Hp EML E-series Tape Libraries Bedienungsanleitung Seite 1

HP StorageWorksEnterprise Modular Library E-Seriesuser guideAH876-96001Part number: AH876-96001Fourth edition: September 2007

10

Preparing the library for long-distance relocation1. Use your application software to remove all tape cartridges from the tape drives.2. Remove all ta

c. Roll the library onto the p allet.2. Secure the library:a. Place the antistatic ba g over the library, and secure it into place.b. Use the four shi

102Moving the library

ASpecifications an d characteristi csThis appendix describes the physical, electrical, and environmental characteristics of the library.Library compone

CharacteristicSpecificationPower rating297 V AInput current1.5 A (at 200 VAC)Capacit y expansion modu le (8U)Physical:Weight 20.1 kg (44.2 lb)Dimension

Library environmental specificationsTable 30 Libraryenvironmentalspecifica tionsMeasurementsItemOperating Storage TransportingTemperature+10 to +35ºCnl(

106Specifications and characteristics

B Regulatory comp lian ce noticesThis appendix contains regulatory notices for the library.Regulatory compliance identification numbersFor the purpose

Dutch battery noticeWAARSCHUWING: dit apparaat bevat mogelijk een batterij. - Probeer de batterijen na het verwijderen niet op te laden. - Stel de ba

German bat tery noticeVORSICHT: Dieses Produkt enthält unter Umständen eine Batterie oder einen Akku.- Versuchen Sie nicht, Batterien und Akkus außer

About this guideThis guide provides information to help you o perate the library, troubleshoot problems, a nd remove andreplace customer self-repair c

Japanese batterynoticeSpanish bat ter y noticeADVERTENCIA: Este dispositivo podría contener una batería.- No intente recargar las baterías si las ext

reasonably b e expected to be installed in a residential environment (for example, personal computers).The FCC requires devices in both classes to b e

Canadian notice(Avis Canadien)Class A equipmentThis Class A digital apparatus meets all requirements of the Canadian Interference-Causing EquipmentReg

Japanese power cord statementKorean noticesClass A equipmentClass B equipmentTaiwanese noticesBSMI Class A noticeEnterprise Modular Library E-Series11

Taiwan batter y recycle statementRecovery mark:Four-in-one recycling symbolRecovery text:“Please recycle waste ba tteries”廢電池請回收Laser complianceThis d

French laser noticeAVERTISSEMENT : cet appareil peut être équipé d'un laser classé en tant que Produit laser de classe 1 et conforme à la réglem

Japanese laser noticeSpanish laser noticeADVERTENCIA: Este dispositivo podría contener un láser clasificado como producto de láser de Clase 1 de acue

Czecholslovakian noticeDanish noticeBortskaffelseafaffaldfrahusstandeidenEuropæiskeUnionHvis produktet eller dets emballage er forsynet med dette symb

Estonian noticeFinnish noticeLaitteiden hävittäminen kotitalouksissa Euroopan unionin alueellaJos tuotteessa tai sen pakkauksessa on tämä merkki, tuot

Greek noticeHungarian noticeItalian noticeSmaltimento delle apparecchiature da parte di privati nel territorio dell'Unione EuropeaQuesto simbolo

CAUTION:Indicates that failure to follow directions could result in damage to equipm ent or data.IMPORTANT:Provides clarifying information or specific

Latvian noticeLithuanian noticePolish notice120Regulatory compliance notices

Portuguese noticeDescarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve se

Swedish noticeBortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller f

C Ordering HP tape cartrid ges an dbar code la b el packsWhere to buy tape cartridges and bar code labelsHP recommends using HP tape cartridges in you

Part numbers fortape cartridges and bar code labelsTable 33 HP tape cartridges and bar code labelsTape drive type/productHP part numberUltrium 460Data

D I nstalling a redundant PDUPDU componentsThe library comes with one PDU installed. For a variety of reasons, it m ay be desirable or necessarytoadda

supplies in the library that are allowed by the leakage current specification. You must check the powerratings of any additional equipment added to the

1053513421Power strip #2 3Power strip #42Redundant PDU (#2)4Caster bossFigure 58 Redundant PDU and power strip placementInstallation of redundant PDU

128Installing a redundant PDU

Glossaryarray (1) A section of vertical or horizontal tape car tridge receptacles inside a library.(2) A molded unit that holds multiple cartridges.ba

NOTE:In environments with high potential for static electricity, take additional precautions, such as the use of anantistatic smock or a grounded anti

drive module The entire assembly tha t houses the tape drive, including the metal housingand connectors.ESD Electrostatic discharge. The release of st

lift drive assembly A component of the robot that moves the table assembly vertically among thelibrary mod ules.lift drive pulley A component of the l

table assembly A component of the robotics unit that carries the picker assembly verticallyamong the library modules.tape cartridge A container holdin

In dexSymbols71econfiguration,17number of slots,20reserved slots,32,52slot numbering,33upgrading,23,38, 55, 56, 57, 58, 58, 61, 62, 63, 64Aadapter pane

EMLnetwork,28physical description,17powering off,40powering on,39repacking,100European Union notice,112Event Log Type Selection screen,50expansion mod

LTO4bar code label,41LEDs,60part number,94removal and replacement,94Mmagazinedepiction,29functional description, 21, 29inserting cartridges,43insertin

Status screen,48Subscriber’s Choice, HP,14Support screen,54support ticket,69switchLEDs,60ports,30symbols in text,11Ttable assembly,21Ta iwanese notice

• Clean the connector before making a connection. Make sure that there are no obstructionsand that keyways are aligned.Fiber-optic cable handlingObser

To make comments and suggestions about product documentation, please send a message [email protected]. All submissions become the property

16About this guide

1LibraryoverviewThe HP StorageWorks Enterprise Modular Library (EML) E-Series Tape Libraries provide per formance,reliability and investment protectio

ConfigurationIllustra-tionHeightin “U”MaximumslotsavailableConfig-urable loadport slots(in multiplesof 5)Config-urable re-served slotsNumberofpossibletap

1096712335467778910111077777777711111Reserved space. If your librarycontains LTO4 tape drives, thisspace contains the switch for theinternal network.7

Legal and notice information© Copyright 2005-2007 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change witho

109687103999944651112121212111413138121010101Reserved space8Base modu le card cage (e2400-FC2Gb interface controller shown)2Switchfor the internal net

limits the distance that the robot can travel. If the library floor is attached to the base module, the bot tomtwo rows (containing 16 slots) cannot be

•Library robotics c ontroller (see Figure 8 on page 25)—A single slot, 6U-wide cPCI boa rd havingEthernet ports and an RS-232 port. One Ethernet port

IMPORTANT:If you are adding expansion modules to an EML 71e, you must purchase a capacity upgrade licenseforCommandViewTL(partnumberAH063A).Thislicens

library tape drive capacity. One interface controller is added for every four additional LTO2 or LTO3tape drives. LTO4 tape drives do not connect to a

1097832 11Viewing windows3Cable management features210-Cartridge load portFigure 7 Capacit y expansion moduleController cardsThis section explains th

Command View TL software, provides remote management of the library by using a serial, Telnet, orWeb-based graphical user interface (GUI).104211 3 4 5

104223 41 21FC por ts to LTO2 and LTO3 tapedrives3Ethernet port (connection to InterfaceManager c ard)2FC ports to hosts4Serial por tFigure 10 Ports o

Functional descriptionThe library receives commands and data throughout the SAN from hosts running applications fromapproved independent software vend

Load ports and magazinesThe load ports are mechanical d evices on the front of the library that enable you to import and exporttape cartridges to and

ContentsAboutthisguide ... 11Intendedaudience... 11Relateddocumentation...

Tabl e 3 Ultrium compatibilityTape drive200 GB1400 GB1800 GB1WORM 800GB11600 GB1WORM1600 GB1Ultrium 460(LTO2)Read/writeOptimumNotsupportedNotsupported

Operator control panelThe OCP displays library status information and allows you to access the library menus with a touchscreen. Use these menus to vi

• In general, the library numbers the slots one module at a time, starting with the top module.For slot numbering purposes, the 12U base module is con

1043912349567112345678923456789121286781912101152341Robot park zone7Row numbering2Array targets for the bar code scanner8Column numbering3Slots availa

1043912349567112345611789234562345678923456121288 9101111412137236541Robot park zone8Expansion identification label2Arraytargetsforthebarcodescanner9Ro

104401234956781354 6 798212345678910111212345678910111212341Slots available for data cartridges6Expansion identification label2Array targets7Row number

10979123456781234561234561234561Slots available for data cartridges4Expansion identification label2Array targets5Row numbering3Slots unavailable for us

10956123410 11956781734 5261234567891011121234567891011121Slots available for data cartridges5Row numbering2Array targets6Column numbering3Slots unava

IMPORTANT:If you are upgrading an EM L 71e, you must purchase a capacity upgrade license for Command View TL(part number AH063A). This license upgrade

2 Using the libraryThis chapter describes operating procedures for the library.Powering on thelibrary1. Close the center door of the library and turn

OCPtabsandstatusbar ... 45Timeouts... 46OCPfunctions...

1044511Library main power switchFigure 23 Library main power switch controlNOTE:The following step applies only when the library is powered on for the

Center-door interlockThe center door on the front of the library cannot be opened until a password-protected command tounlock the c enter door is sele

CAUTION:The misuse and misunderstanding of bar code technology can result in backup and restore failures.To ensure that your b ar codes meet HP’s qual

116570 0 0 2 2 0 L30 0 0 2 2 0 L4Figure 25 Attac h ing an Ul t rium bar code lab

CAUTION:Guard plates prevent acc ess to the inside of the library when a load port magazine isremoved. These doors will move back out of the way when

Table 4 OCP iconsIconDescriptionCritical error—A comp onent failure h as made the library inoperable.Warning—A component failure has degraded library

Figure 29 Menu screenThe status bar is a quick indicator of library health. The bar is green when the library is functioningnormally, yellow during a

• If an error condition occurs while the library is timed-out, the backlight comes on for 60 minutes.If the OCP is touched during this 60-minute perio

Home ScreenStatus ScreenSupport ScreenIdentity ScreenHP Support InfoUnlock Load PortsUnlock DoorReboot LibraryMedia OperationsRun Admin TestsService M

Figure 31 OCP Sta tus screenEnterprise Modular Library E-Series49

Removingapowersupplyfromthecardcageexpansionmodule... 91Replacingapowersupplyinthecardcageexpansionmodule... 92LTO2orLTO3tape

Table 5 Status sc reen functionsFunction DescriptionIdentity ScreenContains basic configuration information. The library name and IPaddress is obtained

Figure 32 OCP Co nfiguration screenEnterprise Modular Library E-Series51

Table 6 Configura tion sc reen functionsFunction DescriptionLibrary ConfigurationAllows the following items to be configured:• Change Password—The librar

Figure 33 OCP Opera tions screenTable 7 Operations screen functionsFunction DescriptionUnlock Load PortsInstructs the robot to unlock all lo ad port d

Function DescriptionMedia OperationsPerforms the following tasks:• Move tape—Select a Source and Element Type (where you want tomove a tape from)andaD

Figure 34 O CP Support screenTable 8 Support screen functionsFunction DescriptionHP SupportInfoProvides alternate locations where useful information c

104701 2 3 4Figure 35 Indicators on the library robotics controllerTable 9 Ind i cators on the librar y robotics controllerIndexNo.Control/indicatorFu

109821 42 3Figure 36 Indicators and rese t on the Interface Manager cardTable 10 Indicators and reset on the Interface Manager cardIndexNo.Control/ind

gl010111 2Figure 37 Indica tors on t h e e2400-FC 2Gb interfac e controll erTable 11 Indicators on the e2400 -FC 2Gb interface controllerIndexNo.Contr

Figure39IndicatoronanLTO2orLTO3tapedriveTable 13 Indicator on an LTO2 or LTO3 ta pe driveIndexNo.Control/indicatorFunction1FAULT LEDWhen lit (yellow),

Germanlasernotice... 115Italianlasernotice... 115Japaneselasernotice ...

11667FAULT12 3 4Figure 40 Indicators o n an LTO4 tape driveTable 14 Indicators on an LTO4 tape driveIndexNo.Control/indicatorFunction1FAULT LEDWhen li

115941 2234Figure 41 Indicators on the switch for the interna l networkTable 15 Indicators on the switch for the internal networkIndexNo.Control/indic

104451Figure 42 Control on the library main power switchTable 16 Control o n th e libra ry main power switchIndexNo.Control/indicatorFunction1SwitchWh

Figure 43 Indicator on the autoranging power supplyTable 17 In di cator on the autoranging power supp lyIndexNo.IndicatorFunction1PowerLEDWhenlit(gree

Figure 44 Indicators on the card cage expansion module power supplyTable 18 Indicators on t he card cage expansion module power supplyIndexNo.Control/

104512101101 2 34Figure 45 Controls and indica tor on the PDUTable 19 Controls and indicator on t he PDUIndexNo.Control/indicatorFunction1PowerLEDWhen

66Using the library

3 Maintaining the lib raryThis chapter describes routine maintenance and solutions to problems you might encounter whileoperating the library.Periodic

CAUTION:Only use H P Ultrium universal cleaning cartridges in HP Ultrium tape drives. See Appendix C forobtaining supplies. The sa me cleaning car tri

reserved slots, or type of tape drive (LTO2, LTO 3, or LTO4), might require changes to software. Someapplication software may require the purchase of

Figures1Frontviewofthelibrary ... 192Rear view of thelibrary ... 203Roboticsunit...

ProblemCorrective actionThe library or tape drives arenot d etected by the InterfaceManager card or Command ViewTL software.• Check cable connections.

OCP p roblemsTable 22 OCP problemsProblemCorrective actionThe OCP is blank.• Touch the OCP to wake i t from sleep m ode.• Confirm tha t the power is on

Robotics problemsTable 23 Robotics problemsProblemCorrective actionTherobotdoesnotmoveatpoweron.• Make sure that all internal shipping restraints have

Operating problemsTable 24 Operating problemsProblemCorrective actionThe host computer cannotcommunicate with the library.• Make sure that Command Vie

Table 25 Tape drive problemsProblemCorrective actionThe library is unable tocommunicate with a tape drive.This is indicated by a Drive Communication T

SymptomPossibl e cause SolutionCommand View TL serverdoes not detect theInterface Manager card(cont.).Incorrect IP addressMake sure that the correct I

SymptomPossible cause SolutionSystem interferenceRetry the command. This behavior can be expected ifsystem activity is high, because the Interface Man

Table 27 Inte rface Manager card LED fault isolationIndicators ProceduresRed LEDGreen LEDBlinks 1x per 5second intervalOffBlinks 2x per 5second interv

Each of these topics is discussed in the following sections.Examining FC port connectionMost hubs and switches have link indicators showing link statu

Table 28 Terminal configuration settingsAttributeSettingBAUD RateAutobaud, 9600,19200,38400,57600,115200Data Bits8Stop Bit1ParityNoneFlow ControlNone o

35Indicatorsonthelibraryroboticscontroller... 5636IndicatorsandresetontheInterfaceManagercard ... 5737Indicatorsonthee

80Maintaining the library

4RemovingandreplacingpartsThis chapter provides information for the removal and replacement of each expansion module andfield replaceable unit (FRU).CA

10482Figure 46 Removing the library robotics controllerReplacing the library robotics controller1.Orient the library robotics controller as shown in F

HP StorageWorksInterface Manager cardPart Number342213-001 or 393531 -001LocationBottom slot in the base-module card cageCharacteristicsContains six E

10483Figure 47 Removing the Interface Manager card9. Move the CompactFlash memory card from the original Interface Manager c ard to the new InterfaceM

3. Tighten the captive screws in both ejector handles. Use a #1 Phillips screwdriver.4. Plug the cables into the Interface Manager card exactly as the

• The power LED is on and the ACT/LNK LEDs are off instead of g reen (see“HP StorageWorks e2400- F C 2Gb interface controller” on page 57) .•ThepowerL

5. When you install a new interface controller, you must use a different power-on procedure one time:a. Turn on the power to the library.b. Wait appro

4. Label the cables or write a note that shows the locations of all the cables plugged into the inter facecontroller to make it easier to reconnect th

IMPORTANT:If you do not allow sufficient time for the interface controller to reset before resetting it again, theInterface Manager card will not recog

Tables1 Documentconventions... 112EML configu rations ... 173Ultriumcompatibility ...

10466Figure 51 Screw locations on the base-module power supplyWARNING!The power supply might be hot.5. Pull the handle on the power supply to remove i

4. Plug the power cord into the power supply.5. If the power to the library was previously turned off, turn on the power to the library.Power supply i

Figure 53 Removing a pow er supply from a card cage expansion moduleReplacing a power supply in the card cage expansion module1.Orient thepower supply

CAUTION:To avoid damaging FC cables, do not pinch or sharply bend the cables tighter than a5-cm (2-inches) diameter.2. Unplug the FC cable from the ta

10517Figure55ConnectingtheFCcabletoatapedriveNOTE:Replacement tape drives placed i nto previously occupied drive bays are recognized by thelibrary. Ta

Removing an LTO4 tape drive1. Unload any tapecartridges from the tape drive to be removed using your application software or thelibrary operator contr

115512. Remove the end cap from the FC port A connector on the new tape drive.CAUTION:To avoid damaging FC cables, do not pinch or bend the cables sha

11558266. Close the back doors of the library.7. Make sure that the tape drive has the latest firmware for correct operation. If necessary, upgrade the

CAUTION:Guard plates prevent acc ess to the inside of the library when a load port magazine isremoved. These doors will move back out of the way when

5 Moving the libraryThis section explains how to move or ship the library. To s hip the library, or move it using a motorvehicle(forexample,truck,orfo