HP Integrity NonStop Release and Migration Bedienungsanleitung Seite 125
- Seite / 320
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Updating Service Processor (SP) Firmware
G06.24 Software Installation and Upgrade Guide—528593-005
7-5
Verify That Your Current RVU Is Running the Correct
Version of SP Firmware (Using TSM)
Verify That Your Current RVU Is Running the Correct Version of
SP Firmware (Using TSM)
1. Log on to the TSM Service Application.
2. Select Display>SP Actions.
The Service Processor Actions dialog box appears. Wait for the firmware version of
each SP to appear (this might take several minutes).
3. Verify that the correct version of SP firmware for your current RVU is displayed for
each SP.
If any SP has a different version of SP firmware, update that SP to the correct
version for your current RVU:
a. Select Display>Firmware Update to update the SP firmware to the proper
version for your current RVU.
b. Monitor the status of the firmware update by using the Firmware Update Action
Summary:
•
If the firmware update finishes successfully, reset the SP, as described
under Resetting an SP Using the TSM Low-Level Link on page 7-18.
•
If the firmware update fails, you might have a faulty SP or a down-rev
customer-replaceable unit (CRU). Contact your service provider.
If Necessary, Reset the SPs Prior to Updating the SP Firmware
After verifying that the SPs are running the correct version of SP firmware for your
current RVU, and before you begin to update firmware, you might have to reset all SPs
in both ServerNet fabrics (X and Y). Failure to do so could result in the loss of critical
system resources. Each SP takes about two minutes to reset.
1. If necessary, log on to the TSM Service Application.
2. From the toolbar, select SP Actions, or select Display> SP Actions to display the
Service Processor Actions dialog box.
3. Click Select all Y Fabric SPs.
4. From the Available Actions list, select Reset and then click Perform action.
5. Click OK in response to this message:
This action takes up to 2 minutes for the SP to complete the reset even if the action
appears to complete immediately.
This action will cause any current Firmware Update actions against this SP to abort.
Verify there are no Firmware Updates being performed on this SP before continuing.
Are you sure you want to reset this SP?
WARNING. To avoid hardware damage, never reset an SP if the firmware update does not
finish successfully.
- G06.24 Software 1
- Installation and 1
- Upgrade Guide 1
- Document History 2
- Part I. Upgrade Tasks 5
- 5. Installing the G06.24 RVU 6
- 9. Updating SCSI Boot Code 7
- 10. Running ZPHIRNM 7
- 11. Loading the G06.24 RVU 8
- Contents 10
- Versions (continued) 10
- Glossary 12
- What’s New in This Manual 15
- New and Changed Information 16
- About This Manual 17
- Notation Conventions 19
- General Syntax Notation 20
- Notation for Messages 21
- Overview of Installing G06.24 23
- TSM Client Applications 24
- OSM Client-Based Components 24
- DSM/SCM and the G06.24 RVU 27
- Updating Firmware 29
- ServerNet Adapter Firmware 29
- SPRs on page 3-8 30
- G06.24 31
- Concentrators 33
- Investigating a New RVU 35
- Installing a New RVU 35
- Components 38
- Notes on the FALLBACK Macro 40
- Notes on the CLEANOSS Macro 40
- Using ZPHIRNM 41
- NonStop TCP/IP FTP (G06.08) 42
- Products 43
- 4619 Disk Drives 44
- C++ (G06.20) 45
- DP2 (G06.16, G06.23, G06.24) 46
- OSS (G06.12 through G06.24) 48
- DSM/SCM (T6031D46) Fallback 49
- NonStop SQL/MP 50
- Installing SQL/MX Release 2.0 53
- (G06.08 through G06.24) 54
- Checking Current Version 55
- CSPOOL Set at HIGHPIN 56
- SWID (T9298D40^AAK) (G06.20) 57
- TMF (G06.23 and G06.24) 60
- TMF Fallback from G06.24 61
- Visual Inspect (G06.20) 62
- 2 G06.24 Upgrade Checklists 67
- G06.24 Upgrade Checklists 68
- G06.24 Upgrade Checklist 68
- D46 SPR of DSM/SCM 73
- Fallback SPRs 76
- Interoperability SPRs 77
- VST937.vsd 79
- Verify System Operations 83
- VST200.vsd 85
- Check Disk Subsystem Status 90
- Check the Tape Drive Status 93
- Record the Current SYSnn 94
- Back Up Important Files 94
- 5 Installing the G06.24 RVU 95
- Installing the G06.24 RVU 100
- Interface (ZPHITI) 113
- (ZPHITI) 114
- Microcode (Pre-G06.06) 119
- Replacing the Disk Bootstrap 119
- Firmware 121
- Before You Begin 123
- SP Firmware (Using TSM) 125
- Application 128
- VST647.vsd 131
- VST680.vsd 134
- (Using TSM) 135
- (SPs) list 139
- 9. Click Close 139
- Connection 140
- VST939.vsd 141
- VST949.vsd 142
- VST966.vsd 143
- Connection) 148
- System Console (Optional) 148
- (Optional) 150
- Updating Processor Boot Code 151
- Check Processor Status 153
- CPUCODE9 156
- VST955vsd 159
- Reset or Equivalent 160
- Code (Both for OSM and TSM) 166
- Updating SCSI Boot Code 169
- (Pre-G06.08 RVU) 169
- Necessary) 170
- 10 Running ZPHIRNM 173
- Subvolume 174
- Stop All Applications 175
- Drain the Spooler 175
- Using ZPHIRNM PREVIEW Mode 176
- Steps for Running ZPHIRNM 177
- Running ZPHIRNM 179
- 11 Loading the G06.24 RVU 181
- Halt the Processors 182
- Loading the G06.24 RVU 183
- Low-Level Link 184
- The Reset Operation 188
- 12 Resuming Normal Operations 189
- Resuming Normal Operations 190
- Complete 191
- (Overview) 194
- Configure the Spooler 197
- Before Starting DSM/SCM 198
- Initialize SQL 198
- Configure OSS 201
- Configure SMF (Optional) 202
- Part II. Fallback Tasks 205
- 13 Preparing to Fall Back 207
- Summary of Fallback Tasks 208
- DLL (Dynamic-Link Libraries) 209
- Open System Services (OSS) 210
- OSM and TSM 210
- SQL/MX 2.0 211
- WAN Manager (T8365) 211
- Preparing to Fall Back 212
- 4> TMFCOM START TMF 213
- 6> RUN STARTSCM 213
- Submit a Backout Request 215
- Monitor the Backout Process 219
- Versions 221
- Version (Using TSM) 222
- Version (Using OSM) 225
- Previous Software Revision 229
- Run ZPHIRNM 230
- Software Revision 231
- Loading the Previous RVU and 233
- Prepare to Stop the System 234
- SYSnn and CONFxxyy 235
- Resume Normal Operations 236
- Configure Spooler 237
- Operations 238
- Using DSM/SCM to Install SPRs 239
- Install SPRs With DSM/SCM 240
- Determine the Current SYSnn 241
- Build the New Revision 243
- If a System Load Is Required 247
- Perform a System Load 248
- Client SPRs 251
- Software 252
- Identification (SWID) SPR 253
- 8. Click OK 258
- D46 SPR and SWID 260
- Revision 261
- Restart Applications 265
- Verify That SWID Is Installed 267
- D46 Version of DSM/SCM 268
- 4. Click Start 279
- Update Fails on page C-7 282
- Update SWAN Firmware 284
- Or (using SCF) enter: 285
- VST400.vsd 286
- Or (using SCF), enter: 289
- Verify That CLIPs Are Stopped 290
- Code File 291
- T7954Vnn^ddmmmyyyy^AAN) 292
- VST440.vsd 293
- VST960.vsd 295
- VST951.vsd 296
- VST961.vsd 297
- Glossary-2 302
- Glossary-3 303
- Glossary-4 304
- Glossary-5 305
- Glossary-6 306
- Glossary-7 307
- Glossary-8 308
- Glossary-9 309
- Glossary-10 310
- Glossary-11 311
- Glossary-12 312
- Glossary-13 313
- Glossary-14 314
- Special Characters 320
Verwandte Produkte und Handbücher für Software HP Integrity NonStop Release and Migration
Software HP 2600-PWR Bedienungsanleitung
(418 Seiten)
(418 Seiten)
Software HP 5992-3193 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
Software HP Laptop 7.2 Bedienungsanleitung
(53 Seiten)
(53 Seiten)
Software HP 1.5TB Bedienungsanleitung
(216 Seiten)
(216 Seiten)
Software HP 2/8q Bedienungsanleitung
(188 Seiten)
(188 Seiten)
Software HP T5700 Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Software HP XP512 Bedienungsanleitung
(99 Seiten)
(99 Seiten)
Software HP XP10000 Betriebsanweisung
(109 Seiten)
(109 Seiten)
Software HP NetMail/3000 Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Software HP Moonshot-45G Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Software HP T5300 Bedienungsanleitung
(338 Seiten)
(338 Seiten)
Software HP X9320 Betriebsanweisung
(150 Seiten)
(150 Seiten)
Software HP 48gII Bedienungsanleitung
(175 Seiten)
(175 Seiten)
Software HP B6191-90029 Bedienungsanleitung
(140 Seiten)
(140 Seiten)
Software HP 250m Informationsblatt
(95 Seiten)
(95 Seiten)
Software HP 5992-3838 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Software HP XP20000 Bedienungsanleitung
(170 Seiten)
(170 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern