Hp ProLiant DL320e Gen8 Server Bedienungsanleitung Seite 38
- Seite / 96
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Hardware options installation 38
1.
Power down the server (on page 16).
2. Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3. Do one of the following:
o Extend the server from the rack (on page 16).
o Remove the server from the rack (on page 17).
4. Remove the access panel (on page 18).
5. Install the storage controller ("Expansion board options" on page 47).
6. Connect all necessary internal and external cabling to the storage controller. For more information on
these cabling requirements, see the document the ships with the option. For internal cable routing
information in different drive configuration, see "Storage cabling (on page 54)."
7. Install the access panel (on page 19).
8. Do one of the following:
o Slide the server into the rack.
o Install the server into the rack ("Installing the server into the rack" on page 27).
9. Install the drives ("Drive options" on page 31).
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
10. Connect each power cord to the server.
11. Connect each power cord to the power source.
12. Power up the server (on page 16).
For more information about the controller and its features, see the HP Smart Array Controllers for HP ProLiant
Servers User Guide on the HP website (http://www.hp.com/support/SAC_UG_ProLiantServers_en). To
configure arrays, see the Configuring Arrays on HP Smart Array Controllers Reference Guide on the HP
website (http://www.hp.com/support/CASAC_RG_en).
Upgrade options exist for the integrated array controller. For a list of supported options, see the QuickSpecs
on the HP website (http://www.hp.com/support).
Installing the FBWC module and capacitor pack
CAUTION: In systems that use external data storage, be sure that the server is the first unit to be
powered down and the last to be powered back up. Taking this precaution ensures that the system
does not erroneously mark the external drives as failed when the server is powered up.
To install the component:
1. Power down the server (on page 16).
2. Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3. Do one of the following:
o Extend the server from the rack (on page 16).
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Rear panel components 8
- System board components 9
- DIMM slot locations 10
- System maintenance switch 11
- NMI header 11
- Drive numbering 12
- • Eight-bay SFF drive model 13
- FBWC module LED definitions 14
- Fan locations 15
- Operations 16
- Remove the access panel 18
- Install the access panel 19
- Remove the air baffle 19
- Install the air baffle 20
- Remove the PCI riser cage 20
- Install the PCI riser cage 21
- Rack planning resources 23
- Optimum environment 23
- Temperature requirements 24
- Server warnings and cautions 25
- Rack warnings 26
- Installing hardware options 27
- Registering the server 30
- Introduction 31
- Security bezel option 31
- Drive options 31
- Installing a hot-plug drive 33
- Mini-SAS cable option 34
- Controller options 37
- Optical drive option 40
- Memory options 43
- HP SmartMemory 44
- DIMM identification 44
- Installing a DIMM 46
- Expansion board options 47
- 7. Reboot the server 53
- Cabling 54
- Optical drive cabling 58
- Power supply cabling 59
- Server mode 61
- HP product QuickSpecs 61
- HP iLO Management Engine 61
- Active Health System 62
- Intelligent Provisioning 63
- HP Insight Diagnostics 64
- Erase Utility 64
- HP Service Pack for ProLiant 65
- HP ROM-Based Setup Utility 66
- Auto-configuration process 67
- Boot options 67
- Utilities and features 68
- ROMPaq utility 69
- Automatic Server Recovery 69
- USB support 69
- Keeping the system current 70
- Version control 71
- ProLiant servers 71
- Troubleshooting 72
- System battery replacement 73
- Regulatory information 75
- Warranty information 76
- Electrostatic discharge 77
- Specifications 78
- Specification Value 79
- Support and other resources 81
- Customer Self Repair 83
- Reparo feito pelo cliente 85
- Acronyms and abbreviations 89
- Documentation feedback 93
- Index 94 94
- Index 95 95
- Index 96 96
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant DL320e Gen8 Server
(113 Seiten)
(115 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern