Hp ProLiant SL2500 Scalable System Bedienungsanleitung Seite 37
- Seite / 117
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Logging 37
XML-related fault messages
The following XML-related fault messages might appear in your fault log:
• Failed to allocate memory for XML parser.
• Failed to create a XML Output File for writing.
• Failed to create a XML Output.
• XML Rear Error
To attempt to resolve these error messages, first "Disable XML," and then "Enable XML" or "Enable XML
Secure."
Working with RADIUS servers
The HP APM firmware supports the RADIUS authentication protocol. When RADIUS is enabled, it is used to
verify login requests to HP APM through SSH, telnet, or the serial console.
Adding and removing a RADIUS server
To add a RADIUS server, enter ADD RADIUS SERVER <ip_address> <shared_secret>.
This command specifies an initial or additional RADIUS server to the HP APM list of authentication servers.
The authentication proceeds in the same order that these servers were added to the configuration. Up to a
total of five RADIUS servers can be added for authentication purposes. Port 1812 is assumed. The IP address
must match the location of the RADIUS server. The shared secret must be specified in quotes and must match
the string that has been programmed into the RADIUS server when receiving authentication requests from HP
APM.
To set the number of times HP APM polls each of the RADIUS server indicated in the ADD RADIUS SERVER
command, enter SET RADIUS POLLNUM. To set the number of seconds HP APM waits for a reply from the
RADIUS server, enter SET RADIUS POLLSEC. These settings can only be set globally and cannot be applied
to each individual RADIUS server.
To remove a RADIUS server, enter REMOVE RADIUS SERVER <index>.
This command removes a previously added RADIUS server that matches the index indicated with the SHOW
RADIUS command. RADIUS authentication is no longer attempted against this server.
Enabling and disabling a RADIUS server
To enable HP APM as a RADIUS client, enter ENABLE RADIUS.
All login attempts through SSH, Telnet, and the serial console are authenticated through the list of RADIUS
servers that were indicated with the ADD RADIUS SERVER command. Authentication is also verified against
the local password if the RADIUS servers indicate no access.
To disable RADIUS authentication on HP APM, enter DISABLE RADIUS.
Authentication through RADIUS no longer takes place, but password checking is still done against the local
password if that is still enabled. This command does not clear out the configured RADIUS servers.
- HP Advanced Power Manager 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Contents 7 7
- Introduction 8
- HP APM kit contents 9
- HP APM front view 10
- HP APM rear view 11
- HP APM connections 11
- Item Component Connects To 12
- Required connections 13
- Identifying the RDM1 ports 13
- • HP Moonshot System 14
- Using RJ-45 connections 16
- Rack chassis numbering 17
- Automatic discovery 18
- Introduction 19 19
- Preparing for installation 20
- Configuring the HP APM 20
- Serial port configuration 22
- Network configuration 22
- Security configuration 23
- Protocol configuration 23
- Command Line Interface 24
- Saving configurations 25
- Topology and inventory 25
- Command Line Interface 26 26
- Command Line Interface 27 27
- Showing the servers 28
- Showing topology 28
- Showing assetinfo 29
- Showing the MAC address 30
- Command Line Interface 31 31
- Logging 32
- Logging 33 33
- Logging 34 34
- External logging 35
- HP APM fault messages 35
- XML-related fault messages 37
- Working with RADIUS servers 37
- Showing a RADIUS server 38
- Power capping 39
- Power capping licensing 40
- Rack level power capping 40
- Power baseline 41
- Power capping 42 42
- Setting power capping 43
- Power capping 44 44
- Power capping 45 45
- Power capping 46 46
- Power capping with zones 48
- Power commands 49
- Setting power 51
- Power capping 52 52
- Power capping 53 53
- General commands 54
- Working with accounts 55
- Working with zones 56
- General commands 57 57
- Using password recovery 58
- Showing configurations 59
- Using the help 59
- Setting the name 59
- Setting the time 60
- Setting the session timeout 60
- Setting the UID LED 60
- Showing information 60
- Showing the name 61
- Showing the time 61
- Showing the version 61
- General commands 62 62
- Connecting and setting ports 63
- Using SNMP 64
- Setting the SNMP contact 65
- Setting the SNMP location 65
- Using SNMP 66 66
- Using XML 67
- Response definitions 68
- Enabling XML 69
- Showing and resetting keys 69
- Logging in through XML 69
- Modifying the user account 69
- Modifying compute node power 70
- Resetting HP APM 71
- Using XML 72 72
- Firmware 73
- Troubleshooting 74
- CLI commands 75
- CLI commands 76 76
- Disable password 77
- Enable password 77
- Set password account 77
- • Description: 78
- • Command: 78
- CLI commands 79 79
- Reboot CM 80
- Reset factory 80
- Save config 80
- Set gateway 81
- Set name 81
- Set power 81
- Set serial 82
- Set syslog 82
- Set time 82
- Set timeout 82
- Set power baseline 83
- Set power cap 83
- Set asset info 83
- CLI commands 84 84
- Show name 85
- Show power 85
- Show rack 85
- Show servers 86
- Show topology 86
- Show asset info 86
- Show MAC address 87
- Show time 87
- Show power baseline 87
- Show version 87
- Upgrade image 87
- Add zone 88
- Save zones 89
- Show zones 89
- Remove zone 89
- Enable pollpower 89
- Disable pollpower 89
- Enable SNMP 90
- Disable SNMP 90
- Show SNMP 90
- Set SNMP RO 90
- Set SNMP RW 90
- Set SNMP contact 91
- Set SNMP location 91
- Set SNMP trapdest 91
- Enable XML 92
- Enable XML secure 92
- Disable XML 92
- Show keys 92
- Reset keys 92
- CLI commands 93 93
- Set RADIUS pollsec 94
- Enable NTP 94
- Set NTP server 94
- Set NTP poll 94
- Show NTP server 94
- Show NTP poll 95
- Disable NTP 95
- Connect port 95
- Set port 95
- XML commands 96
- Get rack topology 97
- Get rack information 97
- Modify compute node power 97
- Get compute node 98
- Get all compute node power 99
- Reset HP APM 99
- Supported MIB objects 100
- PDU identity table 109
- PDU input table 109
- Regulatory information 110
- Warranty information 111
- Support and other resources 112
- Acronyms and abbreviations 113
- Documentation feedback 114
- Index 115 115
- Index 116 116
- Index 117 117
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant SL2500 Scalable System
(172 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.709 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern