Hp StorageWorks Scalable File Share Bedienungsanleitung Seite 192
- Seite / 362
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Changing the system parameters7–10
• If both the administration and the MDS servers are affected, enter the configure server
command for each server, as shown in the following example, where south1 is the administration
server, and south2 is the MDS server:
sfs> configure server south1
sfs> configure server south2
• If all servers are affected, enter the configure server command for the servers in the order
shown in the following example, where south1 is the administration server, south2 is the MDS
server, and south3 and south4 are the Object Storage Servers:
sfs> configure server south1
sfs> configure server south2
sfs> configure server south[3-4]
7.4 Adding, changing, or removing the Alias IP on a Gigabit Ethernet
network
In most HP SFS systems, an alias IP address is only configured on one network, but it is possible to configure
an alias on each Gigabit Ethernet network.
The alias IP address is an alias to the first server in the HP SFS system, but will route to the second server if
the first server is unavailable. Client nodes may use the alias IP address to retrieve file systems configuration
data from the LDAP database when they are mounting file systems.
To add, change, or remove an alias IP on a Gigabit Ethernet network, perform the following steps:
1. Log in to the administration server.
2. Run the configure system command as described in Section 7.2 and add, change or remove the
alias IP address on the network as required.
3. Reconfigure all servers, as shown in the following example:
sfs> configure server south[1-4]
4. Verify that the alias IP address has been updated, as shown in the following example. In this example,
eth1 is the interface on the network where the alias IP address was updated:
# ifconfig
.
.
.
eth1:0 Link encap:Ethernet HWaddr 00:0B:CD:DB:C3:BC
inet addr:16.123.123.110 Bcast:16.123.123.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:15
You do not need to unmount file systems for the change to take effect. Client nodes currently connected to
the file systems are unaffected. However, any client nodes that are mounting file systems after the change
has been made cannot use the old alias IP address to access the file system configuration data.
7.5 Changing the IP address of an individual server
You can change the IP address on a Gigabit Ethernet or InfiniBand network for an individual server as
follows:
1. Enter the show network command to determine which networks are on the system, as shown in the
following example. In this example, the nic2 network is the Gigabit Ethernet Interconnect:
sfs> show network
Name Device Role
---- ------ ----
elan0 n/a interconnect
mp0 n/a console
nic1 eth0 management
nic2 eth1 interconnect
- System User Guide 1
- Version 2.2 1
- Contents 3
- 4 Viewing system information 4
- A CLI commands 9
- About this guide 11
- HP SFS documentation 12
- Documentation conventions 12
- Naming conventions 13
- For more information 13
- Providing feedback 13
- Safety considerations 15
- 1Overview 17
- 1.1 Product overview 18
- 1.1.2 Overview of HP SFS 19
- 1.1.3 HP SFS configurations 20
- 1.1.3.2 Storage 21
- 1.1.3.3 Network connections 23
- 1.1.3.3.2 Management network 24
- 1.3 Supported hardware 25
- Overview1–10 26
- 2 The sfsmgr utility 27
- 2.1 Overview 28
- 2.2 Starting the SFS CLI 28
- 2.3 Running sfsmgr commands 29
- The sfsmgr utility2–6 32
- 3 Operating the system 33
- 3.1 Booting the system 34
- 3.2 Shutting down the system 36
- 3.3 Booting a server 36
- 3.4 Booting multiple servers 37
- 3.7 Stopping a file system 39
- 3.8 Starting a file system 40
- 3.11 Managing licenses 47
- 3.12 Managing remote access 53
- 3.12.3 Viewing authorizations 55
- 4Viewing system information 57
- 4.4 Viewing LUN information 67
- 4.5 Viewing array information 69
- 4.6 Viewing event logs 72
- 4.6.1.1 Event filters 73
- 4.6.1.2 Event severity 73
- 4.6.1.3 Event facility 73
- LUNs — EVA4000 storage 88
- File system name 100
- Mount point 100
- Stripe size 100
- MDS LUNs 100
- Number of OST services 101
- Interconnects 102
- Quota options 102
- Mount options 102
- Stripe count 102
- 5.4 Operating a file system 111
- 5.7 Managing quotas 121
- command on 123
- # lfs quotacheck -ug /data 124
- 5.7.3 Checking quota limits 125
- 5.10 Deleting file systems 127
- 6.1 Verifying the system 132
- Verifying the system 6–5 135
- # ssh south3-adm hostname 150
- Sequential test 151
- Parallel test 152
- Incremental test 152
- Latency test 157
- Unidirectional bandwidth test 158
- Verifying the system 6–33 163
- 6.2 Managing email alerts 169
- 6.2.4 Default email alerts 171
- Managing email alerts 6–43 173
- 6.2.5 Modifying email alerts 174
- 6.2.6 Creating email alerts 174
- 6.2.7 Viewing email alerts 175
- 6.2.9 Deleting email alerts 176
- 6.5 Removing log files 180
- 6.6.1 Overview 181
- 6.6.2 Viewing the IML 181
- 6.6.3 Clearing the IML 181
- Configuration impact 201
- Object Storage Server 202
- Number FCA2214 DC) 204
- [root@south4 var]# raw -qa 206
- 8.2 Upgrading firmware 214
- # service cluster stop 216
- 8.3.3 Adding SFS20 arrays 222
- 8.3.4 Removing SFS20 arrays 222
- 9Troubleshooting 225
- 9.2 Server fails to boot 227
- 9.3 Server stops responding 227
- /proc/fs/lustre/mds/mds2 247
- # repair-lfsck -f scratch 250
- Troubleshooting9–34 258
- Remedial action 261
- 9.27.2.1 Recreating files 262
- 9.30 Accessing consoles 275
- 9.31.1.2 Using a Web browser 276
- 9.32 Troubleshooting licenses 277
- 9.36 System log files 288
- ACLI commands 295
- A.1 General information 296
- A.2 accept license command 297
- A.3 activate ost command 297
- A.4 boot server command 297
- A.5 configure commands 298
- A.5.2 configure server 300
- A.6 create commands 301
- A.6.3 create authorization 302
- A.6.4 create database_backup 302
- A.6.5 create filesystem 303
- A.7 deactivate ost command 304
- A.8 delete commands 304
- A.8.2 delete array 305
- A.8.3 delete attribute 305
- A.8.4 delete authorization 305
- A.9 disable commands 306
- A.9.2 disable server 307
- A.10 enable commands 308
- A.11 help command 309
- A.12 kill command command 309
- A.13 modify commands 310
- Interactive mode 311
- Scripted mode 311
- A.14 monitor command command 312
- A.15 pause filesystem command 312
- A.16 quit command 313
- A.18 scan mac command 313
- A.19 set commands 314
- A.19.2 set attribute 315
- A.19.3 set lun 316
- A.19.4 set nics 317
- A.19.5 set password 318
- A.19.6 set server 318
- A.20 show commands 319
- A.20.4 show authorization 320
- A.20.5 show commands 320
- A.20.6 show database_backups 321
- A.20.7 show filesystem 321
- A.20.8 show license 321
- A.20.9 show log 321
- Examples 322
- A.20.10 show lun 323
- A.20.11 show network 323
- A.20.12 show ost 323
- A.20.13 show server 324
- A.20.14 show support 324
- A.20.15 show system 324
- A.20.16 show version 324
- A.21 shutdown server command 325
- A.22 start filesystem command 325
- A.23 stop filesystem command 326
- A.24 syscheck command 326
- A.26 ! command 328
- B Performance figures 329
- B.1 I/O performance 330
- SFS20 storage — 250GB disks 331
- SFS20 storage — 5000GB disks 331
- B.2 Network performance 332
- B.3 SFS20 array configuration 333
- RAID5 and ADG Read Bandwidth 334
- 64 clients 336
- 128 Clients 336
- 192 clients 336
- Bandwidth vs Clients 337
- Single Client Varying OSTs 338
- 1500 MTU Average Write MB/sec 339
- 9000 MTU Average Read MB/sec 340
- C.1 EVA4000 storage examples 344
- EVA4000 storage examples C–3 345
- C.2 SFS20 storage examples 346
- SFS20 storage examples C–5 347
- D.1 RAID rebuild information 350
- E HP SFS specifications 351
- HP SFS specificationsE–4 354
- Glossary 355
- Glossary–2 356
- Glossary–3 357
- Glossary–4 358
- 9-24, 9-25 361
Verwandte Produkte und Handbücher für Lager Hp StorageWorks Scalable File Share
Lager Hp SAN Bedienungsanleitung
(30 Seiten)
(30 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern