Hp Linux Server Management Software Bedienungsanleitung Seite 49
- Seite / 72
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Toolkit utilities 49
LogicalDrive
The value that you enter for this option specifies the ID number of the logical drive that is to be created or
modified. The first logical drive on an array must have an ID of 1 (not 0), and logical drive numbering must
be contiguous.
• In Configure action mode, ACU accepts only the ID number of the next possible logical drive.
• In Reconfigure action mode, ACU also accepts the ID number of any existing logical drive.
LogicalDriveSSPState
This option is valid only for controllers that enable SSP on a logical drive basis. Other controllers that support
SSP use the SSPState option ("SSPState" on page 46).
The following defaults apply:
• For new logical drives, the default value is Disabled.
• For existing logical drives, the default value is the current logical drive setting.
ParityGroups
When you create a RAID 50 or RAID 60 configuration, you must also set the number of parity groups.
You can use any integer value greater than 1 for this setting, with the restriction that the total number of
physical drives in the array must be exactly divisible by the number of parity groups.
The maximum number of parity groups possible for a particular number of physical drives is the total number
of drives divided by the minimum number of drives necessary for that RAID level (three for RAID 50, four for
RAID 60).
PreferredPath
If you select the Manual setting for PreferredPathMode (on page 45), use the PreferredPath
command to specify the path for I/O to the logical drive on a redundant controller in active/active mode.
The default setting for this option is 1. With this setting, the controller in chassis slot 1 is the preferred
controller for I/O to the logical drive. If you select 2, the controller in chassis slot 2 becomes the preferred
controller for the logical drive.
To determine the chassis slot numbers, use the show command on a controller that supports redundant
controllers.
RAID
The value that you enter for this option specifies the RAID level of the logical drive.
• When the Action mode is Configure, and the Method mode is Auto, ACU automatically selects the
highest RAID level that the controller and drive configuration can support except RAID 50 or RAID 60.
To specify RAID 50 or 60 for a controller that supports either of these RAID levels, use the Custom
setting. In this case, you must also specify the number of parity groups ("ParityGroups" on page 49).
• When the Action mode is Reconfigure, the default value is the existing RAID level for that logical drive.
If you specify a different RAID setting, then ACU either ignores the new setting (when Method mode is
Auto), or attempts to migrate the logical drive to the specified RAID level (when Method mode is
Custom).
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Introduction 6
- Windows Server® 2008 R2) 7
- Deployment overview 8
- Sample deployment procedure 8
- Creating a network share 9
- Advanced topics 13
- • STARTDEPLOY.CMD 14
- • SERVERDETECT.CMD 14
- • DEPLOYSERVER.CMD 14
- • UNATTEND.TXT 14
- Advanced topics 15 15
- Advanced topics 16 16
- Advanced topics 17 17
- Advanced topics 18 18
- Advanced topics 19 19
- Advanced topics 20 20
- Advanced topics 21 21
- Advanced topics 22 22
- • Verify the error level 23
- Erasing array configurations 24
- Toolkit utilities 25
- Using toolkit utilities 26
- Using REBOOT 26
- Using SETBOOTORDER 27
- Using STATEMGR 28
- Using RBSURESET 29
- Using BOOTEXTRACT 29
- Using HPDISCOVERY 30
- Using IFHW 31
- IFHW return codes 32
- IFHW command line examples 32
- Expression examples 32
- Using HWQUERY 33
- Using CONREP 34
- CONREP command-line syntax 35
- CONREP return codes 35
- CONREP screen output 35
- 100-series servers 36
- Toolkit utilities 37 37
- CONREP command file contents 38
- Using HPACUSCRIPTING 39
- Using an Input script 40
- Creating an ACU script file 40
- Toolkit utilities 41 41
- Script file options 42
- Control category 43
- Controller category 44
- Toolkit utilities 45 45
- SSPState 46
- SurfaceScanDelay 46
- Video performance options 46
- Array category 47
- Logical Drive category 48
- Toolkit utilities 49 49
- Toolkit utilities 50 50
- HBA category 51
- ACU scripting error messages 52
- Using HPLPCFG 55
- HPLPCFG return codes 56
- Using HPONCFG 57
- HPONCFG return codes 58
- Toolkit utilities 59 59
- Using HPQLAREP 60
- HPQLAREP return codes 61
- Using LO100CFG 62
- Troubleshooting 64
- Technical support 65
- Acronyms and abbreviations 66
- Index 70 70
- Index 71 71
- Index 72 72
Verwandte Produkte und Handbücher für Software Hp Linux Server Management Software
Software Hp Access Control Bedienungsanleitung
(22 Seiten)
(22 Seiten)
(37 Seiten)
(120 Seiten)Whirlpool R 24 S (EU) podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Lodówki Whirlpool R 24 S (EU).
Dostarczamy 1 pdf podręczników Whirlpool R 24 S (EU) do pobrania za darmo według typów dokumentów: Instrukcja Obsługi
Kommentare zu diesen Handbüchern