Hp 9000 V2600 SCA Bedienungsanleitung Seite 191
- Seite / 206
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix A 169
LED codes
Power on detected errors
1C-25 48V error
NPSLL failure
PWRUP=0-9
1. Error occurs when 48 volt
distribution falls below 42
volts during powerup state
displayed. Powerup state
indicates which loads are
being turned on.
2. Excessive load on 48 volts due
to an inadequate number of
functioning 48 volt supplies
or overload condition on 48V
bus.
3. Possible node power supply
(NPS) lower left failure.
Call the Response Center.
26-2F 48V error
NPSLR failure
PWRUP=0-9
1. Error occurs when 48 volt
distribution falls below 42
volts during powerup state
displayed. Powerup state
indicates which loads are
being turned on.
2. Excessive load on 48 volts due
to an inadequate number of
functioning 48 volt supplies
or overload condition on 48V
bus.
3. Possible node power supply
(NPS) lower right failure.
Call the Response Center.
LED Fault Symptoms Corrective action
- Operator’s Guide 1
- Revision History 2
- Contents 3
- Preface xiii 13
- Notational conventions 14
- Safety in material handling 16
- BCIQ (Taiwan) 17
- 3862H354 18
- Fuse cautions 19
- Associated documents 20
- Technical assistance 21
- Reader feedback 22
- 1Overview 23
- V-Class System Components 24
- The Service Support Processor 25
- (diagnostic LAN) 27
- Term. Server 27
- (console) 27
- SSP Workstation 27
- V-Class Server Architecture 28
- Chapter 1 7 29
- Overview 29
- HyperPlane Crossbar 29
- Core Utilities Board 31
- Processors 31
- Memory Interleaving 33
- CTI Cache Memory 33
- Input/Output 34
- 32103210 210210 35
- 0123 0123 35
- Chapter 1 19 41
- 20 Chapter 1 42
- 2 Indicators, switches, and 43
- DVD-ROM drive 44
- Key switch panel 44
- LCD display 44
- Optional DAT drive 44
- Headphone jack 46
- Volume control 46
- Busy indicator 46
- Disk loading slot 46
- Eject button 46
- Attention light bar 49
- MIII IIII IIII IIII 50
- IIII IIII IIII IIII 50
- Message display line 52
- Environmental errors 54
- 34 Chapter 2 56
- System Displays 56
- 3 SSP operation 57
- SSP and the V-Class system 58
- SSP log-on 59
- 38 Chapter 3 60
- SSP operation 60
- Chapter 3 39 61
- Message window 62
- Console bar 62
- Environment) Workspace menu 63
- 42 Chapter 3 64
- Using the console 67
- Console commands 71
- Watching the console 72
- CTRL-Ec 73
- CTRL-Ecf 73
- CTRL-Ecs 73
- Accessing system logs 74
- The set_complex command 74
- Targeting commands to nodes 75
- SSP file system 76
- /spp/bin 77
- /spp/scripts 77
- /spp/data/complex_name 77
- /spp/firmware 78
- /spp/est 78
- /spp/man 78
- Device files 79
- System log pathnames 80
- 4 Firmware (OBP and PDC) 81
- Boot sequence 82
- Boot process output 84
- Chapter 4 63 85
- Firmware (OBP and PDC) 85
- HP mode boot menu 86
- Enabling Autoboot 89
- Examples 90
- 70 Chapter 4 92
- HElp command 92
- 5 Configuration utilities 93
- Starting ts_config 94
- Configuration procedures 97
- Configure a Node 99
- Configure the scub_ip address 103
- Reset the Node 104
- Deconfigure a Node 106
- Remove terminal mux 107
- Console sessions 107
- 86 Chapter 5 108
- Configuration utilities 108
- /spp/scripts/inst/ts.install 118
- LAN communications 120
- Serial communications 121
- Chapter 5 103 125
- Menu bar 127
- Node configuration map 128
- Node control panel 129
- 114 Chapter 5 136
- 6 HP-UX Operating System 139
- HP-UX on the V2500/V2600 140
- HP-UX parameter sets 142
- HP-UX 11.10 SCA Enhancements 144
- HP-UX SCA Features 145
- Starting HP-UX 147
- Power-On Sequence 148
- Boot variables 149
- in a mode that 151
- command does 151
- command manually. If fsck 151
- 3. Other errors detected 151
- Stopping HP-UX 152
- Chapter 6 131 153
- HP-UX Operating System 153
- Rebooting the system 154
- Shutting down the system 155
- 136 Chapter 6 158
- 7 Recovering from failures 159
- Collecting information 160
- Performance problems 161
- System hangs 162
- System panics 163
- Peripheral problem 164
- File system problem 166
- LAN communication problem 166
- Abnormal system shutdowns 169
- Configuration criteria 172
- System recovery time 172
- Crash information integrity 174
- Disk space needs 176
- Defining dump devices 177
- The /etc/fstab file 181
- The crashconf command 181
- /sbin/crashconf -a 181
- /sbin/crashconf -ar 181
- Dump order 182
- Operator override options 183
- The dump 183
- The reboot 184
- Crash dump format conversion 185
- Analyzing crash dumps 186
- ALED codes 187
- Power on detected errors 188
- CUB detected processor error 194
- CUB detected I/O error 195
- CUB detected fan error 196
- CUB detected hard error 198
- CUB detected dc error 200
- Index 179 201
- 180 Index 202
- Index 181 203
- 182 Index 204
- Index 183 205
- 184 Index 206
Verwandte Produkte und Handbücher für Computers Hp 9000 V2600 SCA
Computers Hp RX8620-32 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Computers Hp 500B Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Computers Hp Media Center PC Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Computers Hp SA3150 Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Computers Hp AMS DL320 Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Computers Hp XW4300 Bedienungsanleitung
(90 Seiten)
(90 Seiten)
Computers Hp dc5700 Bedienungsanleitung
(216 Seiten)
(216 Seiten)
Computers Hp D2842W Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Computers Hp j6700 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Computers Hp ML100 Bedienungsanleitung
(111 Seiten)
(111 Seiten)
Computers Hp Compaq Bedienungsanleitung
(22 Seiten)
(22 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern