Hp ProBook 5220m Notebook PC Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Notebooks Hp ProBook 5220m Notebook PC herunter. HP ProBook 5220m Notebook PC User Manual [en] Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 145
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - HP ProBook Notebook PC

HP ProBook Notebook PCUser Guide

Seite 2

Securing system devices ... 99Viewing Computer Setup S

Seite 3 - Safety warning notice

7. Slide the service access door latches (1) inward. Slide the service access door toward the batterybay. Then lift up the forward edge of the service

Seite 4

9. Insert a new memory module:a. Align the notched edge (1) of the memory module with the tab in the memory module slot.CAUTION: To prevent damage to

Seite 5 - Table of contents

12. Slide the lock latch (4) to the right until it locks.NOTE: You can identify the lock latch by the red marking on the latch.13. Replace the battery

Seite 6

10 SecurityProtecting the computerNOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent aproduct from being mis

Seite 7

Using passwordsMost security features use passwords. Whenever you set a password, write down the password andstore it in a secure location away from t

Seite 8

BIOS administrator passwords FunctionDriveLock master password Protects access to the internal hard drive that is protected byDriveLock. It is also us

Seite 9

To change this password in Computer Setup, follow these steps:1. Turn on or restart the computer, and then press esc while the “Press the ESC key for

Seite 10

Using Computer Setup DriveLockCAUTION: To prevent the DriveLock-protected hard drive from becoming permanently unusable,record the DriveLock user pass

Seite 11

NOTE: The DriveLock confirmation is case sensitive.11. To save your changes and exit Computer Setup, click Save in the lower-left corner of the screen

Seite 12

Removing DriveLock protectionTo remove DriveLock protection in Computer Setup, follow these steps:1. Turn on the computer, and then press esc while th

Seite 13 - 1 Features

Dynamically choosing a boot device using the F9 prompt ... 124Setting a MultiBoot Express prompt ...

Seite 14 - 2 Chapter 1 Features

Removing Automatic DriveLock protectionTo remove DriveLock protection in Computer Setup, follow these steps:1. Turn on or restart the computer, and th

Seite 15 - Identifying hardware 3

Using Computer Setup security featuresSecuring system devicesYou can disable or enable system devices from the following menus in Computer Setup:●Boot

Seite 16 - 4 Chapter 1 Features

Viewing Computer Setup System InformationThe System Information feature in Computer Setup provides 2 types of system information:●Identification infor

Seite 17 - Front components

Using antivirus softwareWhen you use the computer to access e-mail, a network, or the Internet, you expose the computer tocomputer viruses. Computer v

Seite 18 - Right-side components

Using HP ProtectTools Security Manager (select modelsonly)HP ProtectTools Security Manager software is preinstalled on select computer models. This so

Seite 19 - Left-side components

Using the fingerprint readerNOTE: The location of the fingerprint reader varies by computer model.Locating the fingerprint readerThe fingerprint reade

Seite 20 - Bottom components

Enrolling your fingerprintsIf your computer has a fingerprint reader built in or connected, the HP ProtectTools Security ManagerSetup wizard guides yo

Seite 21 - Wireless antennas

11 Software updatesUpdating softwareUpdated versions of the software provided with your computer are available either through the HPSoftware Update ut

Seite 22 - 10 Chapter 1 Features

To update the software using the HP Web site, follow these steps:1. Identify your computer model, product category, and series or family. Prepare for

Seite 23 - Identifying the labels

Downloading a BIOS updateCAUTION: To prevent damage to the computer or an unsuccessful installation, download and installa BIOS update only when the c

Seite 25 - Using wireless devices

NOTE: After a message on the screen reports a successful installation, you may delete thedownloaded file from your hard drive.Updating programs and dr

Seite 26 - Using the wireless controls

models. Select Show software for all supported models. If you have used HP SoftPaq DownloadManager previously, go to step 3.a. Select your operating s

Seite 27 - Using the wireless hotkey

12 Backup and recoveryTo protect your information, use the Windows® Backup utility (select models only) to back up files andfolders or create recovery

Seite 28 - Using a WLAN device

Backing up your informationRecovery after a system failure is as complete as your most current backup. You should create yourinitial backup immediatel

Seite 29 - Protecting your WLAN

Performing a recoveryIn case of system failure or instability, the computer provides the following tools to recover your files:●Windows recovery tools

Seite 30 - Roaming to another network

13 Computer SetupStarting Computer SetupComputer Setup is a preinstalled, ROM-based utility that can be used even when the operating systemis not work

Seite 31 - Inserting a SIM

To exit Computer Setup menus, choose one of the following methods:●To exit Computer Setup menus without saving your changes, click the Exit icon in th

Seite 32 - Removing a SIM

File menuSelect To do thisSystem Information●View identification information for the computer and thebatteries in the system.●View specification infor

Seite 33

Select To do thisUser Management (requires a BIOS administrator password)●Create a new BIOS user account.●View a list of ProtectTools users.Password P

Seite 34

Select To do thisBoot Options●Set a Startup Menu delay (in seconds).●Set the MultiBoot Express Boot Popup delay in seconds.●Enable/disable Custom Logo

Seite 35

1 FeaturesIdentifying hardwareComponents included with the computer may vary by region and model. The illustrations in this chapteridentify the standa

Seite 36 - WLAN connection is very weak

Select To do thisNOTE: Availability of the options above varies bycomputer model.●Enable/disable HP DayStarter (enabled by default).●Enable/disable HP

Seite 37

Select To do thisBuilt-In Device Options●Enable/disable the wireless button state (enabled bydefault).●Enable/disable the embedded WLAN device (enable

Seite 38 - Using the modem

Select To do thisSet Security Level Change, view, or hide security levels for all BIOS menu items.Restore Security Defaults Restore the default securi

Seite 39 - Selecting a location setting

14 MultiBootAbout the boot device orderAs the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility,which is e

Seite 40

Enabling boot devices in Computer SetupThe computer will boot to a USB device or a NIC device only if the device has first been enabled inComputer Set

Seite 41

Considering boot order changesBefore changing the boot order, note the following considerations:●When the computer restarts after the boot order has b

Seite 42 - Using pointing devices

Choosing MultiBoot preferencesYou can use MultiBoot in the following ways:●To set a new boot order that the computer uses each time it is turned on, b

Seite 43 - Using the TouchPad

Setting a MultiBoot Express promptTo start Computer Setup and set the computer to display the MultiBoot startup location menu each timethe computer is

Seite 44 - Using TouchPad gestures

15 Management and printingUsing Client Management SolutionsClient Management Solutions software provides standards-based solutions for managing client

Seite 45

Managing and updating softwareHP provides HP SSM (System Software Manager) for managing and updating software on clientcomputers.HP SSM (System Softwa

Seite 46

Component Description(2) TouchPad* Moves the pointer and selects or activates items on the screen.(3) Left TouchPad control* Functions like the left b

Seite 47 - Using the keyboard

IndexAAC adapterconnecting 58identifying 11administrator password 92airport security devices 70antennas 9applications key, Windows 5audio devices, con

Seite 48 - Initiating Standby

setting MultiBoot Expressprompt 125System Configurationmenu 116computer setup 113Computer Setup utility 126connecting to a LAN 25connecting to a WLAN

Seite 49 - Opening QuickWeb

switching screen image 37using 36HP 3D DriveGuard 72HP Broadband WirelessModule 13HP Connection Managersoftware 15HP DayStarter 118HP FastLook 39, 11

Seite 50

Ooperating systemMicrosoft Certificate ofAuthenticity label 12Product Key 12operating system controls 16Operating System disc 112optical discinserting

Seite 51 - Using keypads

updating 105updating programs anddrivers 108sound mute light 3speakersidentifying 5Standbyexiting 54initiating 54Standby hotkey 36start-up test 115sto

Seite 53

Component Description(6) Wireless light●White: An integrated wireless device, such as a wireless localarea network (WLAN) device, HP Mobile Broadband

Seite 54 - 4 Multimedia

Component Description(1) Power button●When the computer is off, press the button to turn onthe computer.●When the computer is on, press the button to

Seite 55 - Adjusting the volume

Component Description(2) fn key Executes frequently used system functions when pressed incombination with a function key or the esc key.(3) Windows lo

Seite 56 - Multimedia software

Right-side componentsComponent Description(1) Battery light●Amber: A battery is charging.●White: A battery is close to full charge capacity.●Off: If t

Seite 57

Component Description(5) Audio-out (headphone)/Audio-in (microphone)jackProduces sound when connected to optional powered stereospeakers, headphones,

Seite 58 - Connecting an HDMI device

© Copyright 2010 Hewlett-PackardDevelopment Company, L.P.Bluetooth is a trademark owned by itsproprietor and used by Hewlett-PackardCompany under lice

Seite 59 - Configuring audio for HDMI

Bottom componentsComponent Description(1) Battery release latches (2) Release the battery from the battery bay.(2) Battery bay Holds the battery and t

Seite 60 - Playing music

Display components Component Description(1) Internal display switch Turns off the display and initiates Standby if the display is closedwhile the powe

Seite 61 - Watching a movie

Component Description(1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate withwireless wide-area networks (WWA

Seite 62 - Changing DVD region settings

Additional hardware componentsComponent Description(1) Power cord* Connects an AC adapter to an AC outlet.(2) AC adapter Converts AC power to DC power

Seite 63

◦Part number/Product number (p/n) (3). This number provides specific information about theproduct's hardware components. The part number helps a

Seite 64 - Webcam (select models only)

2 Wireless, local area network, andmodemUsing wireless devicesWireless technology transfers data across radio waves instead of wires. Your computer is

Seite 65 - Adjusting webcam properties

Identifying wireless and network iconsIcon Name DescriptionWireless (connected) Identifies the location of the wireless light and the wireless hotkey

Seite 66 - 5 Power management

Using the wireless hotkeyThe computer has a wireless hotkey (fn+f9), one or more wireless devices, and one or two wirelesslights, depending on the mod

Seite 67 - Using the Power Meter

Using operating system controlsSome operating systems also offer a way to manage integrated wireless devices and the wirelessconnection. For example,

Seite 68 - Using power schemes

Protecting your WLANBecause the WLAN standard was designed with only limited security capabilities—basically to foil casualeavesdropping rather than m

Seite 69 - Using HP Power Assistant

Safety warning noticeWARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do notplace the computer directly on

Seite 70 - Using external AC power

Connecting to a WLANTo connect to the WLAN, follow these steps:1. Be sure that the WLAN device is on. If it is on, the wireless light is white. If the

Seite 71 - Using battery power

is a mobile phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voicecoverage.When used with mobile network operator s

Seite 72

7. Insert the SIM into the SIM slot, and gently slide the SIM into the slot until it is firmly seated.8. Replace the battery.NOTE: HP Mobile Broadband

Seite 73

7. Press in on the SIM (1), and then remove it from the slot (2).8. Replace the battery.9. Turn the computer right-side up.10. Reconnect external powe

Seite 74 - Managing low battery levels

Using a Bluetooth wireless device (select models only)A Bluetooth device provides short-range wireless communications that replace the physical cablec

Seite 75 - Resolving a low battery level

NOTE: Windows includes the User Account Control feature to improve the security of your computer.You may be prompted for your permission or password f

Seite 76 - Calibrating a battery

NOTE: If the WLAN device you are using was purchased separately, consult the manufacturer's Website for the latest software.Current network secur

Seite 77 - Step 3: Discharge the battery

A list showing the available WLANs is displayed. If you are in a hotspot where several WLANs areactive, several will be displayed.4. Select a network,

Seite 78 - Storing a battery

Using the modemThe modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable(purchased separately). In some countries or re

Seite 79 - Replacing the battery

Connecting a country- or region-specific modem cable adapterTelephone jacks vary by country or region. To use the modem and the modem cable (purchased

Seite 81 - Handling drives

CAUTION: To prevent losing your home country or region settings, do not delete your current modemcountry or region settings. To enable modem use in ot

Seite 82

To determine the dialing mode supported by a telephone line, dial a few digits on the telephone,and then listen for clicks (pulses) or tones. Clicks i

Seite 83 - Using Disk Cleanup

3 Pointing devices and keyboardComponent Description(1) TouchPad off indicator●When the TouchPad is active, the light is off.●When the TouchPad is ina

Seite 84 - Using HP 3D DriveGuard

Using the TouchPadTurning the TouchPad on and offThe TouchPad is turned on at the factory. When the TouchPad is active, the light is off.To turn the T

Seite 85

SelectingUse the left and right TouchPad controls like the corresponding controls on an external mouse.Using TouchPad gesturesThe TouchPad supports a

Seite 86 - Replacing a hard drive

NOTE: You can scroll and pinch anywhere on the TouchPad surface, including the control area.However, the rotate gesture can be done only on the TouchP

Seite 87

RotatingRotating allows you to rotate items such as photos and pages. To rotate these items, anchor your leftforefinger on the TouchPad. Move the righ

Seite 88

Connecting an external mouseYou can connect an external USB mouse to the computer using one of the USB ports on the computer.A USB mouse can also be c

Seite 89 - 7 External devices

Function HotkeyDisplay system information fn+escInitiate Standby fn+f1Open the Print Options window fn+f2Open HP Power Assistant fn+f3Switch the scree

Seite 90 - Using USB legacy support

To exit Standby, briefly press the power button or press any key on the keyboard.The function of the fn+f1 hotkey can be changed. For example, you can

Seite 91 - Using an eSATA device

Table of contents1 Features ...

Seite 92 - Removing an eSATA device

Decreasing screen brightnessPress fn+f7 to decrease screen brightness. Hold down the hotkey to decrease the brightness levelincrementally.Increasing s

Seite 93

Using HP FastLookFastLook allows you to view and manage calendar, contact, inbox, and task information from MicrosoftOutlook, even when the computer i

Seite 94

NOTE: The embedded numeric keypad will not function while an external keyboard or numeric keypadis connected to the computer, an optional docking devi

Seite 95

Cleaning the TouchPad and keyboardDirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this,clean the TouchPad

Seite 96

4 MultimediaMultimedia featuresYour computer includes multimedia features that allow you to listen to music and view pictures. Yourcomputer may includ

Seite 97 - 8 External media cards

Component Description(1) Internal microphone Records sound.(2) Webcam (select models only) Records audio and video and captures still photographs.(3)

Seite 98

◦To increase volume, press fn+f12.●Windows volume control:a. Click the Volume icon in the notification area, at the far right of the taskbar.b. Increa

Seite 99 - 9 Memory modules

Accessing your preinstalled multimedia softwareTo access your preinstalled multimedia software:▲Select Start > All Programs, and then open the mult

Seite 100

To connect external devices such as external speakers, headphones, or a microphone, refer to theinformation provided with the device. For best results

Seite 101

To connect a video or audio device to the HDMI port:1. Connect one end of the HDMI cable to the HDMI port on the computer.2. Connect the other end of

Seite 102

Troubleshooting wireless network problems ... 22Cannot create a WLA

Seite 103 - 10 Security

Connecting an external monitor or projectorThe external monitor port connects an external display device such as an external monitor or a projectorto

Seite 104 - Using passwords

5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place.6. Close the disc tray.7. If you have not selected a media pla

Seite 105 - BIOS administrator password

5. Gently press the disc (3) down onto the tray spindle until the disc snaps into place.6. Close the disc tray.NOTE: After you insert a disc, a short

Seite 106

Creating (burning) a CD or DVDCAUTION: Observe the copyright warning. It is a criminal offense, under applicable copyright laws,to make unauthorized c

Seite 107 - Setting a DriveLock password

2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outeredges of the disc. Hold the disc by the edges and a

Seite 108 - Changing a DriveLock password

Webcam tipsFor optimum performance, observe the following guidelines while using the webcam:●Be sure that you have the latest version of an instant me

Seite 109 - Removing DriveLock protection

5 Power managementSetting power optionsUsing power-saving statesThe computer has two power-saving states enabled at the factory: Standby and Hibernati

Seite 110

When the computer exits Standby, the power lights turn on and your work returns to the screenwhere you stopped working.NOTE: If you have set a passwor

Seite 111 - Securing system devices

To show the Power Meter icon in the notification area, follow these steps:1. Select Start > Control Panel > Performance and Maintenance > Pow

Seite 112

3. Modify the Plugged in and Running on batteries settings as needed.4. Click OK.Setting password protection upon exiting StandbyTo set the computer t

Seite 113 - Using firewall software

Increasing speaker volume ... 38Using HP FastLook ...

Seite 114 - Installing a security cable

Using external AC powerExternal AC power is supplied through one of the following devices:WARNING! To reduce potential safety issues, use only the AC

Seite 115 - Using the fingerprint reader

3. Plug the other end of the power cord into an AC outlet (3).NOTE: Your computer may look slightly different from the illustration in this section.Us

Seite 116 - Enrolling your fingerprints

To run Battery Check:1. Connect the AC adapter to the computer.NOTE: The computer must be connected to external power for Battery Check to function pr

Seite 117 - 11 Software updates

3. Slide the battery lock (3) to the right to lock the battery into place.To remove the battery:1. Turn the computer upside down on a flat surface, wi

Seite 118 - Updating the BIOS

Charging a batteryWARNING! Do not charge the computer battery while you are onboard aircraft.The battery charges whenever the computer is plugged into

Seite 119 - Downloading a BIOS update

Identifying low battery levelsWhen a battery that is the sole power source for the computer reaches a low battery level, the batterylight blinks.If a

Seite 120 - Updating programs and drivers

Calibrating a batteryCalibrate a battery under the following conditions:●When battery charge displays seem inaccurate●When you observe a significant c

Seite 121

Step 3: Discharge the batteryThe computer must remain on while the battery is being discharged. The battery can discharge whetheror not you are using

Seite 122 - 12 Backup and recovery

Step 4: Fully recharge the batteryTo recharge the battery:1. Plug the computer into external power and maintain external power until the battery is fu

Seite 123 - Backing up your information

Disposing of a used batteryWARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not shortexternal contacts; do not

Seite 124 - Performing a recovery

Customizing power schemes ... 56Setting password protection upon exiting Stan

Seite 125 - 13 Computer Setup

Testing an AC adapterTest the AC adapter if the computer exhibits any of the following symptoms:●The computer will not turn on when connected to the A

Seite 126 - Computer Setup menus

6DrivesIdentifying installed drivesYour computer includes a hard drive (with a rotating disc) or a solid-state drive (SSD) with solid-statememory. Bec

Seite 127 - Security menu

CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information,observe these precautions:Before you move a computer

Seite 128 - System Configuration menu

Improving hard drive performanceUsing Disk DefragmenterAs you use the computer, files on the hard drive become fragmented. Disk Defragmenter consolida

Seite 129 - Computer Setup menus 117

Using HP 3D DriveGuardHP 3D DriveGuard protects the hard drive by parking the drive and halting I/O requests under either ofthe following conditions:●

Seite 130

To open the software and change settings, follow these steps:1. Double-click the icon in the notification area, at the far right of the taskbar.– or –

Seite 131 - Computer Setup menus 119

Replacing a hard driveCAUTION: To prevent information loss or an unresponsive system:Shut down the computer before removing the hard drive from the se

Seite 132 - Select To do this

10. Pull up the hard drive tab (3), and then lift the hard drive out of the service access bay.To install a hard drive:1. Pull up the hard drive tab (

Seite 133

5. Press down on the door (2) until the until the release latch (3) clicks.6. Slide the lock latch (4) to the right to lock the door into place.NOTE:

Seite 134

7 External devicesUsing a USB deviceUniversal Serial Bus (USB) is a hardware interface that can be used to connect an optional externaldevice, such as

Seite 135

Using HP 3D DriveGuard software ... 72Replacing a hard drive ...

Seite 136

Stopping and removing a USB deviceCAUTION: To prevent loss of information or an unresponsive system, stop a USB device beforeremoving it.CAUTION: To p

Seite 137

Using an eSATA deviceNOTE: The eSATA port also supports an optional USB device.An eSATA port connects an optional high-performance eSATA component, su

Seite 138 - 15 Management and printing

Removing an eSATA deviceCAUTION: To prevent loss of information or an unresponsive system, use the following procedure tosafely remove an eSATA device

Seite 139

Using optional external drivesRemovable external drives expand your options for storing and accessing information. A USB drive canbe added by connecti

Seite 140

4. Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side upover the tray spindle.NOTE: If the tray is not fu

Seite 141

2. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outeredges of the disc. Hold the disc by the edges and a

Seite 142

3. Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outeredges of the disc. Hold the disc by the edges and a

Seite 143

8 External media cardsUsing Media Card Reader cardsOptional digital cards provide secure data storage and convenient data sharing. These cards are oft

Seite 144

2. Insert the card into the Media Card Reader, and then push in on the card until it is firmly seated.You will hear a sound when the device has been d

Seite 145

9 Memory modulesThe computer has two memory module slots, which are located on the bottom of the computer, insidethe service access door. The memory c

Kommentare zu diesen Handbüchern

Keine Kommentare