Hp ProCurve 520wl Wireless Access Point Bedienungsanleitung Seite 106
- Seite / 142
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Parameter Tables
6-23
parameter tables
parameter tablesparameter tables
parameter tables
Objects contain groups that contain both parameters and parameter tables.
Use the following Tables to configure the Access Point. Columns used on the tables include:
— Name - Parameter, Group, or Table Name
— Type - Data type
— Values - Value range, and default value, if any
— Access = access type, R = Read Only (show), RW = Read-Write (can be “set”), W = Write Only
— CLI Parameter - Parameter name as used in the Access Point
Access Point network objects are associated with Groups. The network objects are listed below and associated parameters are
described in the following Parameter Tables:
Q System Parameters - Access Point system information
Q Inventory Management Information - Hardware, firmware, and software version information
Q Network Parameters - IP and Ethernet information
Q DHCP Server Parameters - Enable or disable dynamic host configuration
Q VLAN Parameters - Enable, disable, and configure VLAN (Virtual LAN) settings
Q Ethernet Interface Parameters - Set the speed and duplex of the Ethernet port
Q Wireless Interface Parameters - Wireless card Information
Q Wireless Distribution System (WDS) Parameters - Configure the WDS partnerships
Q Security Parameters - Access Point security settings
Q Wireless Interface Security Parameters - Configure WEP encryption settings
Q Primary and Backup RADIUS Server Table Parameters - RADIUS Authentication and Accounting information
Q MAC Access Control Parameter - Control wireless access based on MAC address
Q Management Parameters - Control access to the WL520’s management interfaces
Q SNMP Parameters - Set read and read/write passwords
Q IP Access Table Parameters - Configure range of IP addresses that can access the WL520
Q SNMP Table Host Table Parameters - Enter the list of IP addresses that will receive alarms from the WL520
Q Telnet Parameters - Telnet Port setup
Q Serial Port Parameters - Serial Port setup
Q TFTP Server Parameters - Set up for file transfers; specify IP Address, file name, and file type
Q HTTP (web browser) Parameters - Set up the graphical web browser interface
Q Advanced Parameters
Q Link Integrity Group - Monitor link status
Q Proxy ARP Parameters - Enable or disable proxy ARP for wireless clients
Q Ethernet Protocol Filtering Parameters - Control network traffic based on protocol type
Q Broadcast Filtering Table - Enable or disable proxy ARP for wireless clients
Q IP ARP Filtering Parameters - Control which ARP messages are sent to wireless clients based on IP settings
Q TCP/UDP Port Filtering - Filter IP packets based on TCP/UDP port
Q Syslog Parameters - Configure the WL520 to send Syslog information to network servers
Q IAPP Parameters - Enable or disable the Inter-Access Point Protocol
Q SpectraLink VoIP Parameters - Enable or disable SpectraLink Voice over IP feature
Q Bridging Parameters
Q Static MAC Address Filter Table - Enable and disable specific addresses
Q Spanning Tree Parameters - Used to help prevent network loops
Q Storm Threshold Parameters - Set threshold for number of broadcast packets
Q Intra BSS Subscriber Blocking - Enable or disable peer to peer traffic on the same AP
Q Packet Forwarding Parameters - Redirect traffic from wireless clients to a specified MAC address
Q CLI Monitoring Parameters - View WL520’s statistics
- Contents 1
- 5 troubleshootingtr ub h 4
- Dynamic Frequency Selection 11
- Download the Latest Software 22
- CAUTION: 23
- Ethernet Settings 32
- If You Encounter Problems 38
- Q Management Interface 39
- Q Issuing System Commands 39
- Management Interface 40
- Monitoring Network Statistics 41
- Issuing System Commands 47
- Network Settings 52
- VLAN Support 53
- Management Settings 58
- Setting Filters 60
- Alarms (SNMP Traps) 63
- Bridge Configuration Settings 65
- Advanced RADIUS Features 72
- Troubleshooting Concepts 76
- Symptoms and Solutions 77
- Recovery Procedures 79
- System Alarms (Traps) 82
- Related Applications 83
- ? (list commands) 87
- CLI Command Types 89
- Q Creation 94
- Q Modification 94
- Q Enabling/Disabling 94
- Q Deletion 94
- Other Network Settings 100
- Parameter Tables 106
- Configuration Settings 124
- Q Hardware Specifications 139
- Q Radio Specifications 139
- Hardware Specifications 140
- Radio Specifications 141
Verwandte Produkte und Handbücher für Router Hp ProCurve 520wl Wireless Access Point
(191 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.294 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern