HP EliteOne 800 Betriebsanweisung

Hardware Reference GuideHP EliteOne 800 G1 All-in-One

Side componentsFigure 1-3 Side componentsTable 1-2 Side componentsComponent Component1 Hard disc drive activity LED 6 Headset/line out jack2 HP 6-in

Rear componentsFigure 1-4 Rear componentsTable 1-3 Rear componentsComponent Component1 Access panel 8 (2) USB 3.0 ports2 Access panel latches 9 RJ-4

Keyboard featuresFigure 1-5 Keyboard featuresTable 1-4 Keyboard featuresComponent Component1 Sleep 6 Mute Volume2 Fast Reverse 7 Decrease Volume3 Pl

Positioning the computerThis computer may be shipped with no stand, with a height-adjustable stand, or a tilt/swivel stand.The computer may be placed

WARNING! If the height-adjustable/recline stand is installed, before laying the computer down forservice, first grasp the sides of the display and rai

Figure 1-10 Adjusting swivelWaking the computerTo wake the HP EliteOne 800 G1 Touch All-in-One:▲To wake the computer from standby using the touch fea

2 Hardware repair and upgradeWarnings and cautionsBefore performing upgrades be sure to carefully read all of the applicable instructions, cautions, a

Additional informationFor more information on removing and replacing hardware components, the Computer Setup utility,and troubleshooting, refer to the

Installing the rear port cover1. Be sure that all cables are connected.2. Hold the cover close to the computer (1) and line up the right edge of the c

4. Plug the power cord into the power connection on the rear of the computer (1).Figure 2-3 Connecting power5. Plug the three-pronged power plug into

© Copyright 2013 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Windows is either a trade

Disconnecting power1. Remove all removable media, such as compact discs or USB flash drives, from the computer.2. Turn off the computer properly throu

Installing an access panel security screwYou may prevent access to internal components and ports by securing the access panel and rear portcover. Scre

4. Insert the wireless receiver into a USB port on the computer.Figure 2-7 Installing the wireless receiver5. Press and hold the Connect button on th

Removing batteries from the optional wireless keyboardor mouseNOTE: The wireless keyboard and mouse are optional components.To remove batteries from t

Attaching the computer to a mounting fixtureYou can remove the computer from the stand and install it on a wall, monitor arm, or other mountingfixture

Installing and removing a standTwo stands are available for the computer:●Height-adjustable/recline stand●Tilt/swivel standInstalling and removing a h

3. Tighten the four captive screws to secure the stand to the chassis.Figure 2-12 Securing the standRemoving a height-adjustable/recline standTo remo

5. Place the computer face down on a soft flat surface. HP recommends that you set down ablanket, towel, or other soft cloth to protect the bezel and

7. Lift the stand up and off the computer.Figure 2-15 Removing the standInstalling and removing a tilt/swivel stand (optional)Installing a tilt/swive

4. Tighten the captive screws to secure the stand to the chassis.Figure 2-17 Securing the stand5. Align the top of the back of the stand with the sta

About This BookThis guide provides basic information for upgrading this computer model.WARNING! Text set off in this manner indicates that failure to

5. Place the computer face down on a soft flat surface. HP recommends that you set down ablanket, towel, or other soft cloth to protect the bezel and

8. Lift the stand up and off the computer.Figure 2-21 Removing the standConnecting a second displayThe DisplayPort connector on the rear of the compu

3. If your second display has a DisplayPort connector, connect a DisplayPort cable directlybetween the DisplayPort connector on the rear of the comput

4. If your second display does not have a DisplayPort connector, connect a DisplayPort videoadapter to the DisplayPort connector of the computer. Then

Locating internal componentsThe following sections contain procedures for removing and replacing these internal components:●Memory●Battery●Hard disc d

Removing and installing memoryThe computer comes with double data rate 3 synchronous dynamic random access memory (DDR3-SDRAM) small outline dual inli

Populating SODIMM socketsThe system will automatically operate in single channel mode, dual channel mode, or flex mode,depending on how the SODIMMs ar

6. Slide the access panel latches toward the edges of the unit, then slide the access panel towardthe top of the computer until it slides off the unit

8. To install a memory module, slide the SODIMM into the socket at approximately a 30° angle (1),then press the SODIMM down (2) so that the latches lo

Replacing the batteryThe battery is located on the system board on the lower right side of the fan. The battery that comeswith the computer provides p

iv About This Book

6. Slide the access panel latches toward the edges of the chassis, then slide the access paneltoward the top of the computer until it slides off the c

8. To insert the new battery, slide one edge of the replacement battery under the holder’s lip withthe positive side up. Push the other edge down unti

Replacing drivesReplacing a hard disc driveThe hard disc drive is located behind the access panel on the lower left side of the computer (whenviewed f

7. Pull the latch next to the lower side of the 2.5-inch hard disc drive cage away from the cage torelease it, then slide the cage toward the edge of

Installing a 2.5-inch hard disc drive1. Insert the 2.5-inch hard disc drive into the drive cage.●To install a primary hard disc drive, insert the driv

3. Fasten an upper 2.5-inch hard disc drive securely in place with the four standard screws thatshipped with the drive.4. Position the 2.5-inch drive

6. To replace the access panel, set the panel on the back of the computer, slightly above the stand,and slide it down into place.Figure 2-39 Replacin

6. Slide the access panel latches toward the edges of the chassis, then slide the access paneltoward the top of the computer until it slides off the c

8. Pull the latch off the optical disc drive.Figure 2-42 Removing the optical disc drive latch9. Remove the cover from the adhesive strip on the new

10. Align the new optical disc drive with the opening in the side of the computer. Push the drive infirmly until it snaps into place.NOTE: The optical

Table of contents1 Product features ...

A Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

B Computer operating guidelines, routinecare, and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properl

damp cloth to gently wipe the screen surface. Never spray the cleaner directly on thescreen surface. It may run behind the bezel and damage the electr

IndexAadditional information 11Bbattery replacement 33Ccomponentsfront 3internal 28rear 5side 4computer operating guidelines 45DDisplayPort video adap

location 30specifications 29specifications, memory 29standheight-adjustable/recline,installing 19height-adjustable/recline,removing 20tilt/swivel stan

Connecting a second display ... 25Locating i

1 Product featuresOverviewFigure 1-1 HP EliteOne 800 G1 All-in-OneThe HP EliteOne 800 G1 All-in-One offers the following features:● Integrated All-in

●Optional Tray-load HP SuperMulti DVD+/-RW SATA Optical Disc Drive, DVD-ROM disc drive, orSlim BDXL Blu-ray Writer●Intel Q87 Express chipset – Intel v

Front componentsFigure 1-2 Front componentsTable 1-1 Front componentsComponent Component1 Webcam (optional) with privacy shutter 7 Mute speaker2 Dua