Hp ProLiant ML370 G5 Server Bedienungsanleitung Seite 43
- Seite / 135
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Hardware options installation 43
The Advanced Memory Protection option is configured in RBSU. By default, the server is set to Advanced
ECC mode. For more information, refer to HP ROM-Based Setup Utility (on page 82). If the configured
AMP mode is not supported by the installed FBDIMM configuration, the system boots in Advanced ECC
mode.
The following configuration requirements apply to all AMP modes:
• FBDIMMS must be ECC Registered DDR-2 SDRAM FBDIMMs.
• FBDIMMs must be installed in pairs.
• FBDIMM pairs in a memory bank must have identical HP part numbers.
• FBDIMMS must be populated as specified for each AMP memory mode.
• Memory Board 1 must always be populated with FBDIMMs installed in Bank A.
The memory subsystem for this server is divided into two memory controllers, one for each memory board.
This multiple memory board architecture provides enhanced memory performance in all AMP modes for
dual memory board configurations.
If the server contains more than 4 GB of memory, consult the operating system documentation about
accessing the full amount of installed memory.
Advanced ECC memory
Advanced ECC memory is the default memory protection mode for this server. In Advanced ECC, the
server is protected against correctable memory errors. The server provides notification if the level of
correctable errors exceeds a pre-defined threshold rate. The server does not fail because of correctable
memory errors. Advanced ECC provides additional protection over Standard ECC because it is possible
to correct certain memory errors that would otherwise be uncorrectable and result in a server failure.
Whereas standard ECC can correct single-bit memory errors, Advanced ECC can correct single-bit
memory errors and multi-bit memory errors if all failed bits are on the same DRAM device on the
FBDIMM.
In addition to general configuration requirements ("FBDIMM installation guidelines" on page 48),
Advanced ECC memory also has the following configuration requirements:
• For single-memory board configurations, FBDIMMs must be installed in sequential order, beginning
with memory board 1 - bank A.
• For dual-memory board configurations, FBDIMMs must be installed sequentially on each memory
board, beginning with memory board 1 - bank A, then memory board 2 - bank A.
• For dual memory board configurations, the same amount of total memory should be used on both
memory boards for maximum performance.
In Advanced ECC mode, FBDIMMs must be populated as specified in the following tables:
Single memory board configuration:
Memory board 1
configuration
Bank A
1A and 5A
Bank B
2B and 6B
Bank C
3C and 7C
Bank D
4D and 8D
1 X — — —
2 X X — —
3 X X X —
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Item Description Status 9
- Systems Insight Display LEDs 10
- Rear panel components 11
- Rear panel LEDs 12
- System board components 13
- System maintenance switch 14
- SAS and SATA device numbers 15
- SAS and SATA hard drive LEDs 16
- Online/activity 17
- LED (green) 17
- Fault/UID LED 17
- (amber/blue) 17
- Interpretation 17
- FBDIMM slots 18
- Power supply backplane LED 19
- Fan locations 19
- Operations 20
- Operations 21 21
- Operations 22 22
- Remove the rack bezel 23
- Operations 24 24
- Install the rack bezel 25
- Remove the access panel 25
- Install the access panel 26
- Remove the center wall 27
- Rack planning resources 28
- Optimum environment 29
- Temperature requirements 30
- Power requirements 30
- Rack warnings 31
- Server warnings and cautions 31
- Setup 32 32
- Installing hardware options 33
- Setting up a tower server 33
- Setup 34 34
- Registering the server 35
- Introduction 36
- Processor option 36
- 13. Install the heatsink 41
- 15. Install the PPM 41
- Memory options 42
- Advanced ECC memory 43
- Online spare memory 44
- Mirrored memory 45
- Memory boards and FBDIMMs 46
- Removing FBDIMMs 48
- Installing FBDIMMs 49
- Hot-plug hard drive options 50
- Remove the hard drive blank 51
- Prepare the hard drive 51
- Expansion board options 61
- Performance balancing 62
- Expansion slot cover 62
- Installing expansion boards 63
- Removing expansion boards 64
- • Rack rails 67
- • Cable management arm 67
- • Server rails 67
- • Rack bezel 67
- Remove the CD-ROM drive 69
- Install the center wall 74
- Cabling 75
- SAS cabling 76
- CD-ROM drive cabling 77
- Video cabling 78
- Parallel/serial port cabling 78
- Diskette drive cabling 79
- BBWC option cabling 79
- Internal USB connector 80
- Configuration and utilities 81
- HP ROM-Based Setup Utility 82
- Boot options 83
- BIOS Serial Console 83
- Configuring mirrored memory 83
- Array Configuration Utility 84
- Auto-configuration process 84
- Management tools 86
- Management Agents 88
- HP Systems Insight Manager 88
- Redundant ROM support 88
- USB support 89
- Diagnostic tools 90
- Integrated Management Log 91
- Keeping the system current 92
- Care Pack 93
- Battery replacement 94
- Battery replacement 95 95
- Troubleshooting 96
- Symbols on equipment 97
- Warnings and cautions 97
- Symptom information 98
- Loose connections 99
- Service notifications 100
- Troubleshooting flowcharts 100
- General diagnosis flowchart 101
- Symptoms: 103
- Troubleshooting 105 105
- POST problems flowchart 106
- OS boot problems flowchart 107
- • Redundancy failure 110
- Troubleshooting 111 111
- Electrostatic discharge 112
- FCC rating label 113
- Class A equipment 113
- Class B equipment 113
- Modifications 114
- • EMC Directive 2004/108/EC 115
- Japanese notice 116
- BSMI notice 116
- Korean notice 117
- Laser compliance 117
- Battery replacement notice 117
- Specifications 119
- Specification Value 120
- Technical support 121
- Customer Self Repair 122
- Technical support 124 124
- Reparo feito pelo cliente 126
- Technical support 127 127
- Technical support 128 128
- Acronyms and abbreviations 129
- Index 132 132
- Index 133 133
- Index 134 134
- Index 135 135
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant ML370 G5 Server
(78 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.962 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern