Hp UPS Extended Runtime Module Bedienungsanleitung

HP UPS R3000 User Guide Part Number 192131-007 December 2009 (Seventh Edition)

Component identification 10 Item Description 8 PDU output (NEMA L5-30) receptacle (load segment 1) 9 Cord retention clip attachment locations 10

Component identification 11 UPS R3000 INT rear panel Item Description 1 REPO port 2 ERM connector 3 Serial communications port/options slot

Component identification 12 NOTE: If the UPS was operating on battery power when the remote switch was closed, no power is available to the load d

Installation 13 Installation Precautions Save these instructions. This document contains important safety instructions that should be followed durin

Installation 14 • Hex nuts • Cage nuts • Cage nut-fitting tool Selecting a site WARNING: To prevent fire or electric shock, install the unit

Installation 15 WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling feet are extended to the

Installation 16 2. Insert screws through the rack into the mounting rail and the front of each mounting bracket. 3. Install cage nuts or clip nuts

Installation 17 4. Insert screws through the mounting rail into the cage nuts or clip nuts. 5. Tighten the wing nuts or hex nuts.

Installation 18 6. Install the rear stabilization bracket using hex nuts. Wait until the unit is installed and the brackets are adjusted before tigh

Installation 19 Connecting the battery leads Attaching the UPS front bezel Connecting the serial communications port CAUTION: Use only the c

© Copyright 2000, 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warr

Installation 20 Connecting the REPO port WARNING: The pins on the REPO port are polarity sensitive. Be sure to verify polarity while connect

Installation 21 NOTE: Wire the connector block using stranded, nonshielded wire (AWG #22 - #18, or equivalent). Separate wire pairs are att

Installation 22 Connecting the ground bonding cable NOTE: UPS appearance might vary depending on the specific unit installed. The ground bond

Installation 23 WARNING: To prevent injury from electric shock or damage to the equipment: • Plug the input line cord into a grounded (earthed) e

Installation 24 Charging the UPS batteries Allow the batteries to charge before putting the UPS into service. IMPORTANT: Charge the batteries fo

Installation 25 Attaching the ERM front bezel Switching off the ERM circuit breaker WARNING: To prevent personal injury from electric shock or

Installation 26 Plug the ERM cable (1) in the socket (2) at the rear of the UPS. NOTE: To install a second ERM, plug the cable from the second

UPS operations 27 UPS operations Modes of operation The UPS has four modes of operation: • Standby mode (on page 27) • Operate mode (on page 27) •

UPS operations 28 NOTE: • If the UPS is using battery power (no utility power is present and the Utility LED is red), press and hold the On but

UPS operations 29 Available settings Parameter Associated LED Explanation (when LED is illuminated) Nominal voltage setting 100/200-208 Nom

Contents Component identification ... 6

UPS operations 30 NOTE: Configure mode times out after 2 minutes of inactivity. If the Test/Alarm Reset button has not been pressed, any new sel

UPS operations 31 Silencing an audible alarm To silence an alarm, press the Test/Alarm Reset button ("UPS front panel controls" on page 7)

Power management 32 Power management Power management software HP Power Manager software ensures maximum power reliability of computer systems throu

Maintenance 33 Maintenance Removing the UPS front bezel Removing the ERM front bezel Replacing the UPS electronics module This component is hot-

Maintenance 34 1. (optional) To replace the component with the UPS powered down, refer to "Powering down the UPS (on page 31)." 2. Disc

Maintenance 35 3. Remove the two screws securing the option card and slide the card out. To replace the component, reverse the removal procedure.

Maintenance 36 WARNING: To prevent personal injury, prepare the area and observe all materials-handling procedures when transporting a battery mod

Maintenance 37 1. (optional) To replace the component with the UPS powered down, refer to "Powering down the UPS (on page 31)." CAUTI

Maintenance 38 Testing the new battery module After installing the new battery module, press the Test/Alarm Reset button to initiate a self-test (&q

Maintenance 39 1. Switch the circuit breaker for any attached ERMs to the Off position. 2. Unplug the ERM from the back of the UPS. 3. Unplug the

Verifying the REPO port connection ... 31

Maintenance 40 9. Click Advanced. The Advanced Settings screen appears. 10. From the COM Port Number drop down menu, select Com 1 for the USB port

Troubleshooting 41 Troubleshooting LED and audible alarm troubleshooting General Alarm LED On Battery LED Battery Fault LED Site Wiring Fa

Troubleshooting 42 Off Flashing red Off Off Flashing red Off On—1 beep every 5 seconds Yes On battery—Input voltage is out of range (on page 43) Fl

Troubleshooting 43 b. Remove one or more load devices to reduce the power requirements. c. Wait at least 5 seconds and restart the UPS. d. If the

Troubleshooting 44 Utility power condition The utility input voltage is outside the operating range. Action: 1. Check the input voltage and reconfi

Troubleshooting 45 1. Be sure that the power cord is plugged in to a utility power receptacle. 2. Check the power source at the utility power recep

Specifications 46 Specifications UPS physical specifications Parameter Value Height 8.9 cm (3.5 in) Depth 62.2 cm (25 in) Width 44.1 cm (17.

Specifications 47 1The output voltage is 204 for this setting. UPS output specifications UPS model Load segment Output receptacles R3000 N

Specifications 48 Configuration setting (VAC) Available nominal output voltage (VAC) 208 208 230 230 240 240 Output tolerance specifications

Specifications 49 Environmental specifications Feature Specification Operating temperature 10°C to 40°C (50°F to 104°F); UL-tested at 25°C (77°F

REPO port specifications ...

Spares 50 Spares Ordering spares To order a spare, visit the HP website (http://www.hp.com/buy/parts). To replace parts under warranty, contact an H

Spares 51 * not shown ERM spare parts list Item Description Spare part number 1 Battery modules (2) 407407-001 2 ERM unit 407398-001 *

Technical support 52 Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical su

Warranty information 53 Warranty information Limited warranty To back up the wide range of features offered with the UPS, a 3-year limited warranty

Warranty information 54 Recommended duration of use Although tests and a multitude of customer experiences have shown no noticeable performance issu

Regulatory compliance notices 55 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance

Regulatory compliance notices 56 to radio communications. However, there is no guarantee that interference will not occur in a particular installati

Regulatory compliance notices 57 Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Cana

Regulatory compliance notices 58 This symbol on the product or on its packaging indicates that this product must not be disposed of with your other

Regulatory compliance notices 59 BSMI notice Korean notice Class A equipment Class B equipment Battery replacement notice WARNING: Power pr

Component identification 6 Component identification UPS R3000 overview The HP UPS R3000 features a 2U rack-mount design and offers power protection

Regulatory compliance notices 60 Taiwan battery recycling notice The Taiwan EPA requires dry battery manufacturing or importing firms in accordance

Electrostatic discharge 61 Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions yo

Acronyms and abbreviations 62 Acronyms and abbreviations ERM extended runtime module IEC International Electrotechnical Commission LED light-emitt

Index 63 A alarm cannot be silenced 41 alarms, silencing 31 authorized reseller 52 Auto-Bypass mode 28, 42 B backup time, insufficient 45

Index 64 front panel components 6, 7 front panel LEDs 8 G general alarm condition 42 General Alarm LED, location 8 General Alarm LED, troubl

Index 65 R3000j JPN 9 rails, installing 14 rear panel connectors 9, 10, 11, 12 recommended duration of use 54 regulatory compliance identifi

Component identification 7 UPS front panel controls The front panel is shown with the bezel removed. Item Description Function 1 On butto

Component identification 8 UPS front panel LED indicators The front panel is shown with the bezel removed. Item LED description 1 Configu

Component identification 9 UPS model Description R3000j JPN ("UPS R3000 NA and R3000j JPN rear panel" on page 9) • Japanese • Low-volta