Hp ProLiant ML350 G4 Server Bedienungsanleitung Seite 113
- Seite / 156
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Troubleshooting 113
Observe local occupation health and safety requirements and
guidelines for manual handling.
•
•
•
•
Obtain adequate assistance to lift and stabilize the chassis
during installation or removal.
The server is unstable when not fastened to the rails.
When mounting the server in a rack, remove the power
supplies and any other removable module to reduce the overall
weight of the product.
CAUTION: To properly ventilate the system, you must provide
at least 7.6 cm (3.0 in) of clearance at the front and back of the server.
CAUTION: The server is designed to be electrically grounded
(earthed). To ensure proper operation, plug the AC power cord into a
properly grounded AC outlet only.
Preparing the Server for Diagnosis
1. Be sure the server is in the proper operating environment with adequate
power, air conditioning, and humidity control. Refer to the server
documentation ("Environmental Specifications" on page 145
) for required
environmental conditions.
2. Record any error messages displayed by the system.
3. Remove all diskettes and CDs from the media drives.
4. Power down the server and peripheral devices if you will be diagnosing the
server offline. Always perform an orderly shutdown, if possible. This means
you must:
a. Exit any applications.
b. Exit the operating system.
c. Power down the server ("Powering Down the Server" on page 25
).
- User Guide 1
- Audience Assumptions 2
- Contents 3
- Index 153 7
- Front Panel Components 9
- Front Panel LEDs and Buttons 10
- Rear Panel Components 12
- Rear Panel LEDs 13
- System Board Components 14
- NMI Jumper 16
- System Maintenance Switch 16
- System Board LEDs 17
- Hot-Plug Hard Drive IDs 20
- Item Description 21
- SATA or SAS Hard Drive LEDs 24
- Server Operations 25
- Removing Access Panel 27
- Server Setup 29
- Optimum Environment 30
- Server Setup 31 31
- Temperature Requirements 32
- Power Requirements 32
- Rack Planning Resources 33
- Rack Warnings 34
- Server Setup 35 35
- Installing Hardware Options 36
- Setting up a Tower Server 37
- Server Setup 39 39
- Torx screwdriver 41
- Server Setup 43 43
- Registering the Server 44
- Introduction 45
- Processor Option 46
- 7. Install the heatsink 48
- Memory Options 50
- Single- and Dual-Rank DIMMs 51
- DIMM Installation Guidelines 52
- Installing DIMMs 52
- Hard Drive Options 54
- SCSI Hard Drive Guidelines 55
- Identifying Guide Screws 58
- Removing Shipping Brackets 59
- Expansion Board Options 67
- Installing the Rack Server 76
- Installing a Redundant Fan 78
- Server Cabling 79
- Identifying SCSI Components 80
- Media Bays and Hard Drives 81
- Server Cabling 83 83
- Duplex Hot-Plug SCSI Cabling 84
- Server Cabling 85 85
- Internal SCSI Components 86
- Server Cabling 87 87
- SATA or SAS Cabling 89
- 1 SATA 1 connector 90
- 2 SATA 2 connector 90
- Server Cabling 91 91
- IDE Controller 92
- Configuration Tools 93
- ROM-Based Setup Utility 95
- BIOS Serial Console 97
- Array Configuration Utility 97
- Management Tools 99
- Automatic Server Recovery 100
- ROMPaq Utility 100
- Erase Utility 102
- Management Agents 103
- HP Systems Insight Manager 103
- Redundant ROM Support 103
- Diagnostic Tools 105
- Array Diagnostic Utility 106
- HP Insight Diagnostics 106
- Integrated Management Log 106
- Keeping the System Current 107
- ProLiant Support Packs 108
- Care Pack 108
- Troubleshooting 109
- Symbols on Equipment 110
- Warnings and Cautions 111
- Troubleshooting 113 113
- Symptom Information 114
- Diagnostic Steps 115
- General Diagnosis Flowchart 117
- Power-On Problems Flowchart 119
- Troubleshooting 121 121
- POST Problems Flowchart 122
- Troubleshooting 123 123
- OS Boot Problems Flowchart 125
- Troubleshooting 127 127
- Troubleshooting 129 129
- Battery Replacement 131
- 5. Remove the battery 132
- FCC Rating Label 134
- Class A Equipment 134
- Class B Equipment 135
- Modifications 136
- Mouse Compliance Statement 136
- Japanese Notice 138
- BSMI Notice 138
- Korean Notices 139
- Laser Compliance 139
- Battery Replacement Notice 140
- Electrostatic Discharge 143
- Discharge 144
- Server Specifications 145
- Specification 146
- Technical Support 147
- Customer Self Repair 148
- Acronyms and Abbreviations 149
Verwandte Produkte und Handbücher für Computerhardware Hp ProLiant ML350 G4 Server
(103 Seiten)Western Reserve Controls 1782-JDC manuály
Uživatelské manuály a uživatelské příručky pro Brány / ovladače Western Reserve Controls 1782-JDC.
Poskytujeme 3 manuály pdf Western Reserve Controls 1782-JDC ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern