Hp ProLiant SL2500 Scalable System Bedienungsanleitung Seite 91
- Seite / 117
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
CLI commands 91
Set SNMP contact
• Command:
SET SNMP CONTACT "<sysContact>"
• Description:
Sets the MIB II sysContact field.
Set SNMP location
• Command:
SET SNMP LOCATION "<sysLocation>"
• Description:
Sets the MIB II sysLocation field.
Set SNMP trapdest
• Command:
SET SNMP TRAPDEST <<ip_addresses>|NONE>
• Description:
o Sets the IP addresses where SNMP traps are sent.
You can set up to four SNMP trap destinations. For example, enter:
SET SNMP TRAPDEST x.x.x.x y.y.y.y z.z.z.z a.a.a.a
If you specify NONE, then no trap destinations are set. For example, enter:
SET SNMP TRAPDEST NONE
o HP APM supports the following SNMP traps:
NOTE: SNMP traps denoted by an * are not supported on the HP ProLiant s6500 Chassis.
— cpqRackNameChanged
— cpqRackEnclosureRemoved
— cpqRackEnclosureInserted
— cpqRackEnclosureFanRemoved *
— cpqRackEnclosureFanInserted *
— cpqRackEnclosureFanFailed
— cpqRackEnclosureFanOK
— cpqRackPowerSupplyFailed
— cpqRackPowerSupplyOK
— cpqRackPowerSupplyRemoved
— cpqRackPowerSupplyInserted
— cpqRackServerBladeRemoved
- HP Advanced Power Manager 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Contents 7 7
- Introduction 8
- HP APM kit contents 9
- HP APM front view 10
- HP APM rear view 11
- HP APM connections 11
- Item Component Connects To 12
- Required connections 13
- Identifying the RDM1 ports 13
- • HP Moonshot System 14
- Using RJ-45 connections 16
- Rack chassis numbering 17
- Automatic discovery 18
- Introduction 19 19
- Preparing for installation 20
- Configuring the HP APM 20
- Serial port configuration 22
- Network configuration 22
- Security configuration 23
- Protocol configuration 23
- Command Line Interface 24
- Saving configurations 25
- Topology and inventory 25
- Command Line Interface 26 26
- Command Line Interface 27 27
- Showing the servers 28
- Showing topology 28
- Showing assetinfo 29
- Showing the MAC address 30
- Command Line Interface 31 31
- Logging 32
- Logging 33 33
- Logging 34 34
- External logging 35
- HP APM fault messages 35
- XML-related fault messages 37
- Working with RADIUS servers 37
- Showing a RADIUS server 38
- Power capping 39
- Power capping licensing 40
- Rack level power capping 40
- Power baseline 41
- Power capping 42 42
- Setting power capping 43
- Power capping 44 44
- Power capping 45 45
- Power capping 46 46
- Power capping with zones 48
- Power commands 49
- Setting power 51
- Power capping 52 52
- Power capping 53 53
- General commands 54
- Working with accounts 55
- Working with zones 56
- General commands 57 57
- Using password recovery 58
- Showing configurations 59
- Using the help 59
- Setting the name 59
- Setting the time 60
- Setting the session timeout 60
- Setting the UID LED 60
- Showing information 60
- Showing the name 61
- Showing the time 61
- Showing the version 61
- General commands 62 62
- Connecting and setting ports 63
- Using SNMP 64
- Setting the SNMP contact 65
- Setting the SNMP location 65
- Using SNMP 66 66
- Using XML 67
- Response definitions 68
- Enabling XML 69
- Showing and resetting keys 69
- Logging in through XML 69
- Modifying the user account 69
- Modifying compute node power 70
- Resetting HP APM 71
- Using XML 72 72
- Firmware 73
- Troubleshooting 74
- CLI commands 75
- CLI commands 76 76
- Disable password 77
- Enable password 77
- Set password account 77
- • Description: 78
- • Command: 78
- CLI commands 79 79
- Reboot CM 80
- Reset factory 80
- Save config 80
- Set gateway 81
- Set name 81
- Set power 81
- Set serial 82
- Set syslog 82
- Set time 82
- Set timeout 82
- Set power baseline 83
- Set power cap 83
- Set asset info 83
- CLI commands 84 84
- Show name 85
- Show power 85
- Show rack 85
- Show servers 86
- Show topology 86
- Show asset info 86
- Show MAC address 87
- Show time 87
- Show power baseline 87
- Show version 87
- Upgrade image 87
- Add zone 88
- Save zones 89
- Show zones 89
- Remove zone 89
- Enable pollpower 89
- Disable pollpower 89
- Enable SNMP 90
- Disable SNMP 90
- Show SNMP 90
- Set SNMP RO 90
- Set SNMP RW 90
- Set SNMP contact 91
- Set SNMP location 91
- Set SNMP trapdest 91
- Enable XML 92
- Enable XML secure 92
- Disable XML 92
- Show keys 92
- Reset keys 92
- CLI commands 93 93
- Set RADIUS pollsec 94
- Enable NTP 94
- Set NTP server 94
- Set NTP poll 94
- Show NTP server 94
- Show NTP poll 95
- Disable NTP 95
- Connect port 95
- Set port 95
- XML commands 96
- Get rack topology 97
- Get rack information 97
- Modify compute node power 97
- Get compute node 98
- Get all compute node power 99
- Reset HP APM 99
- Supported MIB objects 100
- PDU identity table 109
- PDU input table 109
- Regulatory information 110
- Warranty information 111
- Support and other resources 112
- Acronyms and abbreviations 113
- Documentation feedback 114
- Index 115 115
- Index 116 116
- Index 117 117
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant SL2500 Scalable System
(172 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.511 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern