HP 5300 Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach PC / Workstation Barebones HP 5300 herunter. HP 5300 Installation guide Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 1

hp procurve switchxl modulesinstallation guidewww.hp.com/go/hpprocurve

Seite 2

4HP ProCurve Switch xl ModulesFeaturesFeatures and functionality of the ProCurve Switch Access Controller xl Module (J8162A). Shutdown Module—This is

Seite 3

5HP ProCurve Switch xl ModulesFeatures Module Ready LED—This LED comes on after the module completes the boot up and self test processes and indicate

Seite 4

6HP ProCurve Switch xl ModulesFeaturesThe ProCurve Switch xl Modules have the following features: auto-enabled ports—the ports are all configured to

Seite 5 - Contents

7HP ProCurve Switch xl ModulesInstalling the ModulesInstalling the ModulesOverviewBefore installing any module, ensure you have loaded the most curren

Seite 6

8HP ProCurve Switch xl ModulesInstalling the ModulesInstalling the Module in an Unused SlotInstallation Procedures:1. Use a Torx T-10 or flat-bladed s

Seite 7

9HP ProCurve Switch xl ModulesInstalling the Modules1. Insert module into the guides and slide it in until it is fully inserted.“Low-force” connector

Seite 8

10HP ProCurve Switch xl ModulesInstalling the ModulesInstalling or Removing the mini-GBICsYou can install or remove a mini-GBIC from the mini-GBIC xl

Seite 9

11HP ProCurve Switch xl ModulesInstalling the ModulesConnecting an HP ProCurve External Power Supply Power over Ethernet technology allows IP telephon

Seite 10 - Features

12HP ProCurve Switch xl ModulesInstalling the Modules5. Install (or re-install) the RJ45 connectors in ports 6 and 13.The opposite procedure is used w

Seite 11 - Battery Installation Required

13HP ProCurve Switch xl ModulesInstalling the ModulesHP ProCurve Switch PoE xl Module ConfigurationsFor the HP ProCurve Switch PoE xl Module to functi

Seite 13 - “Hot Swap”

14HP ProCurve Switch xl ModulesInstalling the ModulesPoE Power RequirementsWhen a powered device (PD) is initially connected to a PoE port, a minimum

Seite 14 - Installation Precautions:

15HP ProCurve Switch xl ModulesInstalling the ModulesPoE Module LEDsPort LEDsThere are two LEDs for each port: The Link LED lights with a valid 10bas

Seite 15 - 1. Insert module into the

16HP ProCurve Switch xl ModulesInstalling the ModulesLED Mode LEDsThe Std or PoE LED lights depending on which mode has been selected by pressing the

Seite 16 - Installing the Modules

17HP ProCurve Switch xl ModulesInstalling the ModulesVerifying the Module is Installed CorrectlyObserve the Module Status LED for the slot in which th

Seite 17 - Connecting the EPS connector

18HP ProCurve Switch xl ModulesInstalling the ModulesConnecting the Network CablesConnect the appropriate network cables to the module's ports as

Seite 18

19HP ProCurve Switch xl ModulesInstalling the ModulesModule Cable Type Maximum Lengthmini-GBIC and the 10/100/1000-T xl ModulesGigabit-SX operation:mu

Seite 19

20HP ProCurve Switch xl ModulesInstalling the ModulesNote Automatic Cable Sensing on Twisted-Pair Ports:When the ports for the 10/100-TX, 100/1000-T,

Seite 20 - PoE Power Requirements

21HP ProCurve Switch xl ModulesInstalling the ModulesVerifying the Network Connections Are WorkingCheck the port LEDs for the newly-installed module t

Seite 21 - PoE Module LEDs

22HP ProCurve Switch xl ModulesInstalling the ModulesCustomizing the Port ConfigurationIf the slot in which you installed the module was empty the las

Seite 22 - LED Mode LEDs

23HP ProCurve Switch xl ModulesInstalling the ModulesIf necessary, configure the port(s) in the module by using the switch console or the web browser

Seite 23 - Module Link and Mode

HP ProCurve Switch xl ModulesInstallation Guide

Seite 24 - Connecting the Network Cables

24HP ProCurve Switch xl ModulesReplacing or Removing a ModuleReplacing or Removing a ModuleFollow these procedures to replace one module with another,

Seite 25 - 123456789101112

25HP ProCurve Switch xl ModulesResetting the SwitchResetting the SwitchReasons for Resetting the SwitchGenerally, you only need to reset the switch wh

Seite 26

26HP ProCurve Switch xl ModulesTroubleshootingTroubleshootingOne of the primary tools for troubleshooting the switch modules are the LEDs on the front

Seite 27

27HP ProCurve Switch xl ModulesTroubleshooting On - When power is being supplied to the ports Off - When power is not requested Slow Blink - Wh

Seite 28 - ■ Flow Control: Disabled

28HP ProCurve Switch xl ModulesTroubleshootingTip NumberProblem Solution➊The module installed in the slot that corresponds to the letter that is blink

Seite 29

29HP ProCurve Switch xl ModulesTroubleshooting➌A module was installed in the slot that is a different type than the previously installed module, and t

Seite 30

30HP ProCurve Switch xl ModulesTroubleshooting➏The network connection is not working properly.Try the following procedures:• For the indicated port, v

Seite 31 - Resetting the Switch

31HP ProCurve Switch xl ModulesCustomer Support ServicesCustomer Support ServicesIf you are having any trouble with your module or switch, Hewlett-Pac

Seite 32 - PoE LED Behavior

32HP ProCurve Switch xl ModulesSpecificationsConnectorsTwisted-Pair 10/100Base-TX RJ-45 – On the 10/100-TX xl Module.They are compatible with the IEE

Seite 33 - Diagnostic Tips:

33HP ProCurve Switch xl ModulesSpecificationsCablesTwisted-Pair CablesNote on 1000Base-T Cable Requirements. The Category 5 networking cables that wo

Seite 34

Hewlett-Packard Company8000 Foothills Boulevard, m/s 5552Roseville, California 95747-5552http://www.hp.com/go/procurve© Copyright 2001, 2005 Hewlett-

Seite 35

34HP ProCurve Switch xl ModulesSpecificationsFiber-Optic CablesPort Type Cable Specifications Connector TypeMaximum Length100Base-FX 62.5/125 µm or 50

Seite 36

35HP ProCurve Switch xl ModulesMode Conditioning Patch Cord for Gigabit-LXMode Conditioning Patch Cord for Gigabit-LXThe following information applies

Seite 37 - Environmental

36HP ProCurve Switch xl ModulesMode Conditioning Patch Cord for Gigabit-LXInstalling the Patch CordAs shown in the illustration below, connect the pat

Seite 38 - Connectors

37HP ProCurve Switch xl ModulesEMC Regulatory StatementsEMC Regulatory StatementsU.S.A.FCC Class AThis equipment has been tested and found to comply w

Seite 39 - Twisted-Pair Cables

38HP ProCurve Switch xl ModulesEMC Regulatory StatementsKoreaTaiwanEuropean Community Declaration of ConformityThese products are designed for operati

Seite 40 - Fiber-Optic Cables

— This page is intentionally unused. —

Seite 41 - Gigabit-LX

— This page is intentionally unused. —

Seite 42 - Recommended Patch Cords

— This page is intentionally unused. —

Seite 43 - Australia/New Zealand

Technical information in this document is subject to change without notice.Copyright Hewlett-Packard Company, 2001, 2005. All rights reserved. Reprod

Seite 44 - EMC Regulatory Statements

iiiContentsDescriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Features . . . .

Seite 45

ivCustomer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Specifications . . . . . . . . . . . .

Seite 46

1HP ProCurve Switch xl ModulesDescriptionsHP ProCurve Switch xl ModulesFor the HP ProCurve Series 5300xl SwitchesDescriptions. The HP ProCurve Switch

Seite 47

2HP ProCurve Switch xl ModulesDescriptionsHP ProCurve SwitchPoE xl Module (J8161A) 2 24 10/100-TX ports and when connected to an HP ProCurve 600 Redu

Seite 48 - *5991-2130*

3HP ProCurve Switch xl ModulesFeaturesFeatureshp procurve10/100 -TXxl moduleJ4820Axlmoduleretaining screwnetwork portsLink and Mode LEDs(one pair per

Kommentare zu diesen Handbüchern

Keine Kommentare