HP ProDesk 400 G5 Base Model Small Form Factor PC Bedienungsanleitung

Hardware Reference GuideHP ProDesk 400 G5 SFF Business PC

Front panel componentsDrive conguration may vary by model. Some models have a bezel blank covering the slim optical drive bay.1 Slim optical drive (o

Rear panel components1 Audio-in jack 5 VGA monitor connector2 RJ-45 (network) jack 6 USB ports (4)3 Audio-out jack for powered audio devices7 USB Supe

2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. No tools are needed for most of the

Removing the computer access panelTo access internal components, you must remove the access panel:1. Remove/disengage any security devices that prohib

Replacing the computer access panelPlace the panel on the computer (1), slide it forward (2), and tighten the thumbscrew (3) to secure the panel in pl

Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis

Removing a slim optical drive bezel blankOn some models, there is a bezel blank covering the slim optical drive bay that needs to be removed before in

Replacing the front bezelInsert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1), and then rotate the top

Changing from desktop to tower congurationThe Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be

System board connectorsRefer to the following illustration and table to identify the system board connectors for your model.No. System Board Connector

© Copyright 2018 HP Development Company, L.P.Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/o

Upgrading system memoryThe computer comes with double data rate 4 synchronous dynamic random access memory (DDR4-SDRAM) dual inline memory modules (DI

DIMM and one 1 GB DIMM, and Channel B should be populated with the other two 1 GB DIMMs. With this conguration, 4 GB will run as dual-channel and 1 G

6. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Press the module down into the socket, ensurin

Removing or installing an expansion cardThe computer has one PCI Express x1 expansion socket and one PCI Express x16 expansion socket.NOTE: The PCI Ex

a. If you are installing an expansion card in a vacant PCI Express x1 socket, insert a at-bladed screwdriver into the slots on the rear of expansion

c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card (1) and carefully rock th

11. To install a new expansion card, hold the card just above the expansion socket on the system board and then move the card toward the rear of the c

14. Replace the computer access panel.15. Reconnect the power cord and any external devices, then turn on the computer.16. Lock any security devices t

CAUTION: To prevent loss of work and damage to the computer or drive:If you are inserting or removing a drive, shut down the operating system properly

7. Press the release lever on the back of the drive (1), and then slide the drive through the front bezel (2).Installing a 9.5 mm slim optical drive1.

Safety warning noticeWARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on

7. Align the small pin on the release latch with the small hole on the side of the drive and press the latch rmly onto the drive.8. Slide the optical

9. Connect the power cable (1) and data cable (2) to the rear of the drive.10. Connect the opposite end of the data cable to the light blue SATA conne

6. Disconnect the power cable (1) and data cable (2) from the rear of the optical drive.7. Press the release lever on the back of the drive (1), and t

8. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive.9. Press inward on the drive cage release latch (1), rotate the d

● If you are removing a 2.5-inch hard drive, remove the four screws that secure the drive to the drive cage (1) and then slide the drive out (2).11. I

● If you are installing a 2.5-inch hard drive, slide the drive into the drive cage (1) and secure the drive with four M3 metric screws (2).NOTE: The f

12. Hold the drive cage at an angle and insert the tabs on the side of the drive cage into the slots on the chassis (1), and then lower the other side

14. Slide the optical drive through the front bezel all the way into the bay (1) so that it locks in place (2).15. Connect the power cable (1) and dat

Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Security cable lockPadlock3

HP Business PC Security Lock V21. Loop the security cable around a stationary object.2. Attach the security cable fastener to a desktop using the appr

iv Safety warning notice

3. Slide the security cable through the security cable fastener.NOTE: This step is not necessary if you looped the security cable around a stationary

5. Slide the security cable through the security guide installed on the monitor.6. Attach the accessory cable fastener to a desktop using the appropri

7. Slide the security cable through the holes in the accessory cable fastener.8. Screw the lock to the chassis using the screw provided.34 Chapter 2

9. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lo

A Battery replacementThe battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equival

b. Slide the replacement battery into position, positive side up. The battery holder automatically secures the battery in the proper position.Type 2a.

b. To insert the new battery, slide one edge of the replacement battery under the lip of the holder with the positive side up (1). Push the other edge

11. Reset the date and time, your passwords, and any special system setups using Computer Setup.12. Lock any security devices that were disengaged whe

B Electrostatic dischargeA discharge of static electricity from a nger or other conductor may damage system boards or other static-sensitive devices.

C Computer operating guidelines, routine care and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properl

About This BookThis guide provides basic information for upgrading the HP ProDesk Business PC.WARNING! Indicates a hazardous situation that, if not av

Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation● Do not move the drive du

D AccessibilityHP designs, produces, and markets products and services that can be used by everyone, including people with disabilities, either on a s

IndexAaccess panelremoval 5replacement 6accessibility 43Bbattery replacement 36Ccomputer operating guidelines 41Ddrivescable connections 19installatio

vi About This Book

Table of contents1 Product features ...

Appendix C Computer operating guidelines, routine care and shipping preparation .... 41Computer operating g

1 Product featuresStandard conguration featuresFeatures may vary depending on the model. For support assistance and to learn more about the hardware