HP t5530 Bedienungsanleitung

Hardware Reference GuideHP Compaq t5135/t5530 Thin Clients

2. Press the tab (1), and then slide the stand about 1/2–inch toward the front of the unit and lift thestand off the unit (2).Figure 1-5 Removing the

(7)Application key1Similar to the right mouse button, opens pop-up menus in a MicrosoftOffice application. May perform other functions in other softwa

Serial number locationEvery thin client includes a unique serial number located as shown in the following illustration. Have thisnumber available when

2 Hardware changesGeneral hardware installation sequenceTo ensure the proper installation thin client hardware components:1. Back up any data, if nece

CAUTION: The ambient temperature inside of the secure USB compartment can reach up to 55°C inworst case conditions. Make sure the specifications for a

Installing the USB device▲Insert the USB device into the USB port in the secure USB compartment. See the followingillustration for the location of the

Replacing the batteryBefore beginning the replacement process, review General hardware installation sequence on page 7for procedures you should follow

2. Lift the metal side cover up and off the unit (2).Figure 2-5 Removing the metal side coverRemoving and replacing the batteryTo remove and replace

2. Insert and tighten the three screws.Figure 2-7 Replacing the metal side coverTo replace the access panel:1. Place the access panel on the side of

3 SpecificationsTable 3-1 HP Compaq t5135/t5530 Thin ClientDimensionsWidth (front to back)Height (top to bottom)Depth7.31 in.7.31 in2.06 in.18.57 cm1

© Copyright 2006, 2007 Hewlett-PackardDevelopment Company, L.P. Theinformation contained herein is subject tochange without notice.Microsoft and Windo

4 Security provisionsSecuring the thin clientThe HP Compaq t5135/t5530 thin client is designed to accept a security cable lock. This cable lockprevent

5 Mounting the thin clientHP Quick ReleaseThe HP Compaq t5135/t5530 thin client incorporates four mounting points on each side of the unit.These mount

To use the HP Quick Release with a VESA-configured thin client:1. Using four 10 mm screws included in the mounting device kit, attach one side of the

3. Slide the side of the mounting device attached to the thin client (1) over the other side of themounting device (2) on the device on which you want

Figure 5-6 Thin client mounted on back of monitor stand●You can mount the thin client on a wall.Figure 5-7 Thin client mounted on wall●You can mount

Figure 5-8 Thin client mounted under deskNon-supported mounting optionCAUTION: Mounting a thin client in an non-supported manner could result in fail

6 Thin client operationRoutine thin client careUse the following information to properly care for your thin client:●Never operate the thin client with

Figure 6-2 Horizontal orientation●You can lay the thin client under a monitor stand with at least one inch of clearance.Figure 6-3 Under monitor sta

Do not put thin clients in drawers or other sealed enclosures. Thin clients require proper ventilation tomaintain operating temperatures.Figure 6-4 D

7 Electrostatic dischargeA discharge of static electricity from a finger or other conductor may damage system boards or otherstatic-sensitive devices.

About This BookWARNING! Text set off in this manner indicates that failure to follow directions could result in bodilyharm or loss of life.CAUTION: Te

8 Shipping informationShipping preparationFollow these suggestions when preparing to ship the thin client:1. Turn off the thin client and external dev

iv About This Book ENWW

Table of contents1 Product featuresStandard features ...

Grounding methods ... 238 Sh

1 Product featuresStandard featuresThank you for purchasing an HP Compaq thin client. We hope you have years of use from our t5135 ort5530 thin client

(1) Secure USB compartment (5) Line-out (headphone) audio connector(2) Power button (6) Line-in (microphone) connector(3) Flash activity LED (7) Unive

(2) Ethernet RJ-45 connector (6) Monitor connector(3) Parallel connector (7) Serial connector(4) Universal serial bus (USB) connectors (4) (8) Power c