Hp LC 2000 Bedienungsanleitung Seite 166
- Seite / 194
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 13 Alternative Rack Mounting
158
The captive nuts are located near the external SCSI Connector (knockout)
location.
Cable Management Arm
Rear of HP NetServer
Left Rear
Rack Column
Figure 13-11. Attaching the Cable Management Arm
5. Attach the other flange of the cable arm to the rear column of the rack with
the two M-5 pan head T-25 Torx screws, included with the Arm.
6. Attach the flange to the NetServer with the two 8-32 pan head Torx T-20
screws, included with the Arm. See Figure 13-11.
7. Extend the NetServer out of the rack to ensure the Cable Management Arm
moves along with the chassis without binding.
NOTE Refer to the HP NetServer LC 2000r Rack Cabling Reference
Guide, for information about cable dressing and routing.
8. If the Cable Management Arm moves with the chassis and the rack
installation appears to be successful, slide the NetServer into the rack.
The NetServer should click into the latch on the two column adapters.
9. If the NetServer is not in a restricted-access area, tighten both slide
securing screws on the bezel latching mechanisms. See Figure 13-12.
- HP NetServer LC 2000/2000r 1
- Installation Guide 1
- Contents 3
- 1 Setting Up the HP NetServer 9
- Pedestal Installation 10
- Rack Mount Installation 13
- Front of HP NetServer 17
- Front Panel LED Indicators 19
- Power Supply Module Indicator 23
- Keyboard Mouse 24
- Video NIC 24
- (Embedded) 24
- Management 24
- NIC Indicators 25
- Link/Activity 25
- Transfer Rate 25
- Powering Up the HP NetServer 26
- Sleep States (ACPI) 27
- 3 Opening and Closing the HP 29
- NetServer 29
- Foot (4) 31
- Anti-Tip 31
- Foot Extended 31
- Slide Securing Screws (2) 33
- Hinge Pins(3) Handles(2) 33
- Top Cover 35
- Bottom Cover 35
- Cover Pull 35
- Right Cover 38
- Thumbscrews (2) 38
- Removing the Pedestal 40
- Hardware Mirroring 43
- Mass Storage Guidelines 44
- • General Guidelines 44
- • SCSI Device Selection 44
- • SCSI Drive Addressing 45
- • Filler Panels and Spacers 46
- Filler Panels 47
- Pedestal Configurations for 48
- Note: Con = Connector 49
- Connectors A and B 50
- Con = Connector 50
- Cabling Configurations 51
- Drive Spacer 55
- Locking Latch 56
- Removing Hot Swap Hard Drives 58
- Non-Hot Swap 59
- (Optional) 59
- DIMM Installation 64
- DIMM Removal 67
- Boot Priority 70
- IRQ Settings 71
- System Board PCI Slots 71
- Installing Accessory Boards 73
- 1. Open Tab 75
- 2. Lift Latch 75
- 3. Remove Slot Cover 75
- 1. Insert Board 77
- 2. Close Latch 77
- 3. Turn Tab 77
- Figure 7-1. System Board 80
- Installing the Processor 81
- Processor Cage 83
- Terminator 84
- Figure 7-6. Installing VRM 86
- Channel(2) 97
- Rear of HP NetServer 101
- Left Rear 101
- Rack Column 101
- Cable Management Arm 101
- Attaching the Front Bezel 102
- Mouse, and UPS 105
- Introduction 107
- HP NetServer Navigator CD-ROM 107
- Internet FTP 109
- Assistant 111
- • Show System Information: 113
- • Configure Disk Array: 113
- • Install Utility Partition: 113
- • Execute Card Utilities: 113
- NOS Installation 115
- HP Management Solutions 116
- Setup Utility 120
- Using the Setup Screens 121
- • Small arrow points ( 122
- ➢Hardware Security 123
- Floppy check: [Disabled] 126
- Summary screen: [Enabled] 126
- Quick Boot mode: [Enabled] 126
- ➢Boot Device Priority 126
- ➢Hard Drive Priority 126
- Clearing CMOS 128
- SCSI Configuration Utility 129
- 11 Information Assistant 135
- Installing from the CD-ROM 137
- :\infoasst\setup 137
- 12 Troubleshooting 139
- Common Installation Problems 140
- Chapter 12 Troubleshooting 141
- Error Message Is Displayed 142
- No Error Messages Displayed 143
- Open = Off 145
- Closed = On 145
- Hardware Problems 147
- Keyboard or Mouse Do Not Work 148
- CD-ROM Drive Does Not Work 148
- Password Problems 149
- Battery Problems 150
- 13 Alternative Rack Mounting 153
- Tools Required 154
- • Nut driver or wrench 154
- • T-15 and T-25 Torx Drivers 154
- • Marking pen 154
- Preparing the Rack 156
- Mounting 161
- Channels(2) 162
- A Specifications 169
- Appendix A Specifications 170
- Environmental Requirements 171
- Physical Requirements 172
- Video Support 173
- B Regulatory Information 175
- Notice for Japan 177
- Notice for Korea 178
- Notice for Taiwan 179
- Notice for European Union 179
- Battery Statements 183
- C Service and Support 185
- Warranty 187
Verwandte Produkte und Handbücher für Computers Hp LC 2000
Computers Hp XW6400X Bedienungsanleitung
(90 Seiten)
(90 Seiten)
Computers Hp 576X-B Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Computers Hp BL2X220C Bedienungsanleitung
(82 Seiten)
(82 Seiten)
Computers Hp Vectra VL 5/xxx Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Computers Hp BA322 90087 Bedienungsanleitung
(346 Seiten)
(346 Seiten)
Computers Hp XW6200 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Computers Hp ProLiant DL785 Bedienungsanleitung
(42 Seiten)
(42 Seiten)
Computers Hp LH 3r Bedienungsanleitung
(23 Seiten)
(23 Seiten)
Computers Hp S6150AP Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Computers Hp T550 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Computers Hp Vectra 500 Series Bedienungsanleitung
(146 Seiten)
(146 Seiten)
Computers Hp XW4300 Bedienungsanleitung
(85 Seiten)
(85 Seiten)
Computers Hp AD117-9003A-ED3 Bedienungsanleitung
(177 Seiten)
(177 Seiten)
Computers Hp TC2120 Bedienungsanleitung
(125 Seiten)
(125 Seiten)
Western Reserve Controls 1782-JDC manuály
Uživatelské manuály a uživatelské příručky pro Brány / ovladače Western Reserve Controls 1782-JDC.
Poskytujeme 3 manuály pdf Western Reserve Controls 1782-JDC ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern