Hp 3PAR Remote Copy Software Bedienungsanleitung Seite 230
- Seite / 344
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
C.12
Bidirectional Synchronous Disaster Recovery Example
Remote Copy User’s Guide InForm OS Version 2.3.1
5 On the restored system (InServ1), issue the showrcopy command and verify that the
target displays ready, the sending links display Up, the volumes are Syncing, and the
group is displayed as -Rev as shown in bold in the following example:
After the synchronization is verified, restore the direction of each system.
On InServ1:
# showrcopy
Remote Copy System Information
Status: Started, Normal
Target Information
Name ID Type Status Options Policy
InServ2 9 IP ready mirror_config
Link Information
Target Node Address Status Options
InServ2 0 10.100.33.11 Up
InServ2 1 10.101.33.11 Up
receive 0 10.100.33.11 Up
receive 1 10.101.33.11 Up
Group Information
Name Target Status Role Mode Options
sync_group_1 InServ2 Started Secondary-Rev Sync
LocalVV ID RemoteVV ID SyncStatus LastSyncTime
localvv.0 413 remotevv.0 375 Syncing Thu Dec 14 17:58:25 PST 2006
localvv.1 414 remotevv.1 376 Syncing Thu Dec 14 17:58:25 PST 2006
Name Target Status Role Mode Options
sync_group_2.r11 InServ2 Stopped Secondary Sync
LocalVV ID RemoteVV ID SyncStatus LastSyncTime
remotevv.0 423 localvv.0 385 Stopped Thu Dec 14 17:51:49 PST 2006
remotevv.1 424 localvv.1 386 Stopped Thu Dec 14 17:51:44 PST 2006
CAUTION: The group must be started at the time the setrcopygroup restore
command is issued. Issue the showrcopy groups <groupname> command to
confirm the group has been started. If it has not been started then issue the
startrcopygroup <groupname> command and wait for any synchronizations
that are started to complete before issuing the setrcopygroup restore
command.
- 3PAR Remote Copy 1
- User’s Guide 1
- 3 Remote Copy Setup 5
- 4 Using Remote Copy 6
- AQuick Setup Guide 7
- B Remote Copy Commands 7
- D Comparing MTU Speeds 9
- RH Revision History 9
- Table of Contents 10
- Introduction 11
- 1.1 Audience 12
- 1.2 Related Documentation 12
- 1.3 Organization 13
- 1.4 Typographical Conventions 14
- 1.5 Advisories 15
- Advisories 16
- Remote Copy Overview 17
- 2.1 Overview 19
- 2.2.2 Remote Copy Concepts 20
- 2.4 Remote Copy Pairs 22
- 2.5 Remote Copy Configuration 23
- Remote Copy Configuration 24
- 2.5.3 N-to-1 Configurations 25
- 2.5.4 1-to-N Configurations 27
- 2.6 Remote Copy Targets 31
- Direction of data 32
- 2.7 Remote Copy Links 33
- 2.8 Remote Copy Connections 34
- 2.8.1 IP Networks 35
- 2.9 Remote Copy Operation 36
- 2.9.1 Volume Group Modes 38
- 2.9.1.1 Synchronous Mode 39
- 2.9.1.1.1 Latency 40
- 2.9.2 Synchronization Types 41
- Remote Copy Operation 42
- 2.9.7 Role Reversal 46
- 2.11.1 In Synchronous Mode 47
- Use of Virtual Copy Snapshots 48
- 2.13 Error Handling 51
- 2.13.2 Double Link Failure 52
- Error Handling 53
- 2.13.5 Write Errors 54
- 2.13.6 Read Errors 55
- TCP/IP Network 57
- Requirements and Restrictions 58
- N-to-1 Restrictions 59
- 2.14.2 1-to-N Restrictions 60
- Remote Copy Setup 63
- 3.1 Available Setup Methods 64
- 3.2 Preparing for Setup 64
- 3.4.2.1 Setting the Gateway 71
- <N:S:P>) 72
- 3.5 Setting Up Remote Copy 78
- 3.5.1.4 Start Copying 85
- Node 0 WWN: 20210002AC0000C3 92
- Node 1 WWN: 21210002AC0000C3 92
- <group_name> 100
- Using Remote Copy 107
- 4.1 Management 108
- 4.5 Manual Resynchronization 111
- Modifying Virtual Volumes 115
- 4.9 Limiting Throughput 116
- 4.10 Stopping Remote Copy 117
- 4.11 Remote Copy Commands 117
- Remote Copy Commands 118
- Remote Copy volume group 120
- Task Command 120
- Performance and Scripting 121
- Considerations 121
- 5.1.2 Initial Synchronization 122
- 5.1.3 Distance 122
- 5.1.4 MTU Size 122
- 5.1.5 Autonegotiation 123
- 5.1.6 Remote Copy Mode 123
- 5.1.6.2 Synchronous Mode 124
- 5.3 Scripting Notes 125
- Scripting Notes 126
- Quick Setup Guide 127
- Table A-1. RCIP Setup 128
- A.3 Setting Up Remote Copy 129
- Table A-3. Remote Copy Setup 130
- Setting Up Remote Copy 131
- InForm OS CLI 135
- Administrator’s 135
- RESTRICTIONS 142
- EXAMPLES 142
- Group1 142
- specifier 173
- ■ Port. The port ID 208
- Group1 should be 218
- Example Setup and 219
- Disaster Recovery 219
- Chapter 3, Remote Copy Setup 220
- Remote Copy Setup Examples 221
- On InServ1: 224
- # showrcopy 224
- On InServ2: 225
- On InServ2 229
- InServ2 (Primary) 233
- InServ3 (Primary) 233
- InServ1 (Secondary) 233
- Direction of data replication 233
- InServ2 (Backup) 245
- InServ3 (Backup) 245
- InServ1 (Primary) 245
- ■ On InServA: 258
- ■ On InServB: 259
- ■ On InServC: 260
- InServB 267
- In the example above: 267
- ◆ On InServA: 269
- ◆ On InServB: 270
- ◆ On InServC: 271
- command on InServB and 281
- Primary-Rev) 284
- InServC 287
- -discard option bypasses 299
- To begin data migration: 317
- startrcopygroup -t 321
- Primary-Rev 326
- Primary, rather 329
- Comparing MTU Speeds 331
- Revision History 343
Verwandte Produkte und Handbücher für Lager Hp 3PAR Remote Copy Software
Lager Hp X500 Data Vault Bedienungsanleitung
(331 Seiten)
(331 Seiten)
Lager Hp XP7 Storage Bedienungsanleitung
(208 Seiten)
(208 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern