HP 10BASE-T Betriebsanweisung Seite 33
- Seite / 136
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5. Connect the Hub to the Distributed
Management Console (optional)
The HP AdvanceStack hubs can be controlled in two ways:
from a PC running the HP Stack Manager software that is supplied
with the hubs
from an ASCII terminal or PC running a terminal emulation (requires
an HP Ethernet SNMP Module to be installed in the hub or in one of
the hubs in the distributed management chain)
The PC serves as a console for an out-of-band management session that
enables you to configure, monitor, and diagnose one hub or a stack of up
to 16 hubs that are chained together. The HP Stack Manager software is
described in chapter 2, “Installing and Using HP Stack Manager”.
With the HP Ethernet SNMP Module, the module’s console is also used
to configure, monitor, and diagnose one hub or a stack of up to 16 hubs
that are chained together. You can access the console through a terminal
emulator on your PC or through a terminal.
There are three ways to access a hub:
through a direct serial connection
through a modem connection (available for HP Stack Manager or
ASCII terminal only if an HP J6203 Ethernet SNMP Module is
installed in the hub to which the modem is connected)
through the distributed management chain
Installing the
HP AdvanceStack Hubs
Installing the HP AdvanceStack 10Base-T Hubs
1-20
- HP AdvanceStack 10Base-T Hubs 1
- All Rights Reserved 2
- Features 4
- (continued on next page) 4
- (continued) 5
- HP Customer Support Services 7
- Contents 8
- 3 Hub Reference 10
- 4 Troubleshooting 11
- A Cables and Connectors 12
- B Specifications 12
- C Network Addressing 12
- D Backup Links 13
- 10Base-T Hubs 14
- Installation Summary 15
- Installation Steps 16
- 2. Verify the Hub’s Operation 17
- 3. Mount the Hub 18
- 10-mm M4 19
- Important 20
- Mounting the Hub on a Wall 23
- to the Hub 24
- Distributed Management 26
- Network Port Connections 27
- 24681012 1357911 28
- 10Base-T 28
- 24681012 28
- Cable Management 32
- Installing and Using 38
- HP Stack Manager 38
- Software Description 39
- Computer Requirements 40
- Installing and Starting 41
- Communications Settings 43
- Connect/Disconnect 43
- Automatic Chain Display 44
- Online Help 44
- Port Status Display 44
- LAN Traffic Statistics 44
- Hub Identification 44
- Port Enable/Disable 45
- Port Counters 45
- Redundant Power Supply (RPS) 45
- Advanced Features 46
- IP Configuration 47
- Password 47
- Authorized Managers 48
- Backup Link 48
- Robust Port Control 48
- Network Tests 49
- Factory Reset 49
- Hub Reference 50
- Front Panel 51
- Back Panel 51
- Front of the hub 52
- How the Hubs Work 54
- Auto-Segmentation 55
- Link Beat 56
- Managing Your Hub — 57
- HP Distributed Management 57
- Chaining the Hubs 58
- Out-of-Band Management 58
- In-Band (Network) Management 58
- Security Features 59
- Port Security 60
- Authorized Managers List 60
- Optional Modules 61
- HP Transceiver Modules 63
- HP Router Module 64
- HP Dial-a-LAN Remote Access 66
- HP J2624A Dial-A-LAN 4A 67
- Firmware Enhancements 68
- Troubleshooting 70
- Troubleshooting Approaches 71
- Diagnosing with the LEDs 72
- LED Error Indications 73
- Installation Problems 75
- Cabling Problems 76
- Unusual Network Activity 77
- IP Configuration Errors 77
- Diagnostic Tests 78
- Testing Twisted-Pair Cabling 79
- Clearing a Password 80
- Customer Support Services 81
- CompuServe 83
- Cables and Connectors 86
- Recommended Cables 88
- Twisted-Pair Cable/Connector 89
- Pin-Outs 89
- Management Chaining 90
- (not a network connection) 90
- Hub-to-Hub Network Connection 91
- ThinLAN Cable Requirements 92
- AUI Cable Minimum Pin-Out 93
- RS-232 Connector and Cable 94
- RS-232-C “Null Modem” Cable 95
- (supplied with the hub) 95
- RS-232-C Modem Cable 95
- Specifications 96
- Network Addressing 100
- Communication Between the Hub 101
- IPX Addressing Notes: 102
- Networks 103
- Using BOOTP 105
- This tag must precede the 106
- For the HP 106
- Backup Links 108
- Description 109
- Limitations 110
- Additional Notes 110
- Configuring a Backup Link 111
- Identifying the Backup Link 112
- Indications of Backup Link 113
- Activation 113
- Reactivating the Primary Link 114
- Example Topologies 115
- Safety Information 119
- Symboles de sécurité 120
- Safety and Regulatory 120
- Statements 120
- Hinweise zur Sicherheit 121
- Simboli di sicurezza 122
- Símbolos de seguridad 123
- Regulatory Statements 125
- Declaration of Conformity 126
- *5964-4601* 136
Verwandte Produkte und Handbücher für Vernetzung HP 10BASE-T
Vernetzung HP 3.1.X Bedienungsanleitung
(307 Seiten)
(307 Seiten)
Vernetzung HP 24S Betriebsanweisung
(102 Seiten)
(102 Seiten)
Vernetzung HP WL210 Installationsanleitung
(76 Seiten)
(76 Seiten)
Vernetzung HP sa2250 Schnellstart Anleitung
(26 Seiten)
(26 Seiten)
Vernetzung HP hn200e Bedienungsanleitung
(90 Seiten)
(90 Seiten)
Vernetzung HP 04H8095 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Vernetzung HP 10.8TB Installationshandbuch
(6 Seiten)
(6 Seiten)
(10 Seiten)
Vernetzung HP hp-ux 11.0 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Vernetzung HP tx2-1002au Betriebsanweisung
(16 Seiten)
(16 Seiten)
Vernetzung HP 100VG Betriebsanweisung
(116 Seiten)
(116 Seiten)
Vernetzung HP B3000 Installationsanleitung
(28 Seiten)
(28 Seiten)
Vernetzung HP A6826A Bedienungsanleitung
(40 Seiten)
(40 Seiten)
Vernetzung HP 289166-40B Bedienungsanleitung
(19 Seiten)
(19 Seiten)
Vernetzung HP 2103R-CSDI Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Western Reserve Controls 1782-JDC manuály
Uživatelské manuály a uživatelské příručky pro Brány / ovladače Western Reserve Controls 1782-JDC.
Poskytujeme 3 manuály pdf Western Reserve Controls 1782-JDC ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern