH)
1 Logical Unit Number
(0)
Reserved (0) SelfTst DevOfL UnitOfl
2 Reserved (0)
3 Parameter List Length (MSByte)
4 Parameter List Length (LSByte)
5 Control Byte (0)
- Command Reference 2
- Revision History 3
- Typographical Conventions 4
- In This Manual 5
- Contents 10
- 1 SCSI Command Overview 20
- Drive Control Commands 22
- Good 00H 33
- Check Condition 02H 33
- Condition Met 04H 33
- Busy 08H 34
- Intermediate/Good 10H 34
- Reservation Conflict 18H 34
- Queue Full 28H 34
- Conditions 35
- 2 SCSI-2 Drive Command Set 38
- Flag, Link, and RelAdr 44
- Test Unit Ready Command (00H) 45
- Sense Data Format 48
- Field Pointer Types 50
- Format Unit Command (04H) 52
- Reassign Blocks Command (07H) 56
- Read (Group 0) Command (08H) 58
- Write (Group 0) Command (0AH) 60
- Seek (Group 0) Command (0BH) 62
- Mode Select Command (15H) 68
- Mode Select Header 70
- Read-Write Error Recovery 71
- Disconnect-Reconnect 73
- Caching Page 08H 74
- Control Mode Page 0AH 76
- Vendor Unique Format Page 20H 79
- Format Mode 03H 80
- Vendor Unique Page 21H 83
- DIP Switch Locations 88
- Read-Write Error Recover Page 94
- Disconnect-Reconnect Page 02H 96
- Control Mode Page (0AH) 100
- Medium Types 101
- SCSI-2 Drive Commands 102
- Vendor Unique 103
- Format Mode 104
- Read Capacity Command (25H) 117
- Read (Group 1) Command (28H) 119
- Seek (Group 1) Command (2BH) 124
- Pre-Fetch (34H) 131
- Synchronize Cache (35H) 132
- Write Buffer Command (3BH) 136
- Read Buffer Command (3CH) 139
- Read Long Command (3EH) 141
- Write Long Command (3FH) 143
- Log Select Command (4CH) 146
- Parameter List Data 147
- Log Sense Command (4DH) 148
- Supported Log Pages 00H 149
- Read (Group 5) Command (A8H) 165
- Read Long Command (DEH) 182
- Write Long Command (DFH) 184
- SCSI-2 Drive Command Set 187
- Chapter 22-150 187
- 3 Jukebox SCSI-2 Command Set 188
- Numerical List of Commands 189
- Alphabetical List of Commands 191
- Rezero Unit Command (01H) 194
- Request Sense Command (03H) 195
- Rotate Mailslot Command (0CH) 200
- Inquiry Command (12H) 201
- Inquiry Command Data 202
- Vital Product Data Pages 203
- Reserve Command (16H) 205
- Release Command (17H) 207
- Mode Sense Command (1AH) 208
- Transport Element (Picker) 212
- Device Capabilities 213
- Send Diagnostic Command Data 223
- Error Logs Table Format 236
- Move Success Log Table Format 240
- Force Log Data Format 241
- Recovery Log Data Format 242
- Drive Log Data Format 244
- Odometer Log Data Format 245
- Run-Time Log Data Format 246
- Retry Log Data Format 248
- Move History Log Data Format 250
- Move Medium Command (A5H) 251
- Read Element Status Data 256
- A Drive Error Codes 264
- Chapter Overview 265
- Drive Error Codes 266
- Internal Error Codes 272
- DSP Error Codes 282
- Drive Error Codes 287
- Appendix AA-24 287
- B Autochanger Error Codes 288
- Request Sense Error Codes 290
- Autochanger Error Codes 292
- Recovery 295
- Hardware Error Codes 306
- Autochanger Move Error Codes 316
- Diagnostic Tests 327
- Initialize Element 332
- Autochanger Error Codes 339
- Appendix BB-52 339
- Appendix C C-1 340
- Field Replaceable Units 342
- Appendix CC-6 345
- D Micro/Macro-Moves 346
- Micro/Macro-Moves 348
- Micro/Macro-Moves 369
- Appendix DD-24 369
- E Disconnect Timeout Settings 370
- Disconnect Timeout Settings 371
- Disconnect Timeouts 372
- Appendix EE-4 373
Verwandte Produkte und Handbücher für Interne Festplatten HP 220mx
Interne Festplatten HP J9F51A Datenblatt
(44 Seiten)
(44 Seiten)
Interne Festplatten HP QK555AT Datenblatt
(8 Seiten)
(8 Seiten)
Interne Festplatten HP C8R65A Datenblatt
(38 Seiten)
(38 Seiten)
Interne Festplatten HP BV848SB Datenblatt
(16 Seiten)
(16 Seiten)
Interne Festplatten HP FX505AV Datenblatt
(74 Seiten)
(74 Seiten)
Interne Festplatten HP FX490AV Datenblatt
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern