Hp XW8400 Bedienungsanleitung

AUTODESK® LUSTRE® 2007A Discreet® Systems productHP xw8400 WORKSTATIONEdit the Document Title VariableHardware Setup Guide

Introduction16 For workflow information related to the HP xw8400 running on Linux for Incinerator, refer to the Autodesk Incinerator Installation an

Hardware Configuration Guidelines 7Consult the Autodesk Web site at www.autodesk.com/discreet-documentation for the latest version of guides, relea

Introduction18 Windows or Linux operating systems, HP xw8400 workstations, and peripherals associated with professional high-performance video and p

Hardware Configuration Guidelines 9The Flash System ROM confirmation menu appears.9. Press F10 to confirm.10. Press any key.System ROM Flash was su

Introduction110 System ROM Flash was successful appears.14. Verify system BIOS settings. See “Verifying BIOS Settings” on page 10.15. From the File

Hardware Configuration Guidelines 113. Press F10 to accept the changes. 4. Select Apply Defaults and Exit. This restores the original factory syste

Introduction112 load. Refer to the following table for standard conversion benchmarks and an example of how they are used to establish climate contr

Contacting Customer Support 13Contacting Customer SupportYou can contact Autodesk Media and Entertainment Customer Support at www.autodesk.com/supp

Introduction114 Customer support is also available through your Autodesk reseller. To find a reseller near you, consult the reseller look-up databas

15Connecting PeripheralsSummaryWorkflow for Connecting Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15C

Autodesk® Lustre® 2007© 2000-2006 Autodesk Canada Co./Autodesk, Inc. and/or its licensors. All rights reserved.All user documentation ("User Docu

Connecting Peripherals216 Connection Diagram for the HP xw8400The following diagrams show the connections for the HP xw8400 workstation. NOTE: These

Connecting the Monitor 17NOTE: The Slave Renderer option is not available for Lustre with Incinerator.Connecting the MonitorConnect the monitor to

Connecting Peripherals218 Connecting the Keyboard, Mouse, and Monitor Calibration DeviceConnect the mouse, keyboard, and monitor calibration device

Network Connections 19You can connect your workstation to two types of storage: • One or more Stone Direct disk arrays that provide storage to indi

Connecting Peripherals220 For Linux-based workstations, connect the integrated network port to the Incinerator private port. Refer to the Incinerato

21Connecting System ComponentsSummaryWorkflow for Connecting System Components in the Lustre Workgroup . . . . 21Connecting the Autodesk Control

Connecting System Components322 Connecting the Autodesk Control SurfaceThe Autodesk control surface consists of three panels. You can use any combin

Connecting the Autodesk Control Surface 23To connect the Autodesk control surface:1. Use the AC power adapter cables to connect each panel to a pow

Connecting System Components324 If you are using only one panel, you can connect that panel directly to the workstation, instead of using the switch

Assigning an IP Address to the Autodesk Control Surface 25NOTE: The above diagrams represent a Windows-based configuration. Components may differ s

contentsiiiContents1 Introduction 1Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting System Components326 4. Select the Use the following IP address option.5. Set a static IP and Subnet mask address for the port. Select va

Configuring Lustre to Connect to the Autodesk Control Surface 27Configuring Lustre to Connect to the Autodesk Control SurfaceAfter you have configu

Connecting System Components328 To connect a stand-alone tablet, connect the tablet to USB Out 1 on the USB extender.NOTE: On Windows-based workstat

Connecting the Slave Renderer to a Lustre Workstation 29Slave Render Station (HP DL140 G3)Port 1HP xw8400 Workstation(Windows-based)

Connecting System Components330 Connecting Video I/O to a Master or HD StationYou use the video components to set up video I/O and a broadcast monit

Connecting Video I/O to a Master or HD Station 31Video I/O without Real-Time DeliverablesThe following illustration shows the video I/O wiring for

Connecting System Components332 Connecting to a High-Speed Data Link Device (HSDL)If you have purchased an HSDL license, you can connect to an HSDL

Connecting to a High-Speed Data Link Device (HSDL) 33Connect both the A and B in/out ports on the DVS main board and daughter card to your HSDL dev

Connecting System Components334

index35IndexAair conditioningrequirements 11Autodesk control surfaceassigning an IP address 25configuration file 27connecting 22BBIOS settingsHP xw840

tentsConivWorkflow for Connecting System Components in the Lustre Workgroup . . . . . . . 21Connecting the Autodesk Control Surface. . . . . . . . .

36Indexconnecting 17mouseconnecting 18Nnetworkconnection 19Pperipheralsmonitor 17mouse and keyboard 18network 19tablet 27powerrequirements 11Rreal-tim

1IntroductionSummaryAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction12 NOTE: If you do not have Acrobat Reader, you can download a free copy from the Adobe Web site (www.adobe.com). If you do not have Xpd

Optional Lustre Components 3Lustre Station — Tasks that do not require the direct intervention or supervision of the colorist can be efficiently ha

Introduction14 Control Surface — The Autodesk control surface provides improved interactivity when colour grading film and video footage. You can pe

Workflow for Hardware Setup and Application Installation 5NOTE: For an Incinerator system configuration overview, refer to the Autodesk Incinerator