Hp MPX200 Multifunction Router Bedienungsanleitung Seite 232
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Table 34 MPX200 log messages (continued)
The FCIP route #n went down because
the Fibre Channel port on the remote
peer went down.
ErrorFCIPFcipRoute#%d: FC link on the
remote peer went down
172322
TCP link for FCIP route #n has been
established.
InfoFCIPFcipRoute#%d: TCP Link Up184515
FCIP link is up for FCIP route #n.InfoFCIPFcipRoute#%d: FCIP Link Up184536
FCIP route #n: Incorrect VLAN
configuration.
ErrorFCIPFcipRoute#%d: VLAN Info
Unavailable
184542
Ethernet port was not able to negotiate
the configured speed.
ErrorNICQL3xxx:%s: Auto Negotiation
error detected
205571
Ethernet port speed is not supported.ErrorNICQL3xxx:eth%d: Unsupported speed
portConfig 0x%x
205572
Ethernet device could not be
configured.
ErrorNICQL3xxx:ql3xxx_probe: cannot
allocate ethernet device %s
206080
The Ethernet port was not able to
register as a network device, resulting
ErrorNICQL3xxx:ql3xxx_probe: cannot
register network device %s
206089
in a port initialization error for the
specified network device.
The total number of TCP checksum
errors detected on the Ethernet link
belonging to the eth#%d port.
ErrorNICQL3xxx:eth%d: TCP/IP checksum
error - TotalChecksumErrorCount
= %lu
206114
Ethernet port is operating at 100Mbps
speed.
InfoNICQL3xxx:%s: PHY Downshift
occurred
217856
Ethernet link is up.InfoNICQL3xxx:%s: Link Up217857
Ethernet link is down.InfoNICQL3xxx:%s: Link Down217858
Ethernet port is down.InfoNICQL3xxx:%s Adapter Down218389
Ethernet port is up.InfoNICQL3xxx:%s Adapter Up218401
Uncorrectable memory error detected
at address provided in log message.
FatalSystem"memory monitor: Detected
Uncorrectable Ecc %08lx system
is rebooting in 5 secs\n"
233473
Attempt to register the interrupt
handler failed.
FatalSystem"Failed to register interrupt
handler!\n"
233474
Failed class_simple_create
system call from memory monitor
initialization routine.
FatalSystem"%s class_simple_create
failed\n"
233475
Failed to kill system task.ErrorSystem"Failed to kill sys killer
%d\n"
237572
Router temperature has exceeded the
high temperature threshold.
ErrorSystemTemperature over high threshold
%d
237573
Router temperature has returned to the
normal operating range.
InfoSystemTemperature is back to normal
range %d
249862
Table 35 DM log messages
DescriptionMsg typeModule typeLog MessageID
An error occurred on an I/O that
was issued for a migration job.
ErrorAppQLDM_HandleMigError: Migration
Job %d stopped for Src Lun %hd
44549
The description provides the job
Dest Lun %hd Error %x
232 Log messages
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Contents 9 9
- MPX200 features 10
- MPX200 storage system support 10
- Management software 12
- Installation recommendations 20
- Total number of initiators 21
- Use of iSNS 21
- Use of iSCSI ports 21
- Balancing the load 21
- 10-GbE initiators 22
- Prerequisites 22
- General IP-SAN 23
- Network latency 25
- 3 Installing the MPX200 26
- Rack mounting the MPX200 27
- 1. Power cord 29
- Rack mounting the MPX200 29 29
- 4. Bezel3. Bracket arrows 30
- 30 Installing the MPX200 30
- Fibre Channel zoning 31
- Setting up the iSCSI IP ports 34
- Code load 36
- Locating the MPX200 38
- Removing an iSCSI controller 39
- Setting up the iSCSI ports 41
- LUN provisioning 42
- LUN provisioning 43 43
- Alternate procedure 45
- LUN management 48
- LUN management 49 49
- Figure 48 Expanded ports 50
- LUN management 51 51
- Supported IP network adapters 58
- IP network requirements 58
- Figure 56 Host details 63
- Multipathing 65
- Assigning device names 78
- Target bindings 78
- Mounting file systems 79
- Unmounting file systems 79
- MPxIO overview 83
- Editing the sgen.conf file 85
- Creating an sgen driver alias 86
- #mpathadm list lu 88
- Setting up authentication 97
- Setting up authentication 103 103
- Setting up authentication 107 107
- 8 MPX200 FCIP 108
- FCIP and iSCSI performance 110
- 112 MPX200 FCIP 112
- 114 MPX200 FCIP 114
- 116 MPX200 FCIP 116
- 118 MPX200 FCIP 118
- IP performance tuning 121
- Distance 122
- Bandwidth per route 122
- MTU/Jumbo frames 122
- Compression 123
- FCIP link diagnostics 126
- Configuring an FCIP route 127
- Step 3. Rack-mount the MPX200 128
- Step 4. Install the SFPs 128
- Install FCIP license 129
- Configuring an FCIP route 131 131
- 132 MPX200 FCIP 132
- FCoE configurations 133
- Ethernet 134
- Figure 114 Host type 137
- Figure 115 Host properties 137
- MPX200 chassis diagnostics 141
- Fibre Channel Port LEDs 142
- POST diagnostics 142
- Locating the MPX200 blade 144
- MPX200 log data 144
- MPX200 statistics 144
- MPX200 ping command 144
- WANLink diagnostic 145
- Issues and solutions 147
- Intended audience 151
- Related documentation 151
- Contacting HP 151
- Related information 152
- Typographical conventions 152
- Rack stability 153
- Product warranties 153
- 12 Documentation feedback 154
- A Command reference 155
- Fciproute 158
- Example 2: 159
- NoneAuthority 161
- Commands 161 161
- Initiator 163
- Commands 165 165
- Set alias 169
- Set CHAP 169
- Set chassis 170
- Commands 171 171
- Set features 172
- Set iSCSI 172
- Set iSNS 172
- Set Mgmt 173
- Set properties 174
- Set SNMP 174
- Set system 175
- Set VPGroups 175
- Show CHAP 178
- Show chassis 178
- Show fciproutes 179
- Show features 180
- Show initiators 180
- Show initiators LUNmask 180
- Show iSCSI 181
- Show iSNS 181
- Show logs 182
- Show LUNinfo 182
- Show LUNs 183
- Show LUNmask 183
- Show memory 184
- Show mgmt 184
- Show NTP 184
- Show perf 185
- Show presented targets 186
- Show properties 187
- Show SNMP 187
- Show stats 187
- 188 Command reference 188
- Commands 189 189
- Show system 190
- Show targets 190
- Show VPGroups 191
- Shutdown 191
- Traceroute 192
- Wanlinktest 192
- 194 Command reference 194
- Logging on to an MPX200 195
- Modifying a configuration 196
- SNMP parameters 199
- Management Information Base 200
- FC port table 202
- Initiator object table 204
- LUN table 205
- VP group table 207
- Sensor table 209
- Notifications 210
- Notification objects 211
- Agent startup notification 212
- Agent shutdown notification 212
- FC port down notification 212
- Target device discovery 212
- Notifications 213 213
- Notifications 215 215
- D Log messages 216
- Table 35 DM log messages 232
- Table 36 WD log messages 235
- Regulatory compliance notices 240
- BSMI notice 241
- Safety notices 242
- Power cords 243
- Japanese power cord statement 244
- Chinese warning messages 244
- English notice 244
- Dutch notice 244
- Czechoslovakian notice 245
- Estonian notice 245
- Finnish notice 245
- French notice 245
- German notice 245
- Greek notice 246
- Hungarian notice 246
- Italian notice 246
- Latvian notice 247
- Lithuanian notice 247
- Polish notice 247
- Portuguese notice 247
- Slovakian notice 248
- Slovenian notice 248
- Spanish notice 248
- Swedish notice 248
- Username: guest 250
- Password: password 250
- MPX200> admin start 250
- Glossary 251
- 252 Glossary 252
- 254 Glossary 254
- 256 Index 256
- 258 Index 258
Verwandte Produkte und Handbücher für Lager Hp MPX200 Multifunction Router
Lager Hp X500 Data Vault Bedienungsanleitung
(331 Seiten)
(331 Seiten)
Lager Hp XP7 Storage Bedienungsanleitung
(208 Seiten)
(208 Seiten)
Lager Hp XP P9500 Storage Bedienungsanleitung
(116 Seiten)
(116 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern