HP 9030 CE Wartungshandbuch

HP 9000 Series 500 Computers Models 530/540 HP 9030/9040 CE Handbook Part No. 09040-90035 E0385 Requires Binder No. 9282-0683 r/i~ HEWLETT ~e.. PACKAR

2-2 9030/40 Environmental/Installation/PM Installation Procedure 1. Unpack the computer. 2. Position the computer. Leave about 6 inches of space at e

9030/40 EnvironmentalllnstallationlPM 2-3 7. Install and connect the peripheral devices. 8. Connect the HP 97098A 110 Expander(s) I/O EXPANDER 1 8 _

2-4 903040 Environmental;Installation PM Preventive Maintenance There are no scheduled preventive maintenance procedures.

9020/9030/9040 Environmental/Installation/PM 2-5 Finstrate Installation Instructions for HP -Qualified Personnel: Start on page 2-6 (RAM/CPU), or 2-7

2-6 9020/9030/9040 Environmental/Installation/PM RAM/CPU Finstrate Installation 1. (ALL) TURN THE POWER OFF AND DISCONNECT THE POWER CORD. 2. (520)

9020/9030/9040 Environmental/Installation/PM 2-7 1. (ALL) lOP Finstrate Installation WARNING OBSERVE ALL WARNINGS AND SAFETY PROCEDURES IN THE COMPUT

2-8 902019030/9040 EnvironmentaLinstallation/ PM 4. (520 ONLY) Remove the flat metal plate covering the appropriate 1,0 EXPANDER connector slot by r

9020/9030/9040 Environmental/Installation/PM 2-9 CAUTION DO NOT TOUCH EDGE CONNECTOR OR FINSTRA TE PLANE. HOLD FINSTRA TE BY EJECTORS OR SIDE EDGES

2-10 9020/9030/9040 Environmenta[ilnstallation·PM 10. (520) Place lOP cable door connector over studs on ends of appropriate 110 EXPANDER con

9020/9030/9040 Environmental/Installation/PM 2-11 14. (ALL) Close processor stack door. Tighten thumbscrews to prevent Radio Frequency Interfer

9030/9040 CE Handbook © Copyright 1985, Hewlett-Packard Company. This document contains proprietary information which is protected by copyright All

2-12 902090309040 Environmental Installation PM Figure 6. Plastic lOP Connector Cover. 16. (530/540 ONLY) Route cable between terminal block and bas

9020/9030/9040 Environmental/Installation/PM 2-13 512K RAM Board Installation Information Instructions For HP-Qualified Personnel: Follow the instruc

2-14 9020/9030/9040 Environmentalilnstallation/PM 512K Byte RAM Board Installation 1. (ALL) TURN THE POWER OFF AND DISCONNECT THE POWER CORD. 2. (520

9020/9030/9040 Environmental/Installation/PM 2-15 1 Megabyte RAM Board Installation Instructions Read the following information then follow the ins

2-16 9020/9030/9040 Environmental/Installation/PM Part Numbers 1 Megabyte RAM Board (exchange) (new) Boot Loader ROM * Load Board 97046-69704 5061-770

9020/9030/9040 Environmental/Installation/PM 2-17 8. (520) Close the left side door. (530/540) Replace the RFI shield. 9. (520) Remove right side doo

2-18 9020/9030/9040 Environmental/Installation/PM 15. (520 With Bootstrap Loader Card) Remove Bootstrap Loader card and replace the Bootstrap Loader

9020/9030/9040 Environmental/Installation/PM 2-19 16. (520) Reinstall mass storage cover and right side door. (530/540) Reinstall I/O lid and connec

2-20 9020/9030/9040 Environmental/Installation/PM

9030/9040 Standard Features • Diagnostic Display Panel • Power Supply • 7 I/O Slots • Single CPU • Single I/O Processor • 512K Byte RAM • Rea

Chapter 1 9030/40 Product Information Chapter 2 9030 40 Environmental Installation PM Chapter 3 9030 40 Configuration Chapter 4 903040 Trouhleshooting

9030/9040 Standard Features Plus • Diagnostic Display Panel • Power Supply • 7 I/O Slots • Single CPU • Single I/O Processor • 512K Byte RAM •

System Console Messages Loade r Rel)-( ([0 of OS) Loader Re I) )-( ([0 of OS) Load done. Loader Rev){ ([0 of OS) Load done. (Copyright info) Loade r

4-2 9030140 Troubleshooting Indication S~ IQg~1 o POWER ON D o RUN DBD Note: No LEOs on. PROCESSOR Note: D D Note: Anyone of the 12 PROCESSOR LEOs m

Indication 45 15 I/O LEOS (l=on; O=off) Error No. 6 5 4 3 2 1 0 0 o 0 0 0 000 1 o 0 0 0 0 0 1 2 0000010 3 o 000 0 1 1 4 o 0 001 0 0

4-4 9030'40 Troubleshooting Indication Procedure [g IgQQI [g Igggi TEST DUMP TEST DUMP .POWeRON .POWERON o ORUN o ORUN Darn 1""---&ap

5-1 Chapter 5 9030/40 Diagnostics System Loader Messages Trailer NNNNN indicates Rev. A loader select codes. Example: Where: NNNNN is 21 2~ Remainde

5-2 9030/40 Diagnostics Error Code #6 Error Code #9 Error Code #11 BAD CARD DR DEVICE: NNNNN BAD CARD DR DEVICE: SELECT CODE NN - Informational messag

Error Code #20 Error Code #21 Error Code #22 Error Code #23 9030/40 Diagnostics 5-3 BAD RTC: NNNNN BAD RTC: SELECT CODE NN - Indicates that the built

5-4 9030/40 Diagnostics Self test error 4: Memory reduced to: NNNNNNNN Bytes. MCs:(list) Where: NNNNNNNN = number of bytes (in decimal) that are ava

9030/40 Diagnostics 5-5 Service Panel Switches Switch Function SELF TEST Pressing this latching switch initiates a continuous system self-tes

ii Printing History New editions of this manual will incorporate all material updated since the previous edition. Update packages may be issued betwee

5-6 9030140 Diagnostics Power Supply LEDs LED Indication When lit Cure DOORS OPEN Interface card cage door or processor Close door(sl, tighten thumbs

903040 Diagnostics 5-7 Service Processor Code Flowchart

5-8 9030/40 Diagnostics r--------., I Service Processor I -"1 Can Now Display I I Stack Fault Info I L ________ ...J is;nd AnyE;;o-;-Msg -, I

r---------, I Send Four 16~81t I I Patterns To From ~_ I A Keyboard Or SCM I I Register I L _________ .J r--------., ! Either No Card I I ~--

5-10 903040 Diagnostics

The 9030/40 has no adjustments. 6-1 Chapter 6 9030/40 Adjustments

6-2 9030;40 Adjustments

7-1 Chapter 7 9030/40 Peripherals Select Codes Select Code Usage 0 I/O Slot 0 1 1/0 Slot 1 2 110 510t 2 3 1/0510t3 4 LO 510t 4 5 1/0 510t 5 6 );0 5

7-2 903040 Peripherals 27110A HP-IBlnt_ 01' 1n .. ,...,1 HP-IB S7: -UP FOR NORMAL SPEED -DOWN FOR HIGH SPEED HP 27110A HP-IB Interface Card

9030/40 Peripherals 7-3 Available HP-IB Cables Product Length Number (in meters) 92220R 0.3 10833D 0.5 45529A 1.0 45529B 2.0 45529C 4.0 5060-9459

r 1-1 Chapter 1 9030/40 Product Information Features • 32-bit CPU and full 32-bit internal and external data paths. • Add-on performance with multi

7-4 9030/40 Peripherals SW2 S1: Bidirectional Bus Enable; E15 E16 W3 W2 Up - Disabled. Down - Enabled. S2: Internal Handshake Enable; Up - Disable

9030/40 Peripherals 7-5 To configure the GPIO card: 1. Install jumpers in WI, W2, and W3, according to whether 5-volt or 12-volt logic levels are to

7 -6 9030 40 Peripherals HP 27122A Remote Job Entry (RJE) Features • 1,200 to 19,200 baud rates. • Compatible with EIA RS-232C and CCITT V.24 specif

9030/40 Peripherals 7-7 HP 27128A Asynchronous Serial Interface (ASI) Features • Switch selectable and software programmable baud rate; up to 19,200

7 -8 9030AO Peripherals HP 27128A Asynchronous Serial Interface (ASI) Card

Std. Cable. 5m (27128-63002 or 8120-4309) Option 001 Cable. 5m (27122-63001 or 8120-4311i . I Cabling Termma f these ... Anyo I I \ ASI Interface C

7-10 9030/40 Peripherals HP 27130A/B Asynchronous 8-Channel Multiplex Features • CCITT V.28 and EIA RS-232C compatible. • Supports simplex, echople

9030/40 Peripherals 7-11 HP 97062A Color Video Features • Medium-resolution interface to 19-inch color monitor. • Produces RS-343-compatible signa

7-12 903040 Peripherals Set the bus address of the LAN unit to 0 by setting the switches on the back of the unit to these positions: I 27110A I HP-I

8-1 Chapter 8 9030/40 Replaceable Parts Exchange Parts New Rebuilt Part Number Part Number Description 09855-67980 09855-69980 Power Supply Assembly

1-2 9030/40 Product Information Memory • 256K byte RAM boards. • 512K byte RAM boards. • 1M byte RAM boards-2M byte increments. • RAM expandable to

8-2 903040 Replaceable Parts Replaceable Parts, Exploded View # 1 Index Total Number Part Number Item Description Qty 1 Front Panel, HP 9040 1 1600-

in parentheses ( ) identify NOTE: Small n~7:.:e;:rts. quantity of attac Exploded View # 1 8-3 9030/40 Replaceable Parts 'Xi, I 7 Y

8-4 9030 40 Replaceable Parts Replaceable Parts, Exploded View #2 Index Total Number Part Number Item Description Qty 1 Front Panel, HP 9030 1 1600-

9030/40 Replaceable Parts 8-5 Replaceable Parts, Exploded View #2, Continued Index Total Number Part Number Item Description Qty 26 Power Cord 1 0985

8-6 9030/40 Replaceable Parts

9030/40 R eplaceable Parts 8-7 21 33 26 3 I lew #2 Exploded V·

I I I PROCESSOR STACK MOTHERBOARD HAM I lOP I lOP sus cpu I I '-----r--t SERVICE PANEL SYSTEM CONTROL MODULE 9-1 Chapter 9 9030/40 Diagrams POWE

PRIMARY BOARD RECTIFIER AND CAPACITORS ~~-------------<'--7 ,19VUNREG 1--.i--;-+-o--9-j-l>--jr----::J[:--'II>-----,---r=-----=-t FU

SYSTEM CLOCK NOTES 1 MEMORY PROCESSOR BUS INCLUDES: ADDRESS, DATA, BUS CONTROL, POWER AND GROUND, SELF-TEST MISCELLANEOUS CONTROL 2 MEMORY CONTROLLER

9-4 9030,40 Diagrams CHIP SELECTS TO I.lPB 32 I.lEMORY CONTROLLER 256K RAM Finstrate Block Diagram

9030/40 Product Information 1-3 HP-UX System Software HP Product No. Single-user Multi-user Software 97079B 97089B(16) HP-UX Operating System 97088B(

t.tAPPER CAM REGISTER ADDRESS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 CS SELECTED RCNI 3 3 o 9030/40 Dia

9-6 9030140 Diagrams o 2 I ... ~-----LOGICAL MEMORY ADDRESS-----... -11 (27 BITS) 29 30 12 BITS 4 8 ~ CHIP ROW SELECT Y ADDRESS X ADDRESS P

HEALER CAM (ADDRESS) 0 31 I 10 11 • • • I~ I I I 0 I 9030/40 Diagrams 9-7 HEALER RAM (DATA) 31 32 39 DATA I CHECK 10 BITS 11 • • • 131 ~ 1=HEALED L

TO "P8 t.4EMQRY EVEN CHIP SELECTS

IMPPER CAM REGISTER ADDRESS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 CS SELECTED ROW o Y ADDRESS SELECTED

9-10 9030/40 Diagrams LOGICAL MEMORY ADDRESS ------I~__tl (27 BITS) 12 BITS 4 8 1 1 EVEN CS ROWS ODD CS ROWS Y ADDRESS X ADDRESS , I ~~~I X xl { 0 1

HEALER CAM (ADDRESS) 0 31 I ,0 11 • • • I~ / / / 0 I 9030/40 Diagrams 9-11 HEALER RAM (DATA) 31 32 39 DATA I CHECK ,0 BITS 11 • • • ,31 1=HEALED LOCA

9-12 9030/40 Diagrams MEMORY ADDRESS BUS AND CONTROL (9 ADDRESS AND 3 CONTROL-NRAS.NCAS.NWR) 12 MPB 32 MC MEMORY DATA BUS RAM CHIPS ARE 256K X 1 BI

9030/40 Diagrams 9-13 HEALER CAM HEALER RAM (ADDRESS) (DATA) 0 31 0 31 32 39 / / / [ • • • ,0 11 I~ I DATA I • • • ( 0 1 10 11 X AND Y ADDRESS ~ 1-H

9·14 9030/40 Diagrams System Control Module Block Diagram

1-4 9030/40 Product Information HP Part No. 09040-80030 09040-90011 09040-90038 09040-90035 09000-90040 97060-90030 97062-90020 97098-90020 27132-910

P1 1 '" .;4.. 1~14 B12 "'li A12 .,Ii A1 ..,. B1A A1 P3 A6 B 1:;J: ;c,. B6 P5 ~ B1 !k.A1 A1 "'Ii B1A P7 P9 i!* A18 !!...

9-16 9030/40 Diagrams Pl +3.85 25 + 3.85 24 +5 23 +5 22 +5 21 -2 20 GND 19 GND 18 GND 17 GND 16 GND 15 GND 14 GND 12 AC-11 AC+ 10 +5 9 + 19 +19 FAN

GNO U54 NMIO GNO ST8 ST6 STl ST3 STll ST10 10 GNO 11 NOO 12 NSTLEO 13 NPOOP 14 GND 15 -19 16 +19 17 GNO 18 P13 P9 [}FANGNO 4 FANP 3 FANGNO 2 -KEY-1

9-18 9030/40 Diagrams Motherboard Signal Definitions Signal Definition -KEY-Keyed hole in connector. -12 - 12 volt supply. -19 -19 volt supply. -2 - 2

Signal NIDO NIDOO NIDOI NID02 NID03 NID04 NID05 NID06 NID07 NID08 NID09 NIDOlO NIDOll NID012 NID013 NID014 NID015 NIDOP NIFC NIOSS NMI NMID NMYPA NPAO

9-20 9030/40 Diagrams Motherboard Signal Definitions (Continued) Signal Description STl Stack self-test from slot I. ST2 Stack self-test from slot 2

9030/40 Diagrams 9-21 110 Backplane 840_"'5 PO e!'"_81 A40---!!.-A1 P8 R 840_"!i P1 i!""_81 A40--!! il..-A1 2 1 840

9-22 9030/40 Diagrams 1/0 Backplane Signal Definitions Signal Definition -12 -12 volt supply. 12 12 volt supply. 5 5 volt supply. 5BB 5 volt supply, b

9030/40 Diagrams 9-23 I/O Backplane Signal Definitions (Continued) Signal Definition NSTS 110 bus status (negative true). NSWO Select code switch 0

9-24 9030/40 Diagrams SCM Connectors Designator Connecting Assembly L Motherboard (Connector PIO) S Motherboard (Connector P9) Service Panel Conn.

2-1 Chapter 2 9030/40 Environmental/InstallationlPM Physical and Environmental Specifications I System II Enclosure' I Stand-alone Mini-cabin

9030/40 Diagrams 9-25 SCM Signal Definitions Signal Definition -12 - 12 volt supply. -19 - 19 volt supply. 5 5 volt supply 5F 5 volt fused supply.

9-26 9030/40 Diagrams SCM Signal Definitions (Continued) Signal Definition NPFW Power fail warning (negative true). NPOLL 110 bus interface poll (n

10-1 Chapter 10 9030/40 Reference Real-Time ClockINon-Volatile Memory Contents Byte 0 -Byte 1 -Byte 2 -Byte 3 -Byte 4 -Byte 5 -Byte 6 -Byte 7

10-2 9030;40 References

11-1 Chapter 11 9030/40 Service Notes

11-2 9030/40 Service Notes