Hp StorageWorks 3000 RAID Array Bedienungsanleitung Seite 77
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation and Maintenance 3-15
Compaq Confidential – Need to Know Required
Writer: Bob Young Project: RAID Array 3000 Controller Shelf Hardware User’s Guide Comments:
Part Number: EK-SMCPQ-UG. D01 File Name: d-ch3 Installation and Maintenance.doc Last Saved On: 12/4/00 1:08 PM
Cabling a Single Device Expansion Shelf
Subsystem
1. Ensure the physical installation phase of installing and securing shelf
brackets and shelves (including the UPS) has been accomplished and
that the shelves are secured within the shelf bracket the shelf lock
provided.
2. Remove the device I/O module from the controller shelf and ensure the
switch positions of SCSI bus termination switch S4 are set as shown in
Figure 3-9. Replace the module in the controller shelf.
3. Remove the personality I/O module from the device expansion shelf and
set SCSI bus termination switch S4 on this module as shown in
Figure 3-9.
4. Ensure SCSI bus address switch S3 on the personality I/O module is set
for the device addresses as shown in Figure 3-9. Replace the module in
the device expansion shelf.
5. Connect the black AC power cords (supplied with the shelves) from the
AC power source to the outside power supply on each shelf
(see Figure 3-10).
6. Connect the gray power cables from the inside power supply on each
shelf to the power receptacles on the back of the UPS (ensure the UPS is
connected to an AC source).
7. Connect a 0.5-meter SCSI cable (BN37A-0E) from the top SCSI
connector on the Controller shelf device I/O module (device bus 1) and
the SCSI connector on the front of the personality I/O module on the
expansion shelf.
8. Connect a 5-meter SCSI cable (BN37A-05) between the host-in
connector on the controller shelf host 0 I/O module (bottom connector)
and the corresponding connector on the host system.
9. Connect the maintenance serial control cable (17-04730-01) from the
CTR 0 connector on the controller shelf host 0 I/O module to the
corresponding connector on the maintenance PC.
10. Connect the UPS serial control cable (17-04729-01) from the UPS
connector controller shelf host 0 I/O module to the like connector on the
UPS.
11. Install jumper connector 12-49700-01 to the controller shelf UPS
connector on the host 1 I/O module.
- Compaq StorageWorks 1
- Contents 3
- Chapter 2 4
- Chapter 3 4
- Chapter 4 5
- List of Figures 5
- List of Tables 7
- About This Guide 9
- Related Documents 11
- Text Conventions 12
- Symbols in Text 12
- Symbols on Equipment 13
- Rack Stability 14
- Getting Help 14
- Compaq Website 15
- Compaq Authorized Reseller 15
- Product Overview 17
- Table 1-1 20
- Product Overview 1-5 21
- Controller Shelf Features 22
- Controller Shelf Enclosure 22
- SHR-1051b 23
- Shelf Cabinet 24
- Device I/O Module 25
- Host I/O Module 28
- Shelf Cooling 29
- Figure 1-8. Power supply 30
- Table 1-2 33
- Table 1-3 34
- Table 1-4 35
- Table 1-5 36
- Specifications 37
- Table 1-6 38
- Product Overview 1-23 39
- Table 1-7 40
- Product Overview 1-25 41
- RAID Array 3000 Controller 43
- Controller Features 45
- Table 2-1 47
- LED/Reset Switch Interface 47
- Reset H0 D0H1 D1 Fault 48
- Custom Components 49
- Write-Back Caching 50
- Write Gathering 50
- Write On Top 50
- RAID Levels Supported 51
- Figure 2-5. RAID 0 write 52
- RAID 0+1 54
- Table 2-4 55
- RAID 0+1 Example 55
- Redundant Operation 59
- Initialization 60
- Message Passing 60
- Failover 60
- Environmental 61
- Installation and Maintenance 63
- Metric cabinet 69
- Installation 69
- UPS installation into a 69
- RETMA or metric 69
- (Round Hole) 70
- Table 3-2 70
- (Square Hole) 71
- Installing UPS Brackets 72
- Table 3-3 73
- Procedures 75
- Subsystem 77
- DEVICE EXPANSION SHELF # 1 78
- CONTROLLER SHELF 78
- DEVICE EXPANSION SHELF #1 79
- DEVICE EXPANSION SHELF # 2 81
- DEVICE EXPANSION SHELF # 3 83
- DEVICE EXPANSION SHELF # 4 85
- Controller Shelf Status LED’s 86
- Controller Status LEDs 87
- Table 3-4 89
- Replacing a Power Supply SBB 91
- Replacing the RAID Controller 92
- Replacing the UPS 93
- Replacing a Blower 93
- Second Controller Option 99
- Installing the Upgrade 100
- Updating Firmware 102
- Shutting down the RA3000 104
- Replace Existing Controller 106
- Restoring the Configuration 107
- Operation 109
- HSZ22 Storage window 111
Verwandte Produkte und Handbücher für Lager Hp StorageWorks 3000 RAID Array
Lager Hp XP7 Storage Bedienungsanleitung
(123 Seiten)
(123 Seiten)
Lager Hp X500 Data Vault Bedienungsanleitung
(331 Seiten)
(331 Seiten)
Lager Hp XP7 Storage Bedienungsanleitung
(208 Seiten)
(208 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.246 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern