Hp Onboard Administrator Bedienungsanleitung

HP BladeSystem Onboard Administrator Command Line Interface User Guide Abstract This guide details using the command-line interface for configur

Contents 10 SET VLAN IPCONFIG STATIC ...

Enclosure network configuration commands 100 SET OA NAME • Command: SET OA NAME [<bay number> | ACTIVE | STANDBY] "<OA name>"

Enclosure network configuration commands 101 SET SERIAL BAUD [ 9600 | 19200 | 38400 | 57600 | 115200] • Description: Configures the baud rate sett

Enclosure network configuration commands 102 • Example: OA> set snmp engineid testid SNMP engine id set to "0x8000000b04746573746964"

Enclosure network configuration commands 103 o In ON mode, Onboard Administrator is in a FIPS 140-2-compliant mode, using only FIPS 140-2 approved a

Enclosure network configuration commands 104 info. It could take up to 3

Enclosure network configuration commands 105 4 OK 5 OK 6 OK 7 OK 8 OK 9 OK 10 OK Onboard Administrator Health: Bay Status

Enclosure network configuration commands 106 o IPv4 information o IPv6 information o DHCP state o SLAAC o Dynamic DNS state o Static Default Ga

Enclosure network configuration commands 107 - - - - - IPv4 Information - - - - - DHCP: Enabled - Dynamic DNS IPv4 Address:

Enclosure network configuration commands 108 SHOW SNMP • Command: SHOW SNMP • Description: Displays the SNMP configuration, including: o SNMP sys

Enclosure network configuration commands 109 • Example: OA> show snmp user list SNMPv3 User Local Access Security EngineI

Introduction 11 Introduction What's new The following changes have been made to this guide, published with the release of Onboard Administrator

Enclosure network configuration commands 110 SHOW VCMODE • Description: Displays Virtual Connect Mode settings • Access level/Bay level: All • Re

Enclosure management commands 111 Enclosure management commands ADD LANGUAGE • Command: ADD LANGUAGE <URL> • Description: o Uploads and ins

Enclosure management commands 112 • Description: Connects to the OA CLI on a linked enclosure. To get a list of linked enclosure names, use the SHO

Enclosure management commands 113 DISABLE LLF • Description: Disables Link Loss Failover for Onboard Administrator Redundancy. • Access level/Bay

Enclosure management commands 114 • Description: Enables Link Loss Failover for Onboard Administrator Redundancy. • Access level/Bay level: Operat

Enclosure management commands 115 o hh: Hour (24-hour time) o mm: Minute o CC: Century o YY: Year o TZ: Time zone If you leave the time zone var

Enclosure management commands 116 The <asset tag> must be 0 to 32 characters long and includes all alphanumeric, underscore (_), and dash (-)

Enclosure management commands 117 OA administrator • Restrictions: 1, 2, 3, 4, 5 SET ENCLOSURE SERIAL_NUMBER • Command: SET ENCLOSURE SERIAL_NUMB

Enclosure management commands 118 SET OA DOMAIN_NAME • Command: SET OA DOMAIN_NAME [ <bay number> | active | standby ] {“<domain-name>”

Enclosure management commands 119 The FRONT controller enables the internal DVD drive and the front USB connector. The BACK controller enables the t

Introduction 12 • The SET EBIPAV6 SERVER command line and restrictions were updated. • The SET FACTORY command description was updated. • The SET

Enclosure management commands 120 • Description: o Turns power savings mode on or off. Enabling power savings (specify ON) turns unneeded power su

Enclosure management commands 121 #Generated on: Tue Apr 15 10:34:32 2008 #Set Enclosure Time SET TIMEZONE CST6CDT #SET DATE MMDDhhmm{{CC}YY} #Set E

Enclosure management commands 122 SHOW DISPLAY EVENTS • Description: Displays whether event notification is on or off • Access level/Bay level: Al

Enclosure management commands 123 o Enclosure name o Enclosure type o Onboard Administrator hardware version o Enclosure Rack U Position o Enclo

Enclosure management commands 124 Name : BladeSystem c3000 Insight Display Spare Part# : 441831-001 Manufacturer: HP

Enclosure management commands 125 ------- = 1314 Interconnect Bay Power Summary: Bay

Enclosure management commands 126 Spare Part Number: XXXXXX-001 Product Ver: Diagnostic Status: Internal Dat

Enclosure management commands 127 • Access level/Bay level: All Bay specific • Restrictions: None • Example: OA-0018FE27577F> SHOW ENCLOSURE T

Enclosure management commands 128 Firmware Version: 2.40 HwVersion: A0 Blade 1 Model: ProLiant BL480c G1 Manufact

Enclosure management commands 129 Model: Active Cool 200 Fan Part Number: 412140-B21 Spare Part Number: 413996-001 Fan 6

Accessing the command line interface 13 Accessing the command line interface Remote access to the Onboard Administrator The Onboard Administrator CL

Enclosure management commands 130 SHOW OA • Command: SHOW OA {CERTIFICATE | INFO | NETWORK | STATUS | UPTIME | USB} [ALL | <bay number> [{ ,

Enclosure management commands 131 SHOW OA INFO [ALL | <bay number> [{ , | - } <bay number>] | ACTIVE | STANDBY]] • Description: Display

Enclosure management commands 132 DHCPv6: Disabled Stateless address autoconfiguration (SLAAC): Enabled Onboard Administrator #1 Ne

Enclosure management commands 133 Name: OA-0018FE27577F Role: Active UID: Off Status: OK Diagnostic Status

Enclosure management commands 134 Onboard Administrator USB setting = FRONT SHOW POWER • Command: SHOW POWER • Description: Displays the current

Enclosure management commands 135 COUNT="1" DESCRIPTION="IML Cleared (iLO user:Administrator)" OA-0016355E560A> SHOW SYSLOG

Enclosure management commands 136 Apr 2 19:30:27 in.ftpd[31245]: Can't change directory to standby.xml: No such file or directory Apr 2 19:3

Enclosure management commands 137 UPDATE • Command: UPDATE {IMAGE | ILO | SHOW | DEVICE | FIRMWARE } • Description: o The UPDATE SHOW (or SHOW UP

Enclosure management commands 138 ICBAY | HP 4Gb Fibre Channel Pass-thru Module for c-C | 6A | 2.4.3 | 2.10.3 ICBAY | HP 4Gb Fibre Channel

Enclosure management commands 139 o Updates the Onboard Administrator firmware using an image on a firmware CD. Enclosure Firmware Management must b

Accessing the command line interface 14 Pin Name Signal direction Description 4 DTR -->> Data terminal ready 5 GND System ground 6 DSR

Enclosure management commands 140 UPLOAD SUPPORTDUMP • Command: UPLOAD SUPPORTDUMP {"<url>"} • Description: o Uploads supportdump

Enclosure Firmware Management commands 141 Enclosure Firmware Management commands DISCOVER FIRMWARE SERVER • Command: DISCOVER FIRMWARE SERVER { AL

Enclosure Firmware Management commands 142 SET FIRMWARE MANAGEMENT { URL | POLICY | POWER | SCHEDULE | BAYS_TO_INCLUDE | FORCE DOWNGRADE } • Descri

Enclosure Firmware Management commands 143 • Access level/Bay level: OA administrator • Restrictions: o OFF—The server must be powered off or the

Enclosure Firmware Management commands 144 o The bays_to_include feature only applies to ProLiant server blades. Integrity server blades do not supp

Enclosure Firmware Management commands 145 • Example: OA-00215AB0EA21> show firmware management Enclosure Firmware Settings Enclosure:

Enclosure Firmware Management commands 146 You must have access to the specified bay number. • Example: iLO2 1.81

Enclosure Firmware Management commands 147 System ROM I19 07/10/2009 iLO2 1.79 Aug 28

Enclosure Firmware Management commands 148 12, ProLiant BL495c G6, Mon 2010-09-13 17:18:28, System ROM, A14 2009.12.09, A14 2009.12.09, ILO2, 1.81,

Enclosure Firmware Management commands 149 SHOW FIRMWARE LOG SESSION • Command: SHOW FIRMWARE LOG SESSION { ALL | <bay number> [{ , | - } <

Command line 15 Command line Command line overview The CLI can be used as an alternative method for managing the Onboard Administrator. Using the CL

Enclosure Firmware Management commands 150 UPDATE FIRMWARE SERVER • Command: UPDATE FIRMWARE SERVER { ALL | <bay number> [{ , | - } <bay n

Blade management commands 151 Blade management commands CONNECT SERVER • Command: CONNECT SERVER [SERIAL] <bay number> • Description: Opens

Blade management commands 152 f. Finish the command with the end marker. To view the RIBCL script that will be sent to the iLO, specify TEST. • Acc

Blade management commands 153 POWEROFF SERVER CAUTION: This command can cause a server blade to lose data or become unstable. • Command: POW

Blade management commands 154 REBOOT SERVER • Command: REBOOT SERVER { ALL | <bay number> [{ , | - } <bay number>]} [FORCE] [{ NORMAL |

Blade management commands 155 o SET SERVER BOOT ONCE (on page 155) sets the boot device to be used on the next boot of the bays specified. • Access

Blade management commands 156 • Description: o Stores a setting for the IPL to be passed to the specified servers at the next reboot. o HDD sets

Blade management commands 157 Bay specific • Restrictions: You must have access to the specified bay number. SHOW SERVER BOOT • Command: SHOW SER

Blade management commands 158 o NICs name and slot number o iLO name, iLO IP address, and iLO firmware version o Power Management Controller versi

Blade management commands 159 Management Processor IPv6 Information: Link Local Address: fe80::9e8e:99ff:fe17:21e/64 Static Address:

Command line 16 • TEST Because these words indicate specific functions within the Onboard Administrator firmware, they are only allowed where expli

Blade management commands 160 10 ILOMXQ1281CDZ fe80::9e8e:99ff:fe17:b0f9 LL

Blade management commands 161 Displays the port mapping for the server specified by the bay number • Access level/Bay level: All Bay specific • Re

Blade management commands 162 <absent> ------------------------------- Blade 006 ------------------------------- <absent> ----------

Blade management commands 163 8 AiO SB600c Storage Disabled 0 8A Absent Disabled

Blade management commands 164 Power OK Cooling OK Location O

Blade management commands 165 SHOW SERVER TEMP {ALL | <bay number> [{ , | - } <bay number>]} • Description: Displays the temperature se

Blade management commands 166 CPU Zone OK 35C/ 95F 70C 75C CPU 2 OK

Blade management commands 167 INITIAL_UPDATE="10/08/2007 01:31" COUNT="1" DESCRIPTION="Server Blade Enclosure LAN Set

Interconnect management commands 168 Interconnect management commands ASSIGN INTERCONNECT • Command: ASSIGN INTERCONNECT {ALL | <bay number>

Interconnect management commands 169 You must have explicit access to a bay given by the ASSIGN INTERCONNECT command. POWEROFF INTERCONNECT • Comm

Command line 17 Account classification Capabilities Account name / Privilege level Bays selected for this account password recovery option • Can

Interconnect management commands 170 SET INTERCONNECT ADMIN_PASSWORD FACTORY • Command: SET INTERCONNECT ADMIN_PASSWORD FACTORY [<bay number>

Interconnect management commands 171 • Restrictions: You must have access to the specified bay number. SET INTERCONNECT POWERDELAY • Command: SET

Interconnect management commands 172 — Product name — Product part number — Product version — Product serial number — Asset tag — VLAN ID o I

Interconnect management commands 173 SHOW INTERCONNECT INFO • Command: SHOW INTERCONNECT INFO {PORT MAP | POWERDELAY | SESSIONS | STATUS} [ALL | &l

Interconnect management commands 174 IPv6 Information: LL Address: fe80::223:7dff:fe43:9c4e/64 LL URL: http://[fe80::223:7d

Interconnect management commands 175 External Serial Port Interface: Absent External Ethernet Interface: Absent Manufacturer

Interconnect management commands 176 Totals: 2 interconnect modules installed, 2 powered on. SHOW INTERCONNECT PORT MAP • Command: SHOW INTERCONNE

Interconnect management commands 177 Current PowerDelay Status: Not in Progress Bay Device PowerDelay State Delay (seco

Interconnect management commands 178 Internal Data OK Management Processor OK Thermal Warning

Active Health System commands 179 Active Health System commands ENABLE ACTIVE HEALTH SYSTEM • Command: ENABLE ACTIVE_HEALTH_SYSTEM • Description:

Command line 18 Account classification Capabilities Account name / Privilege level Bays selected for this account information of enclosure • Can

Enclosure DVD commands 180 Enclosure DVD commands SET SERVER DVD • Command: SET SERVER DVD {CONNECT | DISCONNECT} [USB://url] {ALL | <bay number

Enclosure DVD commands 181 5 - [Bay empty] 6 - [Bay empty] 7 No 8 - [Non-server blade]

Remote syslog commands 182 Remote syslog commands DISABLE SYSLOG REMOTE • Command: DISABLE SYSLOG REMOTE • Description: Disables remote system log

Remote syslog commands 183 SET REMOTE SYSLOG SERVER • Command: SET REMOTE SYSLOG SERVER {<IPv4/IPv6> | <dns name>} • Description: Sets

Remote syslog commands 184 Remote syslog example The remote syslog consists of a date and time stamp, the Onboard Administrator IP address, text, an

USB support commands 185 USB support commands DOWNLOAD CONFIG using USB key • Command: DOWNLOAD CONFIG <url> • Description: Downloads a save

USB support commands 186 • Description: Displays a list of Firmware images, configuration scripts, and ISO images present on the enclosure USB medi

USB support commands 187 You cannot use the FORCE option for downgrade in FIPS Mode ON/DEBUG. CAUTION: When a firmware upgrade is in process, do

VLAN commands 188 VLAN commands ADD VLAN • Command: ADD VLAN <VLAN ID> ["<VLAN NAME>"] • Description: Creates a VLAN ID and

VLAN commands 189 ENABLE VLAN • Command: ENABLE VLAN • Description: This command enables or turns on VLAN on the enclosure. • Access level/Bay le

Command line 19 iLO privileges administrator operator user Administer user accounts X Remote console access X X Virtual power and reset X

VLAN commands 190 • Access level/Bay level: OA administrator, OA operator • Restrictions: The VLAN ID is a value between 1 and 4094. SET VLAN FAC

VLAN commands 191 • Access level/Bay level: OA administrator, OA operator • Restrictions: None SET VLAN IPCONFIG DHCP • Command: SET VLAN IPCONF

VLAN commands 192 SET VLAN OA • Command: SET VLAN OA <VLAN ID> • Description: Sets or changes the VLAN ID of the Onboard Administrator. Loss

VLAN commands 193 SHOW VLAN • Description: Shows VLAN settings. • Access level/Bay level: OA administrator, OA operator, OA user • Restrictions:

HP Insight Remote Support commands 194 HP Insight Remote Support commands ADD REMOTE_SUPPORT CERTIFICATE • Command: ADD REMOTE_SUPPORT CERTIFICATE

HP Insight Remote Support commands 195 o Specify the URL where the certificate can be found. o Supported protocols are HTTP, FTP, and TFTP. o Form

HP Insight Remote Support commands 196 REMOTE_SUPPORT (on page 200) command to send a test event to confirm the connection between OA and Insight Re

HP Insight Remote Support commands 197 DISABLE REMOTE_SUPPORT • Command: DISABLE REMOTE_SUPPORT • Description: Unregisters the Onboard Administrat

HP Insight Remote Support commands 198 Remote Support must be enabled before sending a data collection. If the enclosure contains a large number of

HP Insight Remote Support commands 199 Displays Remote Support settings and information such as: o Remote Support status o Connection type: DIRECT

© Copyright 2006, 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only war

General commands 20 General commands CLEAR SCREEN • Command: CLEAR SCREEN • Description: Clears the terminal screen • Access level: Administrator

HP Insight Remote Support commands 200 subjectOrganization = Hewlett-Packard Company subjectOrganizationalUn

HP Insight Remote Support commands 201 • Restrictions: Remote Support must be enabled before sending a test event. If the enclosure contains a larg

Enclosure Dynamic Power Cap commands 202 Enclosure Dynamic Power Cap commands SET ENCLOSURE POWER_CAP • Command: SET ENCLOSURE POWER_CAP { <cap&

Enclosure Dynamic Power Cap commands 203 If you have previously specified bays to exclude, using this command again replaces that specification rath

Event notifications 204 Event notifications Enclosure event notifications Enclosure events produce screen messages with the show events option enabl

Event notifications 205 Event Cause Fan Status Change The status of a fan has changed. Fan Inserted A fan has been inserted. Fan Removed A fan has

Event notifications 206 Event Cause User Rights The privilege level of a user on the Onboard Administrator was changed. If you are logged in as thi

Support and other resources 207 Support and other resources Before you contact HP Be sure to have the following information available before you cal

Time zone settings 208 Time zone settings Universal time zone settings IMPORTANT: Time zones must be entered exactly as they appear. The follo

Time zone settings 209 Africa/Cairo Africa/Khartoum Africa/Nairobi — Africa/Casablanca Africa/Kigali Africa/Ndjamena — Americas time zone settin

General commands 21 LOGOUT • Description: Exits the command line interpreter • Access level: Administrator, Operator, User QUIT • Command: QUIT

Time zone settings 210 America/Campo_Grande America/Martinique America/Yellowknife America/Cancun America/Matamoros Brazil/Acre America/Caracas Ame

Time zone settings 211 Asia/Amman Asia/Dubai Asia/Krasnoyarsk Asia/Riyadh Asia/Urumqi Asia/Anadyr Asia/Dushanbe Asia/Kuala_Lumpur Asia/Riyadh87 A

Time zone settings 212 Australia/Darwin Indian/Kerguelen Pacific/Honolulu Pacific/Tongatapu Australia/Eucla Indian/Mahe Pacific/Johnston Pacific/T

Time zone settings 213 Antarctica/Davis Antarctica/McMurdo Antarctica/Syowa Antarctica/DumontDUrville Antarctica/Palmer Antarctica/Vostok Antarctic

Acronyms and abbreviations 214 Acronyms and abbreviations BLD BladeSystem Location Device CA certificate authority DDNS Dynamic Domain Name System

Acronyms and abbreviations 215 HP SIM HP Systems Insight Manager HTTPS hypertext transfer protocol secure sockets ICMP Internet Control Message Pr

Acronyms and abbreviations 216 RSA Rivest, Shamir, and Adelman public encryption key SLAAC stateless address autoconfiguration SOAP Simple Object

Documentation feedback 217 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documenta

Index 218 A accessing the CLI 13 account authentication 18 account level 16 ADD CA CERTIFICATE 34 ADD EBIPA 60 ADD EBIPAV6 60 ADD HPSIM

Index 219 command, DISABLE FIRMWARE MANAGEMENT 141 command, DISABLE FQDN_LINK_SUPPORT 82 command, DISABLE GUI_LOGIN_DETAIL 112 command, DISABL

Rack commands 22 Rack commands SET RACK NAME • Command: SET RACK NAME <rack name> • Description: Sets the rack name • Access level/Bay leve

Index 220 command, REMOVE TRUSTED HOST 94 command, REMOVE USER 28 command, REMOVE USER CERTIFICATE 36 command, REMOVE VLAN 189 command, REST

Index 221 command, SET USER PASSWORD 30 command, SET VLAN DEFAULT 189 command, SET VLAN FACTORY 190 command, SET VLAN INTERCONNECT 190 comma

Index 222 command, TEST REMOTE_SUPPORT 200 command, TEST SNMP 110 command, TEST SYSLOG 183 command, TEST URB 59 command, UNASSIGN 32 comma

Index 223 ENABLE SLAAC 91 ENABLE SNMP 91 ENABLE STRONG PASSWORDS 26 ENABLE SYSLOG REMOTE 182 ENABLE TELNET 91 ENABLE TRUSTED HOST 92 ENA

Index 224 S SAVE EBIPA 62 SAVE EBIPA6 63 SAVE VLAN 189 SEND REMOTE SUPPORT DATACOLLECTION 197 serial port 13 SET ALERTMAIL MAILBOX 95 SE

Index 225 SET VLAN REVERT 192 SET VLAN SERVER 192 SHOW ALL 56 SHOW CA CERTIFICATE 37 SHOW CONFIG 120 SHOW DATE 121 SHOW DEVICE SERIAL_NU

Index 226 U UNASSIGN 32 UNASSIGN FOR LDAP 46 UNASSIGN OA 32 UNASSIGN OA LDAP GROUP 46 UNASSIGN SERVER 167 universal time zone 208 UPDATE

Rack commands 23 SHOW RACK NAME • Command: SHOW RACK NAME • Description: Displays the user defined rack name setting for the enclosure • Access l

Rack commands 24 USE813AMMP OK No 172.16.1.60 09USE813AMMP --data error-- OA-E4115BECFBAB> SHOW TOPOLOGY IPV6 Det

User account commands 25 User account commands ADD USER • Command: ADD USER "<user name>" ["<password>"] • Descrip

User account commands 26 ASSIGN OA • Command: ASSIGN OA {"<user name>" | LDAP GROUP "<LDAP group name>"} • Descrip

User account commands 27 ENABLE STRONG PASSWORDS • Description: When enabled, this command requires that a user's password contain at least on

User account commands 28 REMOVE USER • Command: REMOVE USER {ALL | "<user name>" | CERTIFICATE "<user name>"} • De

User account commands 29 o When in FIPS Mode OFF, the character set includes all printable characters. When in FIPS Mode ON/DEBUG, the password must

Contents 3 Contents Introduction ...

User account commands 30 o You must use double quotes if the contact information contains any spaces. SET USER FULLNAME • Command: SET USER FULLNA

User account commands 31 SHOW PASSWORD SETTINGS • Description: Displays the current minimum password length and strong password settings • Access

User account commands 32 o Users who do not have OA administrator access levels can only view their user information. • Example: OA-0018FE27577F>

User account commands 33 UNASSIGN {SERVER | INTERCONNECT} {<bay number> | ALL | <bay number>-<bay number>} {"<user name>

Two-Factor Authentication commands 34 Two-Factor Authentication commands ADD CA CERTIFICATE • Command: ADD CA CERTIFICATE <end marker> <\n

Two-Factor Authentication commands 35 DISABLE TWOFACTOR • Description: Disables Two-Factor Authentication • Access level/Bay level: OA administrat

Two-Factor Authentication commands 36 When the Onboard Administrator is operating in FIPS Mode, the minimum RSA key length is 2048 bits, and the sig

Two-Factor Authentication commands 37 Failure to give a proper end marker before and after the certificate might cause the interface to wait for the

Two-Factor Authentication commands 38 • Access level/Bay level: All • Restrictions: None • Example: OA-0018FE27577F> SHOW TWOFACTOR INFO Two F

Directory commands 39 Directory commands ADD LDAP CERTIFICATE • Command: ADD LDAP CERTIFICATE <end marker> <\n> <certificate> <

Contents 4 SHOW USER ...

Directory commands 40 ASSIGN for LDAP • Command: ASSIGN {SERVER | INTERCONNECT} {<bay number> | ALL | <bay number>-<bay number>}

Directory commands 41 DOWNLOAD LDAP CERTIFICATE • Command: DOWNLOAD LDAP CERTIFICATE "<url>" • Description: o Downloads an LDAP c

Directory commands 42 o This command revokes trust in the LDAP server associated with the certificate. • Access level/Bay level: OA administrator •

Directory commands 43 o Must be 0 to 58 characters in length. o Valid characters are all alphanumeric, the underscore (_), the dash (-), and spaces

Directory commands 44 SET LDAP SEARCH {1-6 } "<search content>" • Description: Sets up to six search contexts in priority order •

Directory commands 45 M1owKTEnMCUGA1UEAxMeY2NlZ2NhbTAxLmFtZXJpY2FzLmhwcWNvcnAubmV0MIGf MA0GCSqGSIb3DQEBAQUAA4GNADCBiQKBgQDNYsB8T6rJhJQXbKvM5JLi6EXNA

Directory commands 46 Search Context #4 : Search Context #5 : Search Context #6 : TEST LDAP • Comm

HP SIM commands 47 HP SIM commands ADD HPSIM CERTIFICATE • Command: ADD HPSIM CERTIFICATE <end marker> <\n> <certificate> <\n&

HP SIM commands 48 OA administrator • Restrictions: o Do not include the network prefix length with IPv6 addresses. o When the Onboard Administra

HP SIM commands 49 The data includes the current HP SIM SSO Trust Mode (see SET HPSIM TRUST MODE) and a list of names that the Onboard Administrator

Contents 5 GENERATE KEY ...

General management commands 50 General management commands DISABLE URB • Command: DISABLE URB • Description: Disables URB reporting. • Access lev

General management commands 51 ENABLE URB • Command: ENABLE URB { HTTP | SMTP | BOTH } • Description: Enables URB reporting • Access level/Bay le

General management commands 52 — Email Address — Surname — Given Name — Alternative Name — Initials — DN Qualifier — Challenge Password — Un

General management commands 53 Prompt Description Restrictions where the Onboard Administrator is located. Organizational Unit The unit within the

General management commands 54 OA administrator • Restrictions: o The SHA-224 hash algorithm may not work with some web browsers without the lates

General management commands 55 SET FACTORY • Command: SET FACTORY • Description: o Restores the Onboard Administrator to its factory defaults. Th

General management commands 56 SET URB PROXY URL { <url> } sets the proxy URL to use when sending URB messages. SET URB INTERVAL { HOURLY <

General management commands 57 >SHOW ENCLOSURE POWER_SUMMARY >SHOW ENCLOSURE STATUS >SHOW ENCLOSURE TEMP >SHOW FIPS MODE

General management commands 58 >SHOW VLAN >SHOW URB >SHOW FIRMWARE SUMMARY >SHOW FIRMWARE

General management commands 59 URB Proxy URL: URB Interval: Daily at hour 0 Last Attempt: None TEST URB • Command: TEST URB • Description: Manu

Contents 6 DISABLE TELNET ...

Enclosure Bay IP Addressing commands 60 Enclosure Bay IP Addressing commands ADD EBIPA • Command: ADD EBIPA {SERVER | INTERCONNECT} DNS <ip addr

Enclosure Bay IP Addressing commands 61 • Description: Disables the ability of the Onboard Administrator to give devices in the bays IPv6 addresses

Enclosure Bay IP Addressing commands 62 • Access level/Bay level: OA administrator, OA operator • Restrictions: Before using this command, you mus

Enclosure Bay IP Addressing commands 63 • Access level/Bay level: OA administrator, OA operator • Restrictions: If SCRIPT MODE is ON when EBIPA is

Enclosure Bay IP Addressing commands 64 OA administrator, OA operator • Restrictions: o The <IP address> and <netmask> must be in the

Enclosure Bay IP Addressing commands 65 o The <IP address> and <netmask> must be in the form ###.###.###.###, where each ### ranges from

Enclosure Bay IP Addressing commands 66 o The /prefix length ranges from 0 to 128. The prefix length is mandatory except when specifying the gateway

Enclosure Bay IP Addressing commands 67 SET EBIPAV6 SERVER NONE 3 • Access level/Bay level: OA administrator, OA operator • Restrictions: o The &

Enclosure Bay IP Addressing commands 68 Successfully set device (iLO) bay #5B to IPv6 address 4001::4bd0/64 Successfully set device (iLO) bay #6B to

Enclosure Bay IP Addressing commands 69 172.16.0.2

Contents 7 SHOW SSHFINGERPRINT ...

Enclosure Bay IP Addressing commands 70 8 Yes 172.16.211.118 255.255.0.0 172.16.0.1 172.16.0.1 test.com

Enclosure Bay IP Addressing commands 71 Bay: 1B Enabled: No EBIPA: (Not Set) Current: (Not Set) Gateway: (Not Set)

Enclosure Bay IP Addressing commands 72 DNS 2: (Not Set) DNS 3: (Not Set) Domain: (Not Set) ---------------------

Enclosure Bay IP Addressing commands 73 EBIPA: 1000::500:10:6/64 Current: (Not Set) Gateway: (Not Set) DNS

Enclosure Bay IP Addressing commands 74 DNS 3: (Not Set) Domain: bladeslab.com ----------------------------------------------

Enclosure network configuration commands 75 Enclosure network configuration commands ADD OA ADDRESS IPV6 • Command: ADD OA ADDRESS IPV6 [{<bay n

Enclosure network configuration commands 76 The <ip address> must be in the form ###.###.###.###, where each ### ranges from 0 to 255. ADD OA

Enclosure network configuration commands 77 OA administrator • Restrictions: o SSHKEY is only available for the Administrator local account. o SS

Enclosure network configuration commands 78 o The <host> value can be an IPv4 address, an IPv6 address, or a DNS name (maximum of 64 character

Enclosure network configuration commands 79 Name Description Privacy passphrase Privacy passphrase used to encrypt operations. This entry must be a

Contents 8 SHOW SYSLOG OA ...

Enclosure network configuration commands 80 CLEAR LOGIN_BANNER_TEXT • Command: CLEAR LOGIN_BANNER_TEXT • Description: Clears the currently config

Enclosure network configuration commands 81 OA Administrator OA Bays • Restrictions: o All servers in the enclosure should be powered off before c

Enclosure network configuration commands 82 OA administrator, OA operator • Restrictions: None DISABLE ENCLOSURE_IP_MODE • Command: DISABLE ENCLO

Enclosure network configuration commands 83 OA administrator, OA operator • Restrictions: None DISABLE IPV6 • Command: DISABLE IPV6 • Descriptio

Enclosure network configuration commands 84 • Restrictions: None DISABLE NTP • Command: DISABLE NTP • Description: Disables the synchronizing

Enclosure network configuration commands 85 None DISABLE SNMP • Command: DISABLE SNMP • Description: Disables SNMP support for the Onboard Admini

Enclosure network configuration commands 86 DISABLE XMLREPLY • Command: DISABLE XMLREPLY • Description: Disables XML reply data return over the HT

Enclosure network configuration commands 87 o If your FTP server does not support anonymous connections, you can specify a user name and password in

Enclosure network configuration commands 88 ENABLE ENCLOSURE_ILO_FEDERATION_SUPPORT • Description: Enables the Onboard Administrator support requir

Enclosure network configuration commands 89 • Access level/Bay level: OA administrator, OA operator • Restrictions: o An IPv4 DNS server must be

Contents 9 ASSIGN INTERCONNECT ...

Enclosure network configuration commands 90 • Access level /Bay level: OA administrator • Restrictions: None ENABLE IPV6 • Command: ENABLE IPV6

Enclosure network configuration commands 91 ENABLE SLAAC • Command: ENABLE SLAAC • Description: Enables auto-configuration of IPv6 addresses from

Enclosure network configuration commands 92 ENABLE TRUSTED HOST • Command: ENABLE TRUSTED HOST • Description: Enables IP security for the Onboard

Enclosure network configuration commands 93 REMOVE OA DNS • Command: REMOVE OA DNS [<OA bay number>] <ip address> • Description: Remov

Enclosure network configuration commands 94 • Access level/Bay level: OA administrator, OA operator • Restrictions: IPv6 addresses cannot specify

Enclosure network configuration commands 95 Removes an IPv4 or IPv6 address from the list of addresses being handled by the IP Security feature. •

Enclosure network configuration commands 96 SET ALERTMAIL SENDERNAME • Command: SET ALERTMAIL SENDERNAME "<name>" • Description: S

Enclosure network configuration commands 97 o If the change is to FIPS MODE ON or FIPS MODE DEBUG, strong passwords are enabled, minimum password le

Enclosure network configuration commands 98 SET LOGIN_BANNER_TEXT <end marker> <\n> <banner text> <\n> <end marker> •

Enclosure network configuration commands 99 • Description: Sets the primary server used for synchronizing time and date using the NTP. The <host